Also update the patches with new, rebased ones straight from
the linux-amlogic mailing list, and rename them.
Signed-off-by: Ferass El Hafidi <vitali64pmemail@protonmail.com>
[ci:skip-build] already built successfully in CI
Plasma Bigscreen requires specific configuration on the RPi4 to tell it
to load some device-specific stuff. In this case to disable 4K mode as
the device can not handle it
[ci:skip-build] already built successfully in CI
Angler and Bullhead support is in early stage other msm899{2,4} does not
use the package yet => safe to use rc kernels to get closer to
qcom/for-next git tree.
Kernel 6.2 and 6.3 got few memory map fixes for angler and bullhead.
* Added 3 not yet merged patches for angler:
- add regulators
- memory overlap fixes
- proper cont_splash_mem setup
* Removed 0004-arm64-dts-qcom-msm8992-Don-t-use-sfpb-mutex.patch
(already applied and backported to 6.1 stable), thus renumber the
following patch.
* config
- Enable zram with lzo-rle, add pmb:kconfigcheck-zram (fixes warning:
zramctl: /dev/zram0: failed to set algorithm: Invalid argument)
- Enable crc32, lz4hc, zstd.
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
[ci:skip-build]: already built successfully in CI
Switch from armhf to armv7
- Apart of the usual stuff CONFIG_CRYPTO_AES_ARM_BS must be disabled
otherwise it breakes kernel compilation with some weird assembler error
Netboot
- CONFIG_BLK_DEV_NBD=y enables /dev/nbd support
- nbd.max_part=16 kernel parameter must be added otherwise it's zero
which causes that kpartx cannot create partitions
[ci:skip-build]: Already built successfully in CI
Also enable support for LIRC and /dev/uinput.
Signed-off-by: Ferass El Hafidi <vitali64pmemail@protonmail.com>
[ci:skip-build]: Already built successfully in CI
The modesetting driver previously provided by xf86-video-modesetting is
now shipped with xorg-server.
[ci:skip-build]: already built successfully in CI
From what I can tell, the package firmware-samsung-on7-wcnss-nv should
have been put as dependency since the on7lte package doesn't exist, and
I can't seem to find a trace of it.
[ci:skip-build] already successfully built in CI
Include adsp, cdsp and slpi firmware and add the linux-firmware-qca
dependency for qca6390-bt.
Also correct the module name for spi-geni-qcom in deviceinfo.
This is more of a version bump, compared to the past few releases. This
kernel should receive more of these types of releases, especially when
there is less hardware left to bring up.
[ci:skip-build] already built successfully in CI
Let the user select between two kernel variants using the different
device trees for the different panel variants (ea8061 and s6evr02)
[ci:skip-build]: Already built successfully in CI
This port has been compatible with GPU-accelerated UIs like Phosh and
Plasma Mobile for quite a while now. Enable these UIs in the
`pmbootstrap init` menu.
See #1939.
Store the full kernel config instead of a fragment, so
"pmbootstrap kconfig check" can properly verify that all required kernel
options are there. Without this, it would fail an upcoming check for
BINFMT_ELF and BINFMT_SCRIPT:
https://lists.sr.ht/~postmarketos/pmbootstrap-devel/patches/38508
With the full config, pmbootstrap found that ANDROID_PARANOID_NETWORK
was enabled while it should be disabled, so disable it.
Fix the mediatek drvgen related build failure with
00_disable_drvgen.patch from linux-wiko-ufeel and including cust.dtsi:
https://wiki.postmarketos.org/wiki/Porting_to_a_new_device#Removing_python2_dependency
[ci:skip-build]: already built successfully in CI
6.1 was not a valid kernel version causing the wlan module installed
into wrong location. 6.1.0 would be correct. Fix that
problem by upgrading to 6.1.12 and make the wlan installation
more robust.
[ci:skip-build]: already built successfully in CI
Add a generic device that should work on x86_64 ChromeOS devices. This
is mostly a copy of tablet-x64uefi, with ChromeOS-specific stuff from
google-kevin. Keeps the UEFI parts so that it can still be booted with
alternative firmware (i.e. MrChromebox's RW_LEGACY builds). Lightly
tested on a Lenovo IdeaPad 3 Chromebook 11IGL05 (codename "Lick").
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
linux-postmarketos-mediatek-mt6735 6.1.9 added full display support and hardware acceleration
as well as haptics. Add a phoc configuration file to set the display scale, and a feedbackd
theme to optimize vibration durations. Route console output to UART to leave the splash
screen clean and to help with debugging when necessary.
[ci:skip-build] already built successfully in CI
If the wlan0 interface is rfkilled down on boot, WiFi won't work until reboot.
It seems that quickly ifconfig'ing wlan0 up and down in sysinit is enough to work around the bug.
