Propagate Annex.force into the remote's Annex state.
Fixes this problem:
joey@darkstar:~/tmp/xxxx>git-annex copy mmm --to origin --force
copy mmm (to origin...)
not enough free space, need 908.72 MB more (use --force to override this check or adjust annex.diskreserve)
failed to send content to remote
failed
Does beg the question if anything else should be propagated.
Some things like Annex.forcenumcopies certianly not; using --numcopies
overrides the number of copies the current repo wants, not all of them.
Sponsored-by: Graham Spencer on Patreon
There's still a 60 second delay in this situation because it retries,
in case the failure was due to something recoverable like another
process.
Sponsored-by: unqueued on Patreon
New command, currently limited to changing autoenable= setting of a special remote.
It will probably never be used for more than that given the limitations on
it.
Sponsored-by: Brock Spratlen on Patreon
enableremote: Support enableremote of a git remote (that was previously set
up with initremote) when additional parameters such as autoenable= are
passed.
The enableremote special case for regular git repos is intended to handle
ones that don't have a UUID probed, and the user wants git-annex to
re-probe. So, that special case is still needed. But, in that special
case, the user is not passing any extra parameters. So, when there are
parameters, instead run the special remote setup code. That requires there
to be a uuid known already, and it allows changing things like autoenable=
Remote.Git.enableRemote changed to be a no-op if a git remote with the name
already exists. Which it generally will in this case.
Sponsored-by: Jack Hill on Patreon
Don't need to be sanitized and displaying them messes up actually
exiting with the right exit code! And broke the test suite.
Sponsored-by: Brett Eisenberg on Patreon
These are quite low-level, but still there is no point in displaying
escape sequences that have been embedded in a key to the terminal.
I think these are the only remaining commands that didn't use safe
output, except for cases where git-annex is speaking a protocol to
itself.
Sponsored-by: Kevin Mueller on Patreon
When displaying a ByteString like "💕", safeOutput operates on
individual bytes like "\240\159\146\149" and isControl '\146' = True,
so it got truncated to just "\240".
So, only treat the low control characters, and DEL, as control
characters.
Also split Utility.Terminal out of Utility.SafeOutput. The latter needs
win32, but Utility.SafeOutput is used by Control.Exception, which is
used by Setup.
Sponsored-by: Nicholas Golder-Manning on Patreon
I'm on the fence about this. Notice that pulling from a git remote can
pull branches that have escape sequences in their names. Git will
display those as-is. Arguably git should try harder to avoid that.
But, names of remotes are usually up to the local user, and autoenable
changes that, and so it makes sense that git chooses to display control
characters in names of remotes, and so autoenable needs to guard against
it.
Sponsored-by: Graham Spencer on Patreon
Seems unlikely to have a tab in a path, but it's not a control character
that needs to be prevented either.
Left \n \r \v and \a as other non-threatening control characters
that are still obnoxious to have in a filepath because of how it causes
issues with display and/or with shell scripting.
This causes an encodeBS thunk, and the first evaluation of the string
forces it. From then on, further uses operate on a ByteString. This
avoids converting repeatedly.
Searched for uses of putStr and hPutStr and changed appropriate ones to filter
out control characters and quote filenames.
This notably does not make find and findkeys quote filenames in their default
output. Because they should only do that when stdout is non a pipe.
A few commands like calckey and lookupkey seem too low-level to make sense to filter
output, so skipped those.
Also when relaying output from other commands that is not progress output,
have git-annex filter out control characters.
Sponsored-by: k0ld on Patreon
