That will fail, and it already exports whole trees.
f6dd34ca81 made it sync content with
import remotes, and if an import remote is also an export remote, that
caused this new failure mode.
Sponsored-by: Brock Spratlen on Patreon
* config: Added the --show-origin and --for-file options.
* config: Support annex.numcopies and annex.mincopies.
There is a little bit of redundancy here with other code elsewhere that
combines the various configs and selects which to use. But really only
for the special case of annex.numcopies, which is a git config that does
not override the annex branch setting and for annex.mincopies, which does
not have a git config but does have gitattributes settings as well as the
annex branch setting.
That seems small enough, and unlikely enough to grow into a mess that it was
worth supporting annex.numcopies and annex.mincopies in git-annex config
--show-origin. Because these settings are a prime thing that someone might
get confused about and want to know where they were configured.
And, it followed that git-annex config might as well support those two
for --set and --get as well. While this is redundant with the speclialized
commands, it's only a little code and it makes it more consistent.
Note that --set does not have as nice output as numcopies/mincopies
commands in some special cases like setting to 0 or a negative number.
It does avoid setting to a bad value thanks to the smart
constructors (eg configuredNumCopies).
As for other git-annex branch configurations that are not set by git-annex
config, things like trust and wanted that are specific to a repository
don't map to a git config name, so don't really fit into git-annex config.
And they are only configured in the git-annex branch with no local override
(at least so far), so --show-origin would not be useful for them.
Sponsored-by: Dartmouth College's DANDI project
This didn't used to be needed because importKeys would import all
content and so doing another pass was redundant.
But since 40017089f2 it uses
importChanges, so only new files are imported. If a file that was
already imported before was dropped, that would prevent sync --content
from gettng its content again.
Sponsored-by: Jack Hill on Patreon
Large speed up to importing trees from special remotes that contain a lot
of files, by only processing changed files.
Benchmarks:
Importing from a special remote that has 10000 files, that have all been
imported before, and 1 new file sped up from 26.06 to 2.59 seconds.
An import with no change and 10000 unchanged files sped up from 24.3 to
1.99 seconds.
Going up to 20000 files, an import with no changes sped up from
125.95 to 3.84 seconds.
Sponsored-by: k0ld on Patreon
For simplicity, I've not tried to make it handle History yet, so when
there is a history, a full import will still be done. Probably the right
way to handle history is to first diff from the current tree to the last
imported tree. Then, diff from the current tree to each of the
historical trees, and recurse through the history diffing from child tree
to parent tree.
I don't think that will need a record of the previously imported
historical trees, and so Logs.Import doesn't store them. Although I did
leave room for future expansion in that log just in case.
Next step will be to change importTree to importChanges and modify
recordImportTree et all to handle it, by using adjustTree.
Sponsored-by: Brett Eisenberg on Patreon
Consistency with sync and internal consistency is more important than
consistency with the assistant, which is not itself consistent about
what it does when run in a subdirectory.
Note that with -C, it will still commit staged changes to files outside
the directory. Like sync does. Presumably if the user is manually
staging things, then running this command, they intend to build up a
commit.
Sponsored-by: unqueued on Patreon
assist: New command, which is the same as git-annex sync but with
new files added and content transferred by default.
(Also this fixes another reversion in git-annex sync,
--commit --no-commit, and --message were not enabled, oops.)
See added comment for why git-annex assist does commit staged
changes elsewhere in the work tree, but only adds files under
the cwd.
Note that it does not support --no-commit, --no-push, --no-pull
like sync does. My thinking is, why should it? If you want that
level of control, use git commit, git annex push, git annex pull.
Sync only got those options because pull and push were not split
out.
Sponsored-by: k0ld on Patreon
When used without --content or --no-content, warn about the upcoming
transition, and suggest using one of the options, or setting
annex.synccontent.
Sponsored-by: Brett Eisenberg on Patreon
This option is not specific to sync, so it seemed it should be in either
pull or push as well as sync. Since it does modify the remote, it seems
better to have it in push; the modification of the local repo pulls in
the direction of pull, but not hard enough.
Maybe it would be better to have it in both?
Sponsored-by: Luke Shumaker on Patreon
I anticipate that if sync is transitioned to syncing content by default,
people will want a short option. And in repositories where
annex.synccontent = true, they already would. And pull and push sync
content by default, so a short option is useful with them too.