[ci:skip-build] already built successfully in CI
Since re-crypt was finished now all T20/T30 devices
can be switched to use generic u-boot approach
and mount eMMC as external storage to host PC.
Unfortunately or fortunately this deprecates
any Android use on device. Have fun!
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Changes to defconfig:
* Disable legacy usb gadgets (USB_ETH and friends)
* Enable Multi-Gen LRU (LRU_GEN)
[ci:skip-build]: already built successfully in CI
Bring up support for Samsung T110 Goyawifi.
Working: Display (framebuffer), touchscreen, buttons and Wi-Fi.
Include: kernel source and necesarry firmware for Wi-Fi and Bluetooth.
samsung-goyawifi: fix patch names
samsung-goyawifi: remove mesa-dri-gallium
samsung-goyawifi: fix keyboard in deviceinfo
samsung-goyawifi: fix lightdm
samsung-goyawifi: editor-config ci tabs
samsung-goyawifi: add linux kernel as depends
[ci:skip-build]: Already built successfully in CI
Add the firmware for the CyberTan WC121.
Configuration is added in the newest firmware-linux release, so
complete support will appear in the corresponding Alpine package soon.
[ci:skip-build]: already built successfully in CI
Make use of stock depthcharge bootloader to not deal with U-Boot issues:
- broken USB
- broken eMMC
- broken latest version of U-Boot
Use extlinux instead of Grub for users with U-Boot to simplify process.
Also, some of old U-Boot builds may not support EFI.
[ci:skip-build] already built successfully in CI
Make use of stock depthcharge bootloader to not deal with U-Boot issues:
- broken USB
- broken eMMC
- broken latest version of U-Boot
Use extlinux instead of Grub for users with U-Boot to simplify process.
Also, some of old U-Boot builds may not support EFI.
[ci:skip-build] already built successfully in CI
New features:
* msm8994-huawei-angler: Add sdhc1 definition (internal SD card).
Backporting 3 patches:
* 0001-arm64-dts-msm8992-bullhead-add-memory-hole-region.patch
fixes bullhead boot since 6.0-rc1, already in qcom tree
* 0002-arm64-dts-qcom-msm8992-bullhead-Fix-cont_splash_mem-.patch
memory fix, likely to be merged
* 0003-arm64-dts-qcom-msm8992-bullhead-Disable-dfps_data_me.patch
memory fix, likely to be merged
* 0004-arm64-dts-qcom-msm8992-Don-t-use-sfpb-mutex.patch
memory fix, likely to be merged
* 0005-arm64-dts-msm8994-angler-fix-the-memory-map.patch
fixes angler reset during starting services in rootfs,
likely to be merged
Remove all backported commits from newer versions.
While at it, remove various CONFIG_NET_VENDOR_.* and
CONFIG_MSM_.* and CONFIG_.*_QCOM_.* for other SOCs.
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
[ci:skip-build]: already built successfully in CI
Shared SoC package for MSM8909
Currently provides a dummy soc-qcom-msm8909 package that depends on
soc-qcom-msm8916 and a soc-qcom-msm8909-modem package for modem support.
Since the RTC like on most Qualcomm chips is read-only, use
swclock-offset package to fix up time after boot.
And since we don't need msm-fb-refresher on mainline, move it to the
downstream kernel subpackage.
Basic support for the Kobo Libra H2O ebook reader.
Waveform handling shares the same oddities as for the Kobo Clara HD, the
existing waveform from eMMC is used.
Preferred way to install is to export the eMMC as USB Mass storage,
backing it up, and installing there.
U-Boot is a more recent one than the factory u-boot, supporting easy
access for buttons/LEDs. Pressing PageUp while powering on gives you the
possibility to enable USB mass storage mode to restore your backup.
Kernel is the near mainline kernel also used by the Kobo Clara HD.
It lacks some devicetree additions which are planned for the next
update, but basic things like buttons, usb, serial and wifi are
supported.
The WCNSS firwmare used for motorola-harpia seems to have weird issues
that prevent using WiFi properly except for a few limited channels. It
is not clear why this happens, it seems to be some peculiar firmware
difference (perhaps the channels need to be enabled with some
non-standard command).
Since Motorola uses the same signing keys for all their MSM8916
devices, it is possible to use the firmware from other devices instead.
Initial testing shows promising results when using the older WCNSS
firmware from motorola-osprey instead, it does not seem to have this
issue.
It's not clear yet if this has any negative effects. The WCNSS firmware
should not be device-specific, but theoretically it could be (if
Motorola made some weird changes inside it).
For now just package it in firmware-motorola-osprey-wcnss. This package
can be easily installed on harpia devices for testing (using apk add)
and will then take precendence over the default firmware from the
firmware partition (via msm-firmware-loader).
