This is a git-remote-gcrypt encrypted special remote. Only sending files
in to the remote works, and only for local repositories.
Most of the work so far has involved making initremote work. A particular
problem is that remote setup in this case needs to generate its own uuid,
derivied from the gcrypt-id. That required some larger changes in the code
to support.
For ssh remotes, this will probably just reuse Remote.Rsync's code, so
should be easy enough. And for downloading from a web remote, I will need
to factor out the part of Remote.Git that does that.
One particular thing that will need work is supporting hot-swapping a local
gcrypt remote. I think it needs to store the gcrypt-id in the git config of the
local remote, so that it can check it every time, and compare with the
cached annex-uuid for the remote. If there is a mismatch, it can change
both the cached annex-uuid and the gcrypt-id. That should work, and I laid
some groundwork for it by already reading the remote's config when it's
local. (Also needed for other reasons.)
This commit was sponsored by Daniel Callahan.
I thought at first this was a Windows specific problem, but it's not;
this affects checking any non-bare repository exported via http. Which is
a potentially important use case!
The actual bug was the case where Right False was returned by the first url
short-curcuited later checks. But the whole method used felt like code
I'd no longer write, and the use of undefined was particularly disgusting.
So I rewrote it.
Also added an action display.
This commit was sponsored by Eric Hanchrow. Thanks!
annexLocations uses OS-native directory separators, but for an url,
it needs to use / even on Windows.
This is an ugly workaround. Could parameterize a lot of stuff in
annexLocations to fix it better. I suspect this is probably the only place
it's needed though.
Made fromDirect check that a file in the tree has good content (and is not
a broken symlink either) before copying it to another file that has the
same key.
Made replaceFile clean up the temp file if the action that creates it, or
the file replacement action fails.
Most remotes have meters in their implementations of retrieveKeyFile
already. Simply hooking these up to the transfer log makes that information
available. Easy peasy.
This is particularly valuable information for encrypted remotes, which
otherwise bypass the assistant's polling of temp files, and so don't have
good progress bars yet.
Still some work to do here (see progressbars.mdwn changes), but this
is entirely an improvement from the lack of progress bars for encrypted
downloads.
* since this is a crippled filesystem anyway, git-annex doesn't use
symlinks on it
* so there's no reason to use the mixed case hash directories that we're
stuck using to avoid breaking everyone's symlinks to the content
* so we can do what is already done for all bare repos, and make non-bare
repos on crippled filesystems use the all-lower case hash directories
* which are, happily, all 3 letters long, so they cannot conflict with
mixed case hash directories
* so I was able to 100% fix this and even resuming `git annex add` in the
test case will recover and it will all just work.
There was confusion in different parts of the progress bar code about
whether an update contained the total number of bytes transferred, or the
number of bytes transferred since the last update. One way this bug
showed up was progress bars that seemed to stick at zero for a long time.
In order to fix it comprehensively, I add a new BytesProcessed data type,
that is explicitly a total quantity of bytes, not a delta.
Note that this doesn't necessarily fix every problem with progress bars.
Particularly, buffering can now cause progress bars to seem to run ahead
of transfers, reaching 100% when data is still being uploaded.
This got broken in commit e9238e9588.
I observed a key that had been copied to a remote, but the location
log was out of date, and due to this bug, git annex transferkey failed
and so the file could not be dropped when it was moved to an archive
directory.
Pass subcommand as a regular param, which allows passing git parameters
like -c before it. This was already done in the pipeing set of functions,
but not the command running set.
In general, git-annex does not try to preserve file permissions. For
example, they don't round trip through special remotes. So it's ok to not
preserve them for git remotes either.
On crippled filesystems, rsync has been observed failing after the file
was transferred because it couldn't set some permission or other.
However, I don't yet have a reliable way to deal with files being modified
while they're being transferred. I have code that detects it on the sending
side, but the receiver is still free to move the wrong content into its
annex, and record that it has the content. So that's not acceptable, and
I'll need to work on it some more.
However, at this point I can use a direct mode repository as a remote and
transfer files from and to it.
Aka solve the github problem.
Note that it's possible the initial configlist will fail for some network
reason etc, and then the fetch succeeds. In this case, a usable remote gets
disabled. But it does print a message, and this only happens once per
remote, so that seems ok.
When a transfer fails, the progress info can be used to intelligently
retry it. If the transfer managed to make some progress, but did not
fully complete, then there's a good chance that a retry will finish it
(or at least make more progress).
cp is used here, but we can just watch the size of the destination file
This commit made from within the ruins of an old mill, overlooking a
beautiful waterfall.
Current implementation parses rsync's output a character a time, which
is hardly efficient. It could be sped up a lot by using hGetBufSome,
but that would require going really lowlevel, down to raw C style buffers
(good example of that here: http://users.aber.ac.uk/afc/stricthaskell.html)
But rsync doesn't output very much, so currently it seems ok.
Transfer info files are updated when the callback is called, updating
the number of bytes transferred.