Mnemonic: -g makes only git data be synced
Also, -a makes only annex data be synced.
Would have preferred -c, which would complement -C, but it
was already taken to set git configs.
Sponsored-by: Noam Kremen on Patreon
Split out two new commands, git-annex pull and git-annex push. Those plus a
git commit are equivilant to git-annex sync.
In a sense, git-annex sync conflates 3 things, and it would have been
better to have push and pull from the beginning and not sync. Although
note that git-annex sync --content is faster than a pull followed by a
push, because it only has to walk the tree once, look at preferred
content once, etc. So there is some value in git-annex sync in speed, as
well as user convenience.
And it would be hard to split out pull and push from sync, as far as the
implementaton goes. The implementation inside sync was easy, just adjust
SyncOptions so it does the right thing.
Note that the new commands default to syncing content, unless
annex.synccontent is explicitly set to false. I'd like sync to also do
that, but that's a hard transition to make. As a start to that
transition, I added a note to git-annex-sync.mdwn that it may start to
do so in a future version of git-annex. But a real transition would
necessarily involve displaying warnings when sync is used without
--content, and time.
Sponsored-by: Kevin Mueller on Patreon
The man page is somewhat vague about this, but I do think it was a bug
that these options didn't alreay behave that way. The options are
documented to disable imports and exports, which is the same operations
just with a special remote that uses trees.
The real motivation for this is that I'm adding git-annex pull and
git-annex push, and I want these options to turn off the equivilant of
those commands. And git-annex pull will certianly download and push
upload.
Sponsored-by: Nicholas Golder-Manning on Patreon
That was added in 2011 to prevent writing to the git-annex branch on
shutdown. But, the use of saveState causes pending git-annex branch
writes to be completed before the branch is deleted. So, an unusual exit
is not needed.
Had to convert uninit to do everything that can error out inside a
CommandStart. This was harder than feels nice.
(Also, in passing, converted CommandCheck to use a data type, not a
weird number that it was not clear how it managed to be unique.)
Sponsored-By: the NIH-funded NICEMAN (ReproNim TR&D3) project
I think this was just copied from another command without paying
attention to what it did, because there does not seem to be any valid
reason to want to only unannex some files when running uninit.
Seems unlikely to be too useful, but who knows.
Moved the checkSafeConfig call to happen after an action is started, so
it will be captured by --json-error-messages
Sponsored-By: the NIH-funded NICEMAN (ReproNim TR&D3) project
Including special --whatelse handling.
Otherwise, it seems unlikely to be too useful, but who knows.
Refactored code to call starting before displaying error messages.
This makes the error messages be captured by --json-error-messages
Sponsored-By: the NIH-funded NICEMAN (ReproNim TR&D3) project
Seems unlikely to be very useful, but trivial.
And, this completes the story that git-annex sync does not need json,
since every sub-operation is available in a command that does support json.
(Well, except for committing, but that's not a git-annex command.)
Sponsored-By: the NIH-funded NICEMAN (ReproNim TR&D3) project
The input field is consistently the url of the feed, which makes sense
as that is the user input, but to differentiate multiple urls downloaded
from a feed when using --json-progress -J, need the url that is being
downloaded too.
Sponsored-By: the NIH-funded NICEMAN (ReproNim TR&D3) project
Both -J and --json needed importfeed to be refactored to use commandAction.
That was difficult, because of the interrelated nature of downloading feeds
and then downloading files from feeds, both of which needed to use
commandAction. And then checking for problems in feeds has to come after
these actions, which may be run as background jobs.
As for --json support, it's most of the way there, but still has some
warts, so I didn't enable jsonOptions yet. The warts include:
- An initial empty json record is displayed by getCache.
- Input is not populated, should be feed url
- feedProblem at end will not be captured by --json-error-messages
(see FIXME)
Sponsored-By: the NIH-funded NICEMAN (ReproNim TR&D3) project
Also fix support for operating on multiple pairs of files and keys.
Moved notAnnexed to inside starting, so error message will get into the json.
Cannot include the key in the starting as it's not known yet, so instead
add it to the json later.
Sponsored-By: the NIH-funded NICEMAN (ReproNim TR&D3) project
Dunno how useful this will be, since about all that's accessible from
the json is whether it succeeded or failed, and the error messages
which were already on stderr.
