If a transfer fails for some reason, but some data managed to be sent, the
transfer will be retried. (The assistant already did this.)
Possible impacts:
* More ssh prompts if ssh needs to prompt for a password to connect to a
host, or is prompting about some other problem like a ssh key mismatch.
* More data transfer due to retrying, epecially when a remote does not
support resuming a transfer.
In the worst case, a lot of data will be transferred but it fails before
the end, and then all that data gets transferred again plus one byte more;
repeat until it manages to get the whole file.
Note that I had one in Annex.Action.startup too, but it resulted in a weird
message printed by ssh, "channel 2: bad ext data". I don't know why, but
it only happened when transferinfo was run, so I wonder
if 983a95f021 introduced a fragility somehow.
This is a work in progress. It compiles and is able to do basic command
dispatch, including git autocorrection, while using optparse-applicative
for the core commandline parsing.
* Many commands are temporarily disabled before conversion.
* Options are not wired in yet.
* cmdnorepo actions don't work yet.
Also, removed the [Command] list, which was only used in one place.
Only the assistant uses these, and only the assistant cleans them up, so
make only git annex transferkeys write them,
There is one behavior change from this. If glacier is being used, and a
manual git annex get --from glacier fails because the file isn't available
yet, the assistant will no longer later see that failed transfer file and
retry the get. Hope no-one depended on that old behavior.
Motivation: Hook scripts for nautilus or other file managers
need to provide the user with feedback that a file is being downloaded.
This commit was sponsored by THM Schoemaker.
I've been disliking how the command seek actions were written for some
time, with their inversion of control and ugly workarounds.
The last straw to fix it was sync --content, which didn't fit the
Annex [CommandStart] interface well at all. I have not yet made it take
advantage of the changed interface though.
The crucial change, and probably why I didn't do it this way from the
beginning, is to make each CommandStart action be run with exceptions
caught, and if it fails, increment a failure counter in annex state.
So I finally remove the very first code I wrote for git-annex, which
was before I had exception handling in the Annex monad, and so ran outside
that monad, passing state explicitly as it ran each CommandStart action.
This was a real slog from 1 to 5 am.
Test suite passes.
Memory usage is lower than before, sometimes by a couple of megabytes, and
remains constant, even when running in a large repo, and even when
repeatedly failing and incrementing the error counter. So no accidental
laziness space leaks.
Wall clock speed is identical, even in large repos.
This commit was sponsored by an anonymous bitcoiner.
There was confusion in different parts of the progress bar code about
whether an update contained the total number of bytes transferred, or the
number of bytes transferred since the last update. One way this bug
showed up was progress bars that seemed to stick at zero for a long time.
In order to fix it comprehensively, I add a new BytesProcessed data type,
that is explicitly a total quantity of bytes, not a delta.
Note that this doesn't necessarily fix every problem with progress bars.
Particularly, buffering can now cause progress bars to seem to run ahead
of transfers, reaching 100% when data is still being uploaded.
However, I don't yet have a reliable way to deal with files being modified
while they're being transferred. I have code that detects it on the sending
side, but the receiver is still free to move the wrong content into its
annex, and record that it has the content. So that's not acceptable, and
I'll need to work on it some more.
However, at this point I can use a direct mode repository as a remote and
transfer files from and to it.
Files are now written to a tmp directory in the remote, and once all
chunks are written, etc, it's moved into the final place atomically.
For now, checkpresent still checks every single chunk of a file, because
the old method could leave partially transferred files with some chunks
present and others not.
When a transfer fails, the progress info can be used to intelligently
retry it. If the transfer managed to make some progress, but did not
fully complete, then there's a good chance that a retry will finish it
(or at least make more progress).
Transfer info files are updated when the callback is called, updating
the number of bytes transferred.
Left unused p variables at every place the callback should be used.
Which is rather a lot..
Not yet tested and places git-annex-shell is run need to be modified to
pass the new field settings.
Note that rsyncServerSend was changed to fork, rather than directly exec
rsync, because it needs to keep the transfer lock held, and clean up the
transfer log when done.
Supporting multiple directory hash types will allow converting to a
different one, without a flag day.
gitAnnexLocation now checks which of the possible locations have a file.
This means more statting of files. Several places currently use
gitAnnexLocation and immediately check if the returned file exists;
those need to be optimised.
Many functions took the repo as their first parameter. Changing it
consistently to be the last parameter allows doing some useful things with
currying, that reduce boilerplate.
In particular, g <- gitRepo is almost never needed now, instead
use inRepo to run an IO action in the repo, and fromRepo to get
a value from the repo.
This also provides more opportunities to use monadic and applicative
combinators.
This new approach allows filtering out checks from the default set that are
not appropriate for a command, rather than having to list every check
that is appropriate. It also reduces some boilerplate.
Haskell does not define Eq for functions, so I had to go a long way around
with each check having a unique id. Meh.
These were a mistake, they make the type signatures harder to read and
less flexible. The CommandSeek, CommandStart, CommandPerform, and
CommandCleanup types were a good idea, but composing them with the
parameters expected is going too far.
It compiles. It sorta works. Several subcommands are FIXME marked and
broken, because things that used to accept separate --backend and --key
params need to be changed to accept just a --key that encodes all the key
info, now that there is metadata in keys.
Rename Locations functions for better consitency, and make their values
more consistent too.
Used </> rather than manually building paths. There are still more places
that manually do so, but are tricky, due to the behavior of </> when
the second FilePath is absolute. So I only changed places where
it obviously was relative.