Left unused p variables at every place the callback should be used.
Which is rather a lot..
Turns out that recvkey already does this same check. This avoids a transfer
file being created for the download that never happened, which in turn
will avoid the assistant seeing that the download has finished, when no
transfer actually took place.
Currently only the web special remote is readonly, but it'd be possible to
also have readonly drives, or other remotes. These are handled in the
assistant by only downloading from them, and never trying to upload to
them.
This commit includes a paydown on technical debt incurred two years ago,
when I didn't know that it was bad to make custom Read and Show instances
for types. As the routes need Read and Show for Transfer, which includes a
Key, and deriving my own Read instance of key was not practical,
I had to finally clean that up.
So the compact Key read and show functions are now file2key and key2file,
and Read and Show are now derived instances.
Changed all code that used the old instances, compiler checked.
(There were a few places, particularly in Command.Unused, and the test
suite where the Show instance continue to be used for legitimate
comparisons; ie show key_x == show key_y (though really in a bloom filter))
Make Utility.Process wrap the parts of System.Process that I use,
and add debug logging to them.
Also wrote some higher-level code that allows running an action
with handles to a processes stdin or stdout (or both), and checking
its exit status, all in a single function call.
As a bonus, the debug logging now indicates whether the process
is being run to read from it, feed it data, chat with it (writing and
reading), or just call it for its side effect.
Test suite now passes with -threaded!
I traced back all the hangs with -threaded to System.Cmd.Utils. It seems
it's just crappy/unsafe/outdated, and should not be used. System.Process
seems to be the cool new thing, so converted all the code to use it
instead.
In the process, --debug stopped printing commands it runs. I may try to
bring that back later.
Note that even SafeSystem was switched to use System.Process. Since that
was a modified version of code from System.Cmd.Utils, it needed to be
converted too. I also got rid of nearly all calls to forkProcess,
and all calls to executeFile, which I'm also doubtful about working
well with -threaded.
This *almost* works.
Along the way, I noticed that the --uuid parameter was being accidentially
passed after the --, so that has never been actually used by
git-annex-shell to verify it's running in the expected repository. Oops. Fixed.
In order to record a semi-useful filename associated with the key,
this required plumbing the filename all the way through to the remotes'
storeKey and retrieveKeyFile.
Note that there is potential for deadlock here, narrowly avoided.
Suppose the repos are A and B. A sends file foo to B, and at the same
time, B gets file foo from A. So, A locks its upload transfer info file,
and then locks B's download transfer info file. At the same time,
B is taking the two locks in the opposite order. This is only not a
deadlock because the lock code does not wait, and aborts. So one of A or
B's transfers will be aborted and the other transfer will continue.
Whew!
Not including such remotes turned out to have other consequences,
including annex-truselevel git config being ignored. Instead, add guards
before each operation that might try to operate on such a repo.
Prelude.undefined error message was introduced by
bb4f31a0ee.
It seems best to filter out local repositories that cannot be accessed
from the list of remotes, rather than keeping them in and making every
thing that uses the list have to deal with remotes that may have an unknown
location.
Besides fixing the error message, this also makes unavailable local
remotes' names not be shown in various messages, including in git annex
status output.
Also, move --to an unavailable local repository now avoids some ugly
errors like "changeWorkingDirectory: does not exist".
This was shown redundantly for a tricky reason -- while it runs
inside a doSideAction block that would appear to supress it,
the action being run is in a different state monad; for the remote,
and so the suppression doesn't work.
Always suppressing the message when committing to a local remote is
ok do to though -- it mirrors the /dev/nulling of the git annex shell commit
output. And it turns out that any time there is a git-annex branch state
change to commit on the remote, the local repo has also had a similar
change made, and so the message has been shown already.
The environment needs to override git-config. Changed when git config is
read, and avoid rereading it once it's been read.
chdir for both worktree settings.
getConfig got a remote-specific config, and this confusing name caused it
to be used a couple of places that only were interested in global configs.
Rename to getRemoteConfig and make getConfig only get global configs.
There are no behavior changes here, but remote.<name>.annex-web-options
never actually worked (and per-remote web options is a very unlikely to be
useful case so I didn't make it work), so fix the documentation for it.
openSUSE patches rsync with a patch adding SIP protocol support.
https://gist.github.com/2026167
With this patch, running rsync with no hostname parameter is apparently
supposed to list SIP hosts on the network. Practically, it does nothing
and exits 0.
git-annex uses rsync in a very special way to allow git-annex-shell to be
run on the remote host, and so did not need to specify a hostname, or a
file to transfer as a rsync parameter. So it sent ":", a degenerate case of
"host:file".
But the patch cannot differentiate ":" with no host parameter
(a bug in the SIP patch surely).
Results were that getting files failed, as rsync seemed to succeed, but the
requested file failed to arrive. Also I think that sending files will
make git-annex think a file has been transferred to the remote when
really rsync does nothing.