Note that, when autoenabling a special remote, it would be possible for
one to stop and prompt or output not using Messages and so not output as
part of the json. I don't think that happens, but I'm not 100% sure
something doesn't manage to break it. Of course, the same could be the
case for commands that transfer objects. Using Annex.Init.autoEnableSpecialRemotes
in --json mode would avoid the problem, but I've chosen to wait until I
know it's needed to use it.
Sponsored-By: the NIH-funded NICEMAN (ReproNim TR&D3) project
Generalized AddJSONActionItemField to allow it to add several fields. Not entirely
happy with that, since the names of the fields have to be carefully chosen to
not conflict with other json fields. And fields added that way can't be parsed
back in FromJSON, except for the "fields" field that is special cased for metadata.
Still, I couldn't see another way to do it.
Also, omit file:null from the json output. Which does affect other commands,
eg git-annex whereis --all --json. Hopefully that won't break something that expects
a null file. If it did, that could be reverted, but it would be ugly to have
file:null in the unused --json
Sponsored-By: the NIH-funded NICEMAN (ReproNim TR&D3) project
For expire, the normal output is unchanged, but the --json output includes the uuid
in machine parseable form. Which could be very useful for this somewhat obscure
command. That needed ActionItemUUID to be implemented, which seemed like a lot
of work, but then ---
I had been going to skip implementing them for trust, untrust, dead, semitrust,
and describe, but putting the uuid in the json is useful information, it tells
what uuid git-annex picked given the input. It was not hard to support
these once ActionItemUUID was implemented.
Sponsored-By: the NIH-funded NICEMAN (ReproNim TR&D3) project
This also changes addunused to display the names of the files that it adds.
That seems like a general usability improvement, and not displaying the input
number does not seem likely to be a problem to a user, since the filename
is based on the key. Displaying the filename was necessary to get it and the key
included in the json.
dropunused does not include the key in the json. It would be possible to
add, but would need more changes. And I doubt that dropunused --json
would be used in a situation where a program cared which keys were
dropped. Note that drop --unused does have the key in its json, so such
a program could just use it. Or could just dropkey --batch with the
specific keys it wants to drop if it cares about specific keys.
Sponsored-By: the NIH-funded NICEMAN (ReproNim TR&D3) project
Also in passing the --all display was fixed up to not quote keys like filenames.
Note that the check added to compareChanges was needed to avoid logging when
nothing changed.
Sponsored-By: the NIH-funded NICEMAN (ReproNim TR&D3) project
log: When --raw-date is used, display only seconds from the epoch, as
documented, omitting a trailing "s" that was included in the output
before.
Sponsored-By: the NIH-funded NICEMAN (ReproNim TR&D3) project
The json does not include an url field, but it does have an input field that is
"file url" when using --batch and ["file", "url"] when using the command line.
I chose not to change that because it would complicate batchInput.
An url field could be added if it turns out to be useful.
Sponsored-By: the NIH-funded NICEMAN (ReproNim TR&D3) project
That's too much quoting, the user expects the filename to be copy and
pasteable. It would be ok to slash-escape space ('\ ')
which is what gnu find does, but it doesn't seem necessary either.
${escaped_file} has always quoted spaces though, so keep on doing it
there.
Sponsored-by: Nicholas Golder-Manning on Patreon
When a nonexistant file is passed to a command and --json-error-messages
is enabled, output a JSON object indicating the problem.
(But git ls-files --error-unmatch still displays errors about such files in
some situations.)
I don't like the duplication of the name of the command introduced by this,
but I can't see a great way around it. One way would be to pass the Command
instead.
When json is not enabled, the stderr is unchanged. This is necessary
because some commands like find have custom output. So dislaying
"find foo not found" would be wrong. So had to complicate things with
toplevelFileProblem having different output with and without json.
When not using --json-error-messages but still using --json, it displays
the error to stderr, but does display a json object without the error. It
does have an errorid though. Unsure how useful that behavior is.
Sponsored-by: Dartmouth College's Datalad project
New command, currently limited to changing autoenable= setting of a special remote.
It will probably never be used for more than that given the limitations on
it.
Sponsored-by: Brock Spratlen on Patreon
enableremote: Support enableremote of a git remote (that was previously set
up with initremote) when additional parameters such as autoenable= are
passed.
