TF201 nvram was updated since previous did not work on some devices.
Added support for TF101, TF300TG and TF300TL.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Gummiboot was dropped from Alpine. Switch to grub, which is what we use
for tablet-x86uefi too.
In contrary to tablet-x86uefi, run the grub-mkimage command directly
inside the device package:
* This avoids creating another confusing grub-x86 like package (looks
like the x86 version of alpine's grub package, as it's the case with
grub-efi-x86, but actually it is just the result of grub-mkimage).
* In contrary to grub-efi-x86, the resulting efi file is not shared
across several devices.
* It's consistent with uboot mkimage commands, which we also run in
device packages.
Related: 398b7aef0b
Ported succesfully to armv7. Everything that worked on armhf
works on armv7 as well: touch, wifi, usb networking etc.
SWRast (gallium) was not enabled but is needed because the device
does not support 3D acceleration yet.
This is required for kernels earlier than 4.7 for bwrap to work for
normal users, and therefore for gnome web (epiphany) and flatpak.
[ci:skip-build] [ci:ignore-count]
uboot-tools is provided by u-boot-tools but sometimes apk still gets
confused. This change prevents errors such as
pine64-pinephone:~$ sudo apk upgrade --verbose
WARNING: Failed to perform initial self-upgrade, continuing with full upgrade.
ERROR: unable to select packages:
uboot-tools (virtual):
provided by: u-boot-tools
required by: device-pine64-pinephone-0.25-r1[uboot-tools]
[ci:ignore-count]
[ci:skip-build]: already built in CI successfully
The AP6359SA is a BCM4359 SDIO-based Wi-Fi/Bluetooth module that PINE64
sells specifically for the ROCKPro64 device. This commit starts a
firmware package to support it specifically, while others can later add
firmware for other modules sold for the device. Also add this package as
a nonfree subpackage dependency in the ROCKPro64 device APKBUILD.
I was unable to find a suitable license for the firmware blobs, so until
we find a suitable repository containing all of the required files by
the module with a license included, or contact the vendor directly,
let's use LibreELEC's repository without a license for now.
[ci:skip-build]: already built successfully in CI
modules-load.conf was completely unused by this package,
not installed anywhere. brcmfmac is loaded automatically anyway.
Sort values in sources= alphabetically
This is needed with the 5.11 kernel. Also adjust the vram & cma sizes
for all msm8974 devices.
The CMA size is 256MB as set in the kernel config.
VRAM is default 16MB although it is set to 192MB with a kernel patch;
but set it manually for all devices to make it possible to remove this
patch in the future - until we have IOMMU working.
still missing:
* audio
* lcd backlight control
* touchscreen driver
* front camera
* accelerometer mount fix (driver seem not to support mount-matrix)
* 3D acceleration
* HDMI support
New mainline port with most things working (usb/wifi/bt/3d-accel/sound/gps).
Modem/calls/sms/mobile-data should work but couldn't test it recently
due to broken devices.
* Add u-boot build with a lot of patches that makes the display work in
u-boot for boot selection
* Upgrade the rockchip kernel to 5.11 mainline with config for the
rk3399 devices built-in
* Make the rockpro64 and pinebook pro use the newer kernel
[ci:skip-build]
The device has been renamed from fujitsu-m532 to pegatron-chagall since several rebrands of this board exist (Olivetti Olipad3, Siragon 4N, etc.), and Fujitsu M532 is just one of those.
Signed-off-by: Raffaele Tranquillini <raffaele.tranquillini@gmail.com>
Downstream kernel is outdated and no longer maintained by us. Thus,
removed. The linux-xiaomi-beryllium-mainline kernel is removed because
its superseded by the common sdm845 kernel and is no longer needed.
So far the debug-shell in initfs works. The device uses dynamic
partitions, so that has to be figured out to get a proper rootfs.
One thing to look out for is that mount_subpartitions task in initfs
hangs, so pmos_boot=sth was added to kernel cmdline to skip it. This is
also related to dynamic partitions, anyway.
[ci:skip-build] Already built on CI
Cypress bought the brcm WiFi stuff from broadcom so they want their firmware to
be called cyfmac instead of brcmfmac
a lot of brcmfmac firmware is now symlinked to cyfmac
This package is no longer used, as the OnePlus 6 will now use the
linux-postmarketos-qcom-sdm845 package.
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
There is already samsung-a3ulte in community, and the devices actually
share the same kernel, device tree, and basically everything except
firmware. We just need separate firmware packages because Samsung uses
different secure boot certificates on a3lte and a3ulte.