The workaround for this buggy rsync patch is to use "dummy:" as the
hostname.
Added Annex.cleanup, which is a general purpose interface for adding
actions to run at the end.
Remotes with the old git-annex-shell will commit every time, and have no
commit command, so hide stderr when running the commit command.
If there's no Content-Length, or the key has no size, this check is not
done, but it should happen most of the time, and protect against web
content that has changed.
Done by adding a oneshot mode, in which location log changes are written to
the journal, but not committed. Taking advantage of git-annex's existing
ability to recover in this situation.
This is used by git-annex-shell and other places where changes are made to
a remote's location log.
For a local git remote, can symlink the file.
For a git remote using rsync, can preseed any local content.
There are a few reasons to use fsck --from on a normal git remote.
One is if it's using gitosis or similar, and you don't have shell access
to run git annex locally. Another reason could be if you just want to
fsck certian files of a bare remote.
With --fast, unavailable local remotes are filtered out of the fast set.
This way, if there are local remotes, --fast always acts only on them,
and if none are mounted, acts on nothing. This consistency is better
than --fast acting on different remotes depending on what's mounted.
A crash on parsing was fixed a while ago. This adds support for fully
correctly parsing multiline git config values, using git config --null.
Since git-annex-shell configlist uses normal git config output, I left in
support for that too; the two forms of config output can be easily
identified by the parser. Since configlist only prints the annex.uuid
config, there's no risk of multiline values there, so no need to change it.
Needed due to this scenario: Bare repo origin is made, foo is cloned from it;
foo is initalized; a file is added to foo's annex; git annex move --to origin
Since the git-annex branch has not yet been pushed to origin, it doesn't
auto-initialize. When the content is sent to it, it's stored, but
the remote has NoUUID, and so nothing is logged in the location log.
Then the content is removed from the local repo, and git-annex has lost
track of it.
git annex fsck in origin will find the lost content, but let's not let this
happen. Content should only be sent to initalized remotes.
This cannot happen for non-local remotes, since git-annex-shell always
checks that the repo is initialized.
Supporting multiple directory hash types will allow converting to a
different one, without a flag day.
gitAnnexLocation now checks which of the possible locations have a file.
This means more statting of files. Several places currently use
gitAnnexLocation and immediately check if the returned file exists;
those need to be optimised.
git-annex-shell inannex now returns always 0, 1, or 100 (the last when
it's unclear if content is currently in the index due to it currently being
moved or dropped).
(Actual locking code still not yet written.)
Many functions took the repo as their first parameter. Changing it
consistently to be the last parameter allows doing some useful things with
currying, that reduce boilerplate.
In particular, g <- gitRepo is almost never needed now, instead
use inRepo to run an IO action in the repo, and fromRepo to get
a value from the repo.
This also provides more opportunities to use monadic and applicative
combinators.
Before the config was read each time onLocal was called, and entirely
redundantly since it's read for same-host remotes on startup.
Also a minor bug fix: When rsyncing to a same-host remote, use the
rsync-options from the repository that the user ran git-annex in, not those of
the receiving repository.
Specifically, disabled trying to update the git-annex branch on the remote,
since that data is never used by operations that act on such remotes.
Also, when copying content to such a remote, skip committing the presence
information changes to its git-annex branch. Leaving it in the journal there
is ok: Any command run on the remote that needs the info will flush the
journal.
This may partially solve this bug:
http://git-annex.branchable.com/bugs/fails_to_handle_lot_of_files/
Although I still see unreaped git processes piling up when doing a copy --to.
Only one place need to filter the list of remotes for ignored remotes:
keyPossibilities. Make the full list available to everything else.
This allows getting rid of the special case handing for --from and --to
to make ignored remotes not be ignored with those options.
The only remaining vestiage of backends is different types of keys. These
are still called "backends", mostly to avoid needing to change user interface
and configuration. But everything to do with storing keys in different
backends was gone; instead different types of remotes are used.
In the refactoring, lots of code was moved out of odd corners like
Backend.File, to closer to where it's used, like Command.Drop and
Command.Fsck. Quite a lot of dead code was removed. Several data structures
became simpler, which may result in better runtime efficiency. There should
be no user-visible changes.
Otherwise, the location log changes are only staged in its index,
and this can confuse matters if pulling or cloning from the remote.
The test suite was failing because this wasn't done.
cp is still used when copying file from repos on the same filesystem, since
--reflink=auto can make it significantly faster on filesystems such as
btrfs.
Directory special remotes still use cp, not rsync. It's not clear what
tmp file should be used when rsyncing to such a remote.
Fully tested and working, including resuming and encryption. (Though not
resuming when sending *with* encryption; gpg doesn't produce identical
output each time.)
Uses same layout as the directory special remote and the .git/annex/objects/
directory.
Since the queue is flushed in between subcommand actions being run,
there should be no issues with actions that expect to queue up some stuff
and have it run after they do other stuff. So I didn't have to audit for
such assumptions.