The enableremote special case for regular git repos is intended to handle
ones that don't have a UUID probed, and the user wants git-annex to
re-probe. So, that special case is still needed. But, in that special
case, the user is not passing any extra parameters. So, when there are
parameters, instead run the special remote setup code. That requires there
to be a uuid known already, and it allows changing things like autoenable=
Remote.Git.enableRemote changed to be a no-op if a git remote with the name
already exists. Which it generally will in this case.
Sponsored-by: Jack Hill on Patreon
These are quite low-level, but still there is no point in displaying
escape sequences that have been embedded in a key to the terminal.
I think these are the only remaining commands that didn't use safe
output, except for cases where git-annex is speaking a protocol to
itself.
Sponsored-by: Kevin Mueller on Patreon
When displaying a ByteString like "💕", safeOutput operates on
individual bytes like "\240\159\146\149" and isControl '\146' = True,
so it got truncated to just "\240".
So, only treat the low control characters, and DEL, as control
characters.
Also split Utility.Terminal out of Utility.SafeOutput. The latter needs
win32, but Utility.SafeOutput is used by Control.Exception, which is
used by Setup.
Sponsored-by: Nicholas Golder-Manning on Patreon
Searched for uses of putStr and hPutStr and changed appropriate ones to filter
out control characters and quote filenames.
This notably does not make find and findkeys quote filenames in their default
output. Because they should only do that when stdout is non a pipe.
A few commands like calckey and lookupkey seem too low-level to make sense to filter
output, so skipped those.
Also when relaying output from other commands that is not progress output,
have git-annex filter out control characters.
Sponsored-by: k0ld on Patreon
This does, as a side effect, make long notes in json output not
be indented. The indentation is only needed to offset them
underneath the display of the file they apply to, so that's ok.
Sponsored-by: Brock Spratlen on Patreon
Converted warning and similar to use StringContainingQuotedPath. Most
warnings are static strings, some do refer to filepaths that need to be
quoted, and others don't need quoting.
Note that, since quote filters out control characters of even
UnquotedString, this makes all warnings safe, even when an attacker
sneaks in a control character in some other way.
When json is being output, no quoting is done, since json gets its own
quoting.
This does, as a side effect, make warning messages in json output not
be indented. The indentation is only needed to offset warning messages
underneath the display of the file they apply to, so that's ok.
Sponsored-by: Brett Eisenberg on Patreon
giveup changed to filter out control characters. (It is too low level to
make it use StringContainingQuotedPath.)
error still does not, but it should only be used for internal errors,
where the message is not attacker-controlled.
Changed a lot of existing error to giveup when it is not strictly an
internal error.
Of course, other exceptions can still be thrown, either by code in
git-annex, or a library, that include some attacker-controlled value.
This does not guard against those.
Sponsored-by: Noam Kremen on Patreon
When the filenames are part of the git repository or other files that
might have attacker-controlled names, quote them in error messages.
This is fairly complete, although I didn't do the one in
Utility.DirWatcher.INotify.hs because that doesn't have access to
Git.Filename or Annex.
But it's also quite possible I missed some. And also while scanning for
these, I found giveup used with other things that could be attacker
controlled to contain control characters (eg Keys). So, I'm thinking
it would also be good for giveup to just filter out control characters.
This commit is then not the only line of defence, but just good
formatting when git-annex displays a filename in an error message.
Sponsored-by: Kevin Mueller on Patreon
As well as escape sequences, control characters seem unlikely to be desired when
doing addurl, and likely to trip someone up. So disallow them as well.
I did consider going the other way and allowing filenames with control characters
and escape sequences, since git-annex is in the process of escaping display
of all filenames. Might still be a better idea?
Also display the illegal filename git quoted when it rejects it.
Sponsored-by: Nicholas Golder-Manning on Patreon
Added StringContainingQuotedPath, which is used for ActionItemOther.
In the process, checked every ActionItemOther for those containing
filenames, and made them use quoting.
Sponsored-by: Graham Spencer on Patreon
This is by no means complete, but escaping filenames in actionItemDesc does
cover most commands.
Note that for ActionItemBranchFilePath, the value is branch:file, and I
choose to only quote the file part (if necessary). I considered quoting the
whole thing. But, branch names cannot contain control characters, and while
they can contain unicode, git coes not quote unicode when displaying branch
names. So, it would be surprising for git-annex to quote unicode in a
branch name.
