The flush was only done Annex.run' to make sure that the queue was flushed
before git-annex exits. But, doing it there means that as soon as one
change gets queued, it gets flushed soon after, which contributes to
excessive writes to the database, slowing git-annex down.
(This does not yet speed git-annex up, but it is a stepping stone to
doing so.)
Database queues do not autoflush when garbage collected, so have to
be flushed explicitly. I don't think it's possible to make them
autoflush (except perhaps if git-annex sqitched to using ResourceT..).
The comment in Database.Keys.closeDb used to be accurate, since the
automatic flushing did mean that all writes reached the database even
when closeDb was not called. But now, closeDb or flushDb needs to be
called before stopping using an Annex state. So, removed that comment.
In Remote.Git, change