yt-dlp when resumed was observed having written the same filename twice
into the file list. Perhaps once by the first download and once by the
resumed one?
This causes changes to the original branch to get merged with a single
sync. Before, it took 2 syncs; the first happened to update the synced/
branch, and the second merged changes from the synced/ branch into the
ajusted branch.
Using mergeToAdjustedBranch when tomerge == origbranch is probably
overkill, but it does work fine.
Sponsored-By: the NIH-funded NICEMAN (ReproNim TR&D3) project
(And allow it to be used in the --template although that seems unlikely to
be very useful.)
My use case for this is that one of the podcast feeds I subscribe to is
sometimes leaking episodes of some other podcast. The other podcast is also
very close to spam, so this may be a form of intentional spamming. I have
not been able to catch the podcast feed containing those episodes, so I
don't know which one is at fault. So putting this in the metadata will let
me eventually catch it.
Bug fix: Re-running git-annex adjust or sync when in an adjusted branch
would overwrite the original branch, losing any commits that had been made
to it since the adjusted branch was created.
When git-annex adjust is run in this situation, it will display a warning
about the diverged branches.
When git-annex sync is run in this situation, mergeToAdjustedBranch
will merge the changes from the original branch to the adjusted branch.
So it does not need to display the divergence warning.
Note that for some reason, I'm needing to run sync twice for that to
happen. The first run does not do the merge and the second does. I'm unsure
why and so am not fully done with this bug.
Sponsored-By: the NIH-funded NICEMAN (ReproNim TR&D3) project
The paragraph just above already shows how to configure .gitattributes
and the necessary git config. So this is redundant. Also, it makes
.gitattributes match *, which is likely not a good idea because those
files are not likely to be all text files.
Running git config --list inside .git then fails, so better to only
do that when --git-dir was specified explicitly. Otherwise, when the
repository is not bare, run the command inside the working tree.
Also make init detect when the uuid it just set cannot be read and fail
with an error, in case git changes something that breaks this later.
I still don't actually understand why git-annex add/assist -J2 was
affected but -J1 was not. But I did show that it was skipping writing to
the location log, because the uuid was NoUUID.
Sponsored-by: Graham Spencer on Patreon
Command.Add.seek starts concurrency with CommandStages. And for
Command.Sync, it needs TransferStages. So, to get both types of concurrency
for the two different parts, it either needs to change the type of
concurrency in between, or just call startConcurrency once for each.
It seems safe enough to call startConcurrency twice, because it does shut
down concurrency (mostly) at the end, and eg the old Annex.workers get
emptied.
Sponsored-by: unqueued on Patreon
This ended up having an interface like sync, rather than like get/copy/drop.
That let it be implemented in terms of sync, which took a lot less code.
Also, it lets it handle many of the edge cases that sync does, such as
getting files that are not visible in a --hide-missing branch, and sending
files to exporttree remotes.
As well as being easier to implement, `git-annex satisfy myremote` makes
sense as it satisfies the preferred content settings of the remote.
`git-annex satisfy somefile` does not form a sentence that makes sense. So
while -C can be a little bit annoying, it still makes sense to have this
syntax.
Note that, while I initially thought this would also satisfy numcopies, it
does not. Arguably it ought to. But, sync does not send files in order to
satisfy numcopies, it only sends files to satisfy preferred content. And
it's important that this transfer the same files as sync does, because
it will probably be used in a workflow where the user sometimes syncs and
sometimes satisfies, and does not expect satisfy to do things that sync
would not do.
(Also opened a new bug that also affects sync et all, not only this command.)
Sponsored-by: Nicholas Golder-Manning on Patreon
This was already possible, but it was rather hard to come up with the
complex shell command needed.
Note that the diff output starts with "diff a/... b/...".
I left off the "--git" because it's not a git format diff.