The find command is the most obvious command that still needs to be
dealt with. There are probably other places that filenames also get
displayed, eg embedded in error messages.
Some other commands use ActionItemOther with a filename, I think that
ActionItemOther should either be pre-sanitized, or should explicitly not
be used for filenames, so that needs more work.
When --json is used, unicode does not get escaped, but control
characters were already escaped in json.
(Key escaping may turn out to be needed, but I'm ignoring that for now.)
Sponsored-by: unqueued on Patreon
registerurl: When an url is claimed by a special remote other than the web,
update location tracking for that special remote.
registerurl's behavior was changed in commit
451171b7c1, apparently accidentially to not
update location tracking except for the web.
This makes registerurl followed by unregisterurl not be a no-op, when the
url happens to be claimed by a remote other than the web. It is a noop when
the url is unclaimed except by the web. I don't like the inconsistency,
and wish that registerurl and unregisterurl never updated location
tracking, which would be more in keeping with them being plumbing.
But there is the fact that it used to behave this way, and also it was
inconsistent that it updated location tracking for the web but not for
other remotes, unlike addurl. And there's an argument that the user might
not know what remote to expect to claim an url, so would be considerably in
the dark when using registerurl. (Although they have to know what content
gets downloaded, since they specify a key..)
Sponsored-By: the NIH-funded NICEMAN (ReproNim TR&D3) project
This serves two purposes. --remote=web bypasses other special remotes that
claim the url, same as addurl --raw. And, specifying some other remote
allows making sure that an url is claimed by the remote you expect,
which makes then using setpresentkey not be fragile.
Sponsored-By: the NIH-funded NICEMAN (ReproNim TR&D3) project
The temporary URL key used for the download, before the real key is
generated, was blocked by annex.securehashesonly.
Fixed by passing the Backend that will be used for the final key into
runTransfer. When a Backend is provided, have preCheckSecureHashes
check that, rather than the key being transferred.
Sponsored-by: unqueued on Patreon
That is a legal url, but parseUrl parses it to "/c:/path"
which is not a valid path on Windows. So as a workaround, use
parseURIPortable everywhere, which removes the leading slash when
run on windows.
Note that if an url is parsed like this and then serialized back
to a string, it will be different from the input. Which could
potentially be a problem, but is probably not in practice.
An alternative way to do it would be to have an uriPathPortable
that fixes up the path after parsing. But it would be harder to
make sure that is used everywhere, since uriPath is also used
when constructing an URI.
It's also worth noting that System.FilePath.normalize "/c:/path"
yields "c:/path". The reason I didn't use it is that it also
may change "/" to "\" in the path and I wanted to keep the url
changes minimal. Also noticed that convertToWindowsNativeNamespace
handles "/c:/path" the same as "c:/path".
Sponsored-By: the NIH-funded NICEMAN (ReproNim TR&D3) project
Such an url is not valid; parseURI will fail on it. But git-annex doesn't
actually need to parse the url, because all it needs to do to support
syncing with it is know that it's not a local path, and use git pull and
push.
(Note that there is no good reason for the user to use such an url. An
absolute url is valid and I patched git-remote-gcrypt to support them
years ago. Still, users gonna do anything that tools allow, and
git-remote-gcrypt still supports them.)
Sponsored-by: Jack Hill on Patreon
copy: When --from and --to are combined and the content is already present
on the destination remote, update location tracking as necessary.
Sponsored-by: Dartmouth College's DANDI project
When importing a bunch of feeds, this makes it more clear what it's working
on. Also, I sometimes want to delete a particular feed from a list of feeds
but don't know which url belongs to the feed, and this solves that.
Control characters are filtered out just to protect against some feed
putting escape character stuff in the feed, which could be a
security problem. (Control characters also get filtered out of
importfeed filenames.)
Sponsored-by: Luke Shumaker on Patreon
sync: Fix a reversion that prevented sending files to exporttree=yes
remotes when annex-tracking-branch was configured to branch:subdir
(Introduced in version 10.20230214)
Sponsored-by: Kevin Mueller on Patreon
Works around this bug in unix-compat:
https://github.com/jacobstanley/unix-compat/issues/56
getFileStatus and other FilePath using functions in unix-compat do not do
UNC conversion on Windows.