They also share the same wiki page which suggests installation using
the pre-built images now, so having pre-built images only for
samsung-a3ulte is quite confusing for users.
The situation is similar as for samsung-a5ulte and samsung-a5lte
which also are both in community already.
This updates the current commit and refactor APKBUILD to
more modern way of writing downstream kernels. Also move to main/ to fit
other linux-postmarketos-* kernels.
Right now the "bq-picmt" device port is quite confusing.
It's actually for the same device as "bq-paella", which is in community
and uses the mainline kernel, except that it uses the downstream kernel.
Having the downstream kernel packaged is useful for testing sometimes,
but otherwise the device package is completely unsupported.
The mainline port works much better. The downstream port should only
be used if you know what you are doing (e.g. because you want to test
if something is working on downstream but not mainline) and therefore
it should not show up in "pmbootstrap init" by default.
Move the device package to unmaintained to implement that.
Also, add an "# Unmaintained: ..." comment that will be displayed
in "pmbootstrap init" if the device is selected anyway.
This is required by some software, e.g. bluez/gnome to set some ACLs on
/dev/rfkill (see #904). While probably nobody will notice on the
downstream kernels (as we don't have any proper software there anyways)
it's definitely needed on mainline-ish kernels. Surprisingly only one
kernel has broken by enabling this option (linux-sony-tulip) which I've
patched up.
linux-postmarketos-qcom-sdm660 did not break by enabling this option,
but required linux4.17-gcc10-extern_YYLOC_global_declaration.patch to
build again, so this was fixed too.
[ci:skip-build] [ci:ignore-count]
This is a generic package for devices which use x86_64 CPU and 32-bit
EFI. Most distributions don't provide installation for 32-bit EFI, so
installation is not user-friendly.
Actually, these tablets deserve device-specific packages (I am going to
make ones for ASUS VivoTab Note 8 and ASUS Transformer Book T100TA), but
this one includes basic functions and can be booted on any 32-bit EFI
tablet with disabled secure boot and missing device-specific package.
I guess 32-bit EFI with 64-bit CPU is Intel's "feature" and AMD doesn't
have such stuff, so this package will be installed only on devices with
Intel CPU, unlike device-tablet-x64uefi which can be installed on any
x86_64 PC. So i decided to enable some Intel specific things (userspace
GPU stuff and alsa-ucm-conf).
I used for reference device-tablet-x64uefi and
device-trekstor-surftabduow1 packages. This package also can be used as
a reference for device-specific ones.
Added support for Motorola Moto E 2014 codename: condor
It is booting, has usb, battery, flashing needs special fastboot command for the boot partition
Port based on an unofficial LineageOS port
from https://www.los-legacy.de/17.1/zerofltexx, using kernel from https://github.com/Exynos7420/android_kernel_samsung_exynos7420/
What works:
- Kernel boots
- Display and touch input (tested with Weston)
- USB networking
Note: I removed camera support in kernel config for now, as there were related kernel crashes.
Wifi doesn't work either yet because the firmware dependencies/paths need to be fixed first.
The modprobe.conf is not necessary on those devices because they already
load the panel module using deviceinfo_modules_initfs. Let's skip the
modprobe.conf in that case so we don't need to add all panels in two places.
Simply disabling FIMC IS does not work however due to compilation
errors and a null pointer dereference. 01-fix-FIMC-IS-disabling.patch
takes care of this.
As with other exynos devices some additional things had to be disabled
to make the kernel compile after FIMC IS had been disabled,
specifically:
CONFIG_CAMERA_EEPROM
CONFIG_VIDEO_EXYNOS_MIPI_CSIS
CONFIG_LEDS_MAX77803
Apart from that we also have:
02-netfilter-symbols.patch, which fixes another compilation error.
03-usb_gadget-set-random-rndis-host-MAC-address-to-prev.patch (taken
from another device) which prevents host mac address being set to
00:00:00:00:00.
Kernel sources have been changed to the lineage-16.0 branch in the
exynos5420 repo, as that is where development happens at the moment.
based off from lineage os, manages to boot including ssh over usb.
had to disable:
CONFIG_HTC_RADIO_SMEM
CONFIG_HTC_MODEM_NOTIFIER
CONFIG_MSM_SMP2P
CONFIG_UIO_MSM_SHAREDMEM
[ci:skip-build]: already built successfully in CI
Instead of running the entire setup_usb_network_configfs function we
run the parts that are actually necessary for
setup_usb_network_android to succeed when it is run afterwards.
USB networking, Touchscreen and display are working.
CONFIG_SND_SOC_QDSP6V2 is omitted from kernel config for now as the resulting driver fails to build.
