device/device-asus-me176c:
- Install me176c-factory to apply correct MAC addresses for
WiFi and BT
- Use FAT32 for boot partition. This allows flashing the boot
partition directly as ESP (EFI System Partition).
- Overall cleanup
device/linux-asus-me176c:
- Update kernel fork to 4.19.80
- Cleanup APKBUILD
- Stop building patched ACPI DSDT table directly into kernel
firmware/firmware-asus-me176c:
- Package WiFi firmware
firmware/firmware-asus-me176c-acpi:
- New package for the patched ACPI DSDT table
-> Separate from firmware-asus-me176c because it is always required,
(not optional)
[ci:skip-build]: runs into timeout
The modem boots up properly without causing any problems, so let's
install the firmware and support packages by default.
Also install adsp-audio now by default to boot up the adsp for audio and
other services provided by the processor.
[ci:skip-build]: already built successfully in CI
The initramfs needs ext4 (to mount the rootfs) and usb_f_rndis
(to enable USB networking on devices that use USB configfs).
If these are built as modules, they need to be included in initramfs.
[ci:skip-build]: already built successfully in CI
We have linux-postmarketos-qcom and linux-postmarketos-qcom-msm8916 now,
which is quite confusing. linux-postmarketos-qcom was originally added
for MSM8974 devices (e.g. Nexus 5) and its patches on top of mainline
are therefore quite focused on MSM8974.
linux-postmarketos-qcom-msm8916 on the other hand, has patches specific
to MSM8916. The two packages do not have any patch in common, therefore
merging the two would only cause signficiant overhead to coordinate
testing for devices of the two SoCs.
Therefore, it is better to keep them separate.
To avoid confusion, rename linux-postmarketos-qcom to
linux-postmarketos-qcom-msm8974 to make it clear that it is really
a close-to-mainline kernel for MSM8974 devices.
[ci:skip-build]: already built successfully in CI
The sparse image tools (img2simg, simg2img, append2simg) are now
part of Alpine's android-tools package where they are continously
updated. (See https://github.com/nmeum/android-tools/pull/8)
Remove "libsparse" as depends from all packages because it is either:
- installed automatically by pmbootstrap when needed for
deviceinfo_flash_sparse="true"
(device-chuwi-hi10plus, device-htc-flounder, device-lg-bullhead,
device-semc-anzu, device-xiaomi-kenzo)
- seemingly unused(?)
(device-asus-z00t, linux-motorola-falcon, linux-motorola-peregrine)
[ci:skip-build]: already built successfully in CI
in Librem 5 devkit, card0 is coming from etnaviv and is not usable for
kms/drm. So force usage of card1 for kwin_wayland.
[ci:skip-build]: won't finish in time
This simplifies the uboot script and updates it to use correct address
offsets for kernel, ramdisk and fdt. Appending the dtb to the kernel is
no longer necessary. This also changes the dtb to the one used on
PureOS.
linux-samsung-apexq/APKBUILD updated with newer kernel commit
sha from d2 repo, and now builds and packages modules into the
rootfs in /lib/modules/. prima wifi module not yet working.
The subpackage depends on the "kernel-scripts" package, which has been
removed from pmaports.git. Therefore the -dev package could not be
installed, and our CI check of the binary repo noticed this and was
failing.
Related: https://gitlab.com/postmarketOS/pmaports/merge_requests/329
Make the renamed pine packages build again, by giving their post-install
files the new pkgname.
(So much for trivial package renames, needs better testing next time :p)
* Added display in final pinephone to the kernel
* Added getty
* Use RGB led to signify booting status in u-boot
* Enable CONFIG_GPIO_SYSFS
[ci:skip-build]: won't finish in time
Changes in the kernel defconfig:
- disable ANDROID_PARANOID_NETWORK (removes network restrictions)
- enable CONFIG_USB_G_ANDROID and CONFIG_DIAG_CHAR (for USB networking)
- enable DEVTMPFS (needed for udev -> touch support in weston)
- enable FB_MSM_DEFAULT_DEPTH_RGB565 (for 16-bit support to avoid red
screen)
- enable SYSVIPC (so busybox' syslogd can log to a ringbuffer in the
kernel)
- enable VT (for virtual terminal over USB)
[ci:skip-build]: already built successfully in CI
Insert missing space into the depends line, so it reads "gmp-dev bash"
instead of "gmp-devbash". This did not cause a build failure, but made
the upstream compat CI check fail after the binary package had been
built and uploaded. It would also cause an error if one tried to install
the package. The CI check will pass once the fixed package is built and
uploaded.
[ci:skip-build]
* add dev-package
* modularize some kernel drivers
* modernize Makefile to silence some warnings
* fix various warnings
* add some CVE patches
[ci:skip-build]: already built successfully in CI
This rebases the Pixel 3 XL patches on top of Linux 5.3-rc5.
Also enabled more kernel modules related to modem, and applied
Bjorn Andersson's patch for resetting the UFS memory.
See
https://gitlab.com/postmarketOS/pmaports/issues/153
for more information.
[ci:skip-build] because kernel takes more than one hour to build
Some Samsung muic's have debug possibility, but seems kernel config
option for that was deleted. Muic debug can be useful for attaching UART
cable to phone.
[ci:skip-build]: already built successfully in CI
Firmware for Exynos 7880 SOC from https://github.com/TheMuppets
It is needed to enable wifi, and possibly other hardware. All of firmware found on Muppets has been packaged.
Also contains wlan module configuration.
Use deviceinfo_framebuffer_landscape during splash screen generation.
Also add the postmarketos-splash arguments variable to the computation
of the hash for the cache.
Adjust device-pine-pinetab to use the new variable, and therefore rotate
its splash screen.
[ci:skip-build]: already built successfully in CI
- rename 'ch-de' keymap to 'ch' as in X keyboard config file
- add PMOS_NO_OUTPUT_REDIRECT to kernel cmdline (fixes debug-shell)
- add all keymap files in initramfs
- load default us keymap in initramfs
Also fix a few spaces->tabs issues while we're at it.
Should result in the exact same commit being download as before, the
checksum is different because GitHub puts the commit instead of the
branch name into the archive.
[ci:skip-build]: already built successfully in CI
[ci:skip-vercheck]
- OTG support
- Charger
- WiFi 5GHz
- RTC bug "fixed" (always-on interrupt - made device overheat!)
- Kernel version bumped to 5.2.1
- Memory timings
- New WM8994 codec board driver (fixes suspend/resume)
- Camera's regulator supported now (saves power at least!)
- Updated panel driver (still not in mainline, idk why)
- MHL support in kernel (fixes boot times and screen, currently disabled in X,
not tested)
- Other minor kernel chagnes
[ci:skip-build]: already built successfully in CI
