When a git remote is configured with an absolute path, use that path,
rather than making it relative. If it's configured with a relative path,
use that.
Git.Construct.fromPath changed to preserve the path as-is,
rather than making it absolute. And Annex.new changed to not
convert the path to relative. Instead, Git.CurrentRepo.get
generates a relative path.
A few things that used fromAbsPath unncessarily were changed in passing to
use fromPath instead. I'm seeing fromAbsPath as a security check,
while before it was being used in some cases when the path was
known absolute already. It may be that fromAbsPath is not really needed,
but only git-annex-shell uses it now, and I'm not 100% sure that there's
not some input that would cause a relative path to be used, opening a
security hole, without the security check. So left it as-is.
Test suite passes and strace shows the configured remote url is used
unchanged in the path into it. I can't be 100% sure there's not some code
somewhere that takes an absolute path to the repo and converts it to
relative and uses it, but it seems pretty unlikely that the code paths used
for a git remote would call such code. One place I know of is gitAnnexLink,
but I'm pretty sure that git remotes never deal with annex symlinks. If
that did get called, it generates a path relative to cwd, which would have
been wrong before this change as well, when operating on a remote.
When annex.stalldetection is not enabled, and a likely stall is detected,
display a suggestion to enable it.
Note that the progress meter display is not taken down when displaying
the message, so it will display like this:
0% 8 B 0 B/s
Transfer seems to have stalled. To handle stalling transfers, configure annex.stalldetection
0% 10 B 0 B/s
Although of course if it's really stalled, it will never update
again after the message. Taking down the progress meter and starting
a new one doesn't seem too necessary given how unusual this is,
also this does help show the state it was at when it stalled.
Use of uninterruptibleCancel here is ok, the thread it's canceling
only does STM transactions and sleeps. The annex thread that gets
forked off is separate to avoid it being canceled, so that it
can be joined back at the end.
A module cycle required moving from dupState the precaching of the
remote list. Doing it at startConcurrency should cover all the cases
where the remote list is used in concurrent actions.
This commit was sponsored by Kevin Mueller on Patreon.
annex.stalldetection can now be set to "true" to make git-annex do
automatic stall detection when it detects a remote is updating its transfer
progress consistently enough.
This commit was sponsored by Luke Shumaker on Patreon.
Note this does find things in PATH that are not executable.
Like searchPath use, the executable bit is not checked. Thing is,
there does not seem to be a binding for access(), which would be the
right way to check that the right execute bit is set. Anyway, if it's in
PATH and it's a file, it's probably fine to treat it as something that
was intended to be executable.
This commit was sponsored by Brock Spratlen on Patreon.
Seems only fair, that, like git runs git-annex, git-annex runs
git-annex-foo.
Implementation relies on O.forwardOptions, so that any options are passed
through to the addon program. Note that this includes options before the
subcommand, eg: git-annex -cx=y foo
Unfortunately, git-annex eats the --help/-h options.
This is because it uses O.hsubparser, which injects that option into each
subcommand. Seems like this should be possible to avoid somehow, to let
commands display their own --help, instead of the dummy one git-annex
displays.
The two step searching mirrors how git works, it makes finding
git-annex-foo fast when "git annex foo" is run, but will also support fuzzy
matching, once findAllAddonCommands gets implemented.
This commit was sponsored by Dr. Land Raider on Patreon.