Made Utility.RawFilePath use convertToWindowsNativeNamespace to do the
necessary conversion on windows to support long filenames.
Audited all imports of System.PosixCompat.Files to make sure that no
functions that operate on FilePath were imported from it. Instead, use
the equvilants from Utility.RawFilePath. In particular the
re-export of that module in Common had to be removed, which led to lots
of other changes throughout the code.
The changes to Build.Configure, Build.DesktopFile, and Build.TestConfig
make Utility.Directory not be needed to build setup. And so let it use
Utility.RawFilePath, which depends on unix, which cannot be in
setup-depends.
Sponsored-by: Dartmouth College's Datalad project
As far as I can see, git-annex status was added to support direct mode, and
like other things added for that, it ought to be deprecated.
Behavior is similar to git status --short, though not identical in a few
cases eg renamed files.
I think datalad does not use this command, although it might have in the
past. Could not find any use of it in the current datalad code.
A deprecation warning at runtime would be the next step, probably will wait
and do that for all the deprecated commands together (except findref).
Rather than entering a view of the adjusted branch, enter an adjusted
view branch. This way, it's the same as first using git-amnnex view
followed by git-annex adjust, and everything already implemented to
support that works.
Sponsored-by: Nicholas Golder-Manning on Patreon
When generating the view, check if the key is present.
When syncing in a view branch with an adjustment, run adjustedBranchRefreshFull
the same as is done when syncing in other adjusted branches. This is
needed because the docs for git-annex adjust --unlock-present suggest
using git-annex sync to update the branch when annex.adjustedbranchrefresh
is not set.
Note that, with annex.adjustedbranchrefresh set, it just works! The
adjusted branch gets updated in the usual way and it doesn't matter that
there's a view branch underneath.
And of course, re-running git-annex adjut --unlock-present also works,
as suggested in the docs.
Sponsored-by: Erik Bjäreholt on Patreon
An adjusted view branch has a name like
"refs/heads/adjusted/views/master(author=_)(unlocked)", so it is a view
branch that has been converted to an adjusted branch.
Made Logs.View support such branch names. So now git-annex sync and
pre-commit handle updating metadata on commit in such a branch.
Much remains to be done to fully support adjusted view branches,
including actually applying the adjustment when updating the view branch.
Sponsored-by: Graham Spencer on Patreon
info: Fix reversion in last release involving handling of unsupported input
by continuing to handle any other inputs, before exiting nonzero at the
end.
Sponsored-by: Dartmouth College's Datalad project
Used to fail with a bad error message, indicating there was no
repository with the specified name, or something like that. Now, suggest
they use the uuid to disambiguate.
* info, enableremotemote, renameremote: Avoid a confusing message when more
than one repository matches the user provided name.
* info: Exit nonzero when the input is not supported.
Sponsored-by: Kevin Mueller on Patreon
sync: Fix a bug that caused files to be removed from an importtree=yes
exporttree=yes special remote when the remote's annex-tracking-branch was
not the currently checked out branch.
Sponsored-by: Max Thoursie on Patreon
* sync: When run in a view branch, refresh the view branch to reflect any
changes that have been made to the parent branch or metadata.
This is basically working, but probably needs some more work to deal with
all the edge cases of things sync does.
Sponsored-by: Lawrence Brogan on Patreon
* sync: Avoid pushing view branches to remotes.
* Changed the name of view branches to include the parent branch.
Existing view branches checked out using an old name will still work.
It does not seem useful for sync to push view branches around, because
the information in a view branch can entirely be derived from other
information in git. And sync doesn't push adjusted branches around either.
The better view branch names make it more in line with adjusted branch
names, but were also needed to make fromViewBranch be able to return the
original branch name.
Kept the old view branch names still working. But, when those branches
exist in a repo, sync will still try to push them as before. Avoiding
that would need more complicated and/or expensive changes to sync.
Sponsored-By: Boyd Stephen Smith Jr. on Patreon
And also to vadd usage.
Also added some other things to the usage that were omitted before to
save space.
Adding even FIELD?=GLOB made the git-annex --help list of commands grow
too wide for an 80 column display. So, removed the description of
parameters from that list of commands.
Sponsored-By: Brock Spratlen on Patreon
