Added --json-error-messages option, which includes error messages in the
json output, rather than outputting them to stderr.
The actual rediretion of errors is not implemented yet, this is only
the docs and option plumbing.
This commit was supported by the NSF-funded DataLad project.
git annex add, git annex lock etc make multiple seek passes,
and each seek pass checked that files existed. That was unncessary
redundant work.
Fixed by adding a new WorkTreeItem type, make seek actions use it,
and check that the files exist when constructing it.
This commit was supported by the NSF-funded DataLad project.
It takes a single key-value backend, rather than the unncessary and confusing list.
The old option still works if set.
Simplified some old old code too.
This commit was sponsored by Thomas Hochstein on Patreon.
This only adds 1 stat to each file fscked for locked files, so
added overhead is minimal.
For unlocked files it has to access the database to see if a file
is modified.
This is a work in progress. It compiles and is able to do basic command
dispatch, including git autocorrection, while using optparse-applicative
for the core commandline parsing.
* Many commands are temporarily disabled before conversion.
* Options are not wired in yet.
* cmdnorepo actions don't work yet.
Also, removed the [Command] list, which was only used in one place.
This fixes all instances of " \t" in the code base. Most common case
seems to be after a "where" line; probably vim copied the two space layout
of that line.
Done as a background task while listening to episode 2 of the Type Theory
podcast.
Only fsck and reinject and the test suite used the Backend, and they can
look it up as needed from the Key. This simplifies the code and also speeds
it up.
There is a small behavior change here. Before, all commands would warn when
acting on an annexed file with an unknown backend. Now, only fsck and
reinject show that warning.
I've been disliking how the command seek actions were written for some
time, with their inversion of control and ugly workarounds.
The last straw to fix it was sync --content, which didn't fit the
Annex [CommandStart] interface well at all. I have not yet made it take
advantage of the changed interface though.
The crucial change, and probably why I didn't do it this way from the
beginning, is to make each CommandStart action be run with exceptions
caught, and if it fails, increment a failure counter in annex state.
So I finally remove the very first code I wrote for git-annex, which
was before I had exception handling in the Annex monad, and so ran outside
that monad, passing state explicitly as it ran each CommandStart action.
This was a real slog from 1 to 5 am.
Test suite passes.
Memory usage is lower than before, sometimes by a couple of megabytes, and
remains constant, even when running in a large repo, and even when
repeatedly failing and incrementing the error counter. So no accidental
laziness space leaks.
Wall clock speed is identical, even in large repos.
This commit was sponsored by an anonymous bitcoiner.
* since this is a crippled filesystem anyway, git-annex doesn't use
symlinks on it
* so there's no reason to use the mixed case hash directories that we're
stuck using to avoid breaking everyone's symlinks to the content
* so we can do what is already done for all bare repos, and make non-bare
repos on crippled filesystems use the all-lower case hash directories
* which are, happily, all 3 letters long, so they cannot conflict with
mixed case hash directories
* so I was able to 100% fix this and even resuming `git annex add` in the
test case will recover and it will all just work.
In indirect mode, now checks the inode cache to detect changes to a file.
Note that a file can still be changed if a process has it open for write,
after landing in the annex.
In direct mode, some checking of the inode cache was done before, but
from a much later point, so fewer modifications could be detected. Now it's
as good as indirect mode.
On crippled filesystems, no lock down is done before starting to add a
file, so checking the inode cache is the only protection we have.
* Bugfix: Remove leading \ from checksums output by sha*sum commands,
when the filename contains \ or a newline. Closes: #696384
* fsck: Still accept checksums with a leading \ as valid, now that
above bug is fixed.
* migrate: Remove leading \ in checksums
Kqueue needs to remember which files failed to be added due to being open,
and retry them. This commit gets the data in place for such a retry thread.
Broke KeySource out into its own file, and added Eq and Ord instances
so it can be stored in a Set.
Now gitattributes are looked up, efficiently, in only the places that
really need them, using the same approach used for cat-file.
The old CheckAttr code seemed very fragile, in the way it streamed files
through git check-attr.
I actually found that cad8824852
was still deadlocking with ghc 7.4, at the end of adding a lot of files.
This should fix that problem, and avoid future ones.
The best part is that this removes withAttrFilesInGit and withNumCopies,
which were complicated Seek methods, as well as simplfying the types
for several other Seek methods that had a Backend tupled in.
Supporting multiple directory hash types will allow converting to a
different one, without a flag day.
gitAnnexLocation now checks which of the possible locations have a file.
This means more statting of files. Several places currently use
gitAnnexLocation and immediately check if the returned file exists;
those need to be optimised.
Many functions took the repo as their first parameter. Changing it
consistently to be the last parameter allows doing some useful things with
currying, that reduce boilerplate.
In particular, g <- gitRepo is almost never needed now, instead
use inRepo to run an IO action in the repo, and fromRepo to get
a value from the repo.
This also provides more opportunities to use monadic and applicative
combinators.
This new approach allows filtering out checks from the default set that are
not appropriate for a command, rather than having to list every check
that is appropriate. It also reduces some boilerplate.
Haskell does not define Eq for functions, so I had to go a long way around
with each check having a unique id. Meh.
