In indirect mode, now checks the inode cache to detect changes to a file.
Note that a file can still be changed if a process has it open for write,
after landing in the annex.
In direct mode, some checking of the inode cache was done before, but
from a much later point, so fewer modifications could be detected. Now it's
as good as indirect mode.
On crippled filesystems, no lock down is done before starting to add a
file, so checking the inode cache is the only protection we have.
git annex init probes for crippled filesystems, and sets direct mode, as
well as `annex.crippledfilesystem`.
Avoid manipulating permissions of files on crippled filesystems.
That would likely cause an exception to be thrown.
Very basic support in Command.Add for cripped filesystems; avoids the lock
down entirely since doing it needs both permissions and hard links.
Will make this better soon.
New setting, can be used to disable autocommit of changed files by the
assistant, while it still does data syncing and other tasks.
Also wired into webapp UI
Now there's a Config type, that's extracted from the git config at startup.
Note that laziness means that individual config values are only looked up
and parsed on demand, and so we get implicit memoization for all of them.
So this is not only prettier and more type safe, it optimises several
places that didn't have explicit memoization before. As well as getting rid
of the ugly explicit memoization code.
Not yet done for annex.<remote>.* configuration settings.
* Bugfix: Remove leading \ from checksums output by sha*sum commands,
when the filename contains \ or a newline. Closes: #696384
* fsck: Still accept checksums with a leading \ as valid, now that
above bug is fixed.
* migrate: Remove leading \ in checksums
Monitors git-annex branch for changes, which are noticed by the Merger
thread whenever the branch ref is changed (either due to an incoming push,
or a local change), and refreshes cached config values for modified config
files.
Rate limited to run no more often than once per minute. This is important
because frequent git-annex branch changes happen when files are being
added, or transferred, etc.
A primary use case is that, when preferred content changes are made,
and get pushed to remotes, the remotes start honoring those settings.
Other use cases include propigating repository description and trust
changes to remotes, and learning when a remote has added a new special
remote, so the webapp can present the GUI to enable that special remote
locally.
Also added a uuid.log cache. All other config files already had caches.
When there's just 1 client repo, and a transfer repo is created, its
preferred content will now make it prefer all content in the client,
even though there's no other client yet to transfer it to. Presumably,
another client will be created eventually. It might even already exist,
and the transfer repo will be used to connect up with it.
Incomplete; I need to finish parsing and saving. This will also be used
for editing transfer control expresssions.
Removed the group display from the status output, I didn't really
like that format, and vicfg can be used to see as well as edit rempository
group membership.
Transfer info files are updated when the callback is called, updating
the number of bytes transferred.
Left unused p variables at every place the callback should be used.
Which is rather a lot..
Currently only the web special remote is readonly, but it'd be possible to
also have readonly drives, or other remotes. These are handled in the
assistant by only downloading from them, and never trying to upload to
them.
This commit includes a paydown on technical debt incurred two years ago,
when I didn't know that it was bad to make custom Read and Show instances
for types. As the routes need Read and Show for Transfer, which includes a
Key, and deriving my own Read instance of key was not practical,
I had to finally clean that up.
So the compact Key read and show functions are now file2key and key2file,
and Read and Show are now derived instances.
Changed all code that used the old instances, compiler checked.
(There were a few places, particularly in Command.Unused, and the test
suite where the Show instance continue to be used for legitimate
comparisons; ie show key_x == show key_y (though really in a bloom filter))
In order to record a semi-useful filename associated with the key,
this required plumbing the filename all the way through to the remotes'
storeKey and retrieveKeyFile.
Note that there is potential for deadlock here, narrowly avoided.
Suppose the repos are A and B. A sends file foo to B, and at the same
time, B gets file foo from A. So, A locks its upload transfer info file,
and then locks B's download transfer info file. At the same time,
B is taking the two locks in the opposite order. This is only not a
deadlock because the lock code does not wait, and aborts. So one of A or
B's transfers will be aborted and the other transfer will continue.
Whew!
Kqueue needs to remember which files failed to be added due to being open,
and retry them. This commit gets the data in place for such a retry thread.
Broke KeySource out into its own file, and added Eq and Ord instances
so it can be stored in a Set.
This option avoids gpg key distribution, at the expense of flexability, and
with the requirement that all clones of the git repository be equally
trusted.
A bit tricky to avoid printing it twice in a row when there are queued git
commands to run and journal to stage.
Added a generic way to run an action that may output multiple side
messages, with only the first displayed.