Move firmware-motorola-osprey from testing to community so that the
package is preserved for motorola-harpia users (testing is deleted in
stable branches).
[ci:skip-build]: already built successfully in CI
motorola-osprey can generally use the firmware from motorola-harpia
(which is a bit newer). However, the WCNSS_qcom_wlan_nv.bin is usually
device specific (it contains some kind of calibration values for
WiFi/BT).
The file packaged in firmware-motorola-osprey-wcnss-nv is identical to
the file in firmware-motorola-harpia-wcnss-nv. However, It looks a bit
like this might be a mistake in the source repository
(https://github.com/pmsourcedump/firmware-motorola-osprey). The
wlan/prima folder there is completely identical to the one used for
motorola-harpia, but the stock ROM and LineageOS use different files.
Fix this by packaging the file from TheMuppets. Also modernize the
firmware-motorola-osprey package by applying pil-squasher to the
venus/video firmware.
motorola-osprey has a very clunky name at the moment "Motorola Moto G
3rd gen. (2015)". The device was mostly just called "Motorola Moto G"
by Motorola, so it is hard to choose a fitting (but unique) name.
In the postmarketOS wiki it is called "Motorola Moto G 2015" so let's
just drop the "3rd gen." in the pmOS device package as well.
Also make the deviceinfo consistent with harpia while at it.
This adds initial support to CutiePi tablet, with basic peripherals, sound, touchscreen, and wireless support.
Signed-off-by: Raffaele Tranquillini <raffaele.tranquillini@gmail.com>
Add peripheral overlays
Signed-off-by: Raffaele Tranquillini <raffaele.tranquillini@gmail.com>
[ci:skip-build]: Already built successfully in CI
Use msm8916 kernel package instead of linux-postmarketos-qcom-msm8939
Also remove rmi_core from deviceinfo_modules_initfs
since it's automatically pulled by rmi_i2c
This is a version bump for the sm6125 mainline kernel fork.
Changes:
* Added UFS nodes to the sm6125 platform
* Enabled UFS nodes for xiaomi-laurel
* Enabled configs required for UFS support (Notoriously
CONFIG_PHY_QCOM_QMP)
* Filled in EXTRAVERSION for kernel fork
* Added SMD RPM regulators for xiaomi-laurel
Signed-off-by: Lux Aliaga <they@mint.lgbt>
[ci:skip-build]: Already built successfully in CI
This is an early mainline port for the MediaTek MT6763 Helio P65/G70/G8*
SoCs that boots with all 8 cores online, logs on display (simplefb) or
UART serial console, USB gadget mode facilitating netbooting
postmarketOS while tethered via RNDIS and PMIC enabling functions like
vibrator, power/volume keys.
Since I'm not going by the "mint" alias anymore, I've decided to fix
that on the APKBUILDs
Signed-off-by: Lux Aliaga <they@mint.lgbt>
[ci:skip-build]: Already built successfully in CI
This is a version bump for the sm6125 mainline kernel fork. It should
also fix a config issue.
Changes:
* Made QUSB2 built-in instead of a module (Fixes USB connectivity
issues)
* Updates to xiaomi-laurel device tree to fit new schema
* Changed maintainer name
Signed-off-by: Lux Aliaga <they@mint.lgbt>
Add new patches:
- enable serial console
- save relocation address to find KASLR
- buttons as keyboard input driver to navigate bootmenu
- bootmenu loop entry selection
Enable vulkan on supported hardware configurations
out of the box.
Change-Id: I6c8e1713e7c834aae3a162b8a681f5abde02ed5e
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
The file brcmfmac43455-sdio.raspberrypi,4-model-b.bin is now provided by
linux-firmware-brcm package in Alpine. Remove to symlink to stop the
file conflict.
Now that touchscreen driver is supported in kernel, include the module
in initfs so it's available there.
[ci:skip-build]: Already built successfully in CI
Remove mainline postfix in initramfs module list,
because sagit has only 1 kernel for now.
Blacklisting ipa module fixes poweroff.
See 68cdc1ea2b commit for more info.
[ci:skip-build]: already built successfully in CI
This is an early mainline port for the MediaTek MT6763 Helio P23 SoC
that just about boots in about 3 minutes with one core online, logs on
display (simplefb) or UART serial console and USB gadget mode
facilitating netbooting postmarketOS while tethered via RNDIS.
This contains a fix for second panel variant for samsung-hlte.
No more manual changes, .config was regenerated using kconfig migrate.
[ci:skip-build]: already built successfully in CI
This is an incomplete port but it has greater functionality than the existing downstream based one, which has been moved to unmaintained.
[ci:skip-build]: Already built successfully in CI
