Complicated by such repositories potentially being repos that should have
an annex.uuid, but it failed to be gotten, perhaps due to the past ssh repo
setup bugs. This is handled now by an Upgrade Repository button.
When starting up the assistant, it'll remind about the current
repository, if it doesn't have checks. And when a removable drive
is plugged in, it will remind if a repository on it lacks checks.
Since that might be annoying, the reminders can be turned off.
This commit was sponsored by Nedialko Andreev.
A file named "foo-" or "foo-bar" was taken as a key's file, with a backend
of "foo", and an empty keyName. This led to various problems, especially
because converting that key back to a file did not yeild the same filename.
Currently only implemented for local git remotes. May try to add support
to git-annex-shell for ssh remotes later. Could concevably also be
supported by some special remote, although that seems unlikely.
Cronner user this when available, and when not falls back to
fsck --fast --from remote
git annex fsck --from does not itself use this interface.
To do so, I would need to pass --fast and all other options that influence
fsck on to the git annex fsck that it runs inside the remote. And that
seems like a lot of work for a result that would be no better than
cd remote; git annex fsck
This may need to be revisited if git-annex-shell gets support, since it
may be the case that the user cannot ssh to the server to run git-annex
fsck there, but can run git-annex-shell there.
This commit was sponsored by Damien Diederen.
To support this, a core.gcrypt-id is stored by git-annex inside the git
config of a local gcrypt repository, when setting it up.
That is compared with the remote's cached gcrypt-id. When different, a
drive has been changed. git-annex then looks up the remote config for
the uuid mapped from the core.gcrypt-id, and tweaks the configuration
appropriately. When there is no known config for the uuid, it will refuse to
use the remote.
This is a git-remote-gcrypt encrypted special remote. Only sending files
in to the remote works, and only for local repositories.
Most of the work so far has involved making initremote work. A particular
problem is that remote setup in this case needs to generate its own uuid,
derivied from the gcrypt-id. That required some larger changes in the code
to support.
For ssh remotes, this will probably just reuse Remote.Rsync's code, so
should be easy enough. And for downloading from a web remote, I will need
to factor out the part of Remote.Git that does that.
One particular thing that will need work is supporting hot-swapping a local
gcrypt remote. I think it needs to store the gcrypt-id in the git config of the
local remote, so that it can check it every time, and compare with the
cached annex-uuid for the remote. If there is a mismatch, it can change
both the cached annex-uuid and the gcrypt-id. That should work, and I laid
some groundwork for it by already reading the remote's config when it's
local. (Also needed for other reasons.)
This commit was sponsored by Daniel Callahan.
Cipher is now a datatype
data Cipher = Cipher String | MacOnlyCipher String
which makes more precise its interpretation MAC-only vs. MAC + used to
derive a key for symmetric crypto.
With the initremote parameters "encryption=pubkey keyid=788A3F4C".
/!\ Adding or removing a key has NO effect on files that have already
been copied to the remote. Hence using keyid+= and keyid-= with such
remotes should be used with care, and make little sense unless the point
is to replace a (sub-)key by another. /!\
Also, a test case has been added to ensure that the cipher and file
contents are encrypted as specified by the chosen encryption scheme.
When quvi is installed, git-annex addurl automatically uses it to detect
when an page is a video, and downloads the video file.
web special remote: Also support using quvi, for getting files,
or checking if files exist in the web.
This commit was sponsored by Mark Hepburn. Thanks!
Introduced a new per-remote option 'annex-rsync-transport' to specify
the remote shell that it to be used with rsync. In case the value is
'ssh', connections are cached unless 'sshcaching' is unset.
Most remotes have meters in their implementations of retrieveKeyFile
already. Simply hooking these up to the transfer log makes that information
available. Easy peasy.
This is particularly valuable information for encrypted remotes, which
otherwise bypass the assistant's polling of temp files, and so don't have
good progress bars yet.
Still some work to do here (see progressbars.mdwn changes), but this
is entirely an improvement from the lack of progress bars for encrypted
downloads.
* since this is a crippled filesystem anyway, git-annex doesn't use
symlinks on it
* so there's no reason to use the mixed case hash directories that we're
stuck using to avoid breaking everyone's symlinks to the content
* so we can do what is already done for all bare repos, and make non-bare
repos on crippled filesystems use the all-lower case hash directories
* which are, happily, all 3 letters long, so they cannot conflict with
mixed case hash directories
* so I was able to 100% fix this and even resuming `git annex add` in the
test case will recover and it will all just work.
Let's make semitrusted+:1 mean that, since it cannot be expressed easily
with the current syntax (could use (semitrusted:1 or trusted:1), but that
does not scale to higher values than 2 copy, and also fails if I add more
trust levels).
Thanks to Andy for spotting this bug by just reading my blog.
I would have sort of liked to put this in .gitattributes, but it seems
it does not support multi-word attribute values. Also, making this a single
config setting makes it easy to only parse the expression once.
A natural next step would be to make the assistant `git add` files that
are not annex.largefiles. OTOH, I don't think `git annex add` should
`git add` such files, because git-annex command line tools are
not in the business of wrapping git command line tools.
There was confusion in different parts of the progress bar code about
whether an update contained the total number of bytes transferred, or the
number of bytes transferred since the last update. One way this bug
showed up was progress bars that seemed to stick at zero for a long time.
In order to fix it comprehensively, I add a new BytesProcessed data type,
that is explicitly a total quantity of bytes, not a delta.
Note that this doesn't necessarily fix every problem with progress bars.
Particularly, buffering can now cause progress bars to seem to run ahead
of transfers, reaching 100% when data is still being uploaded.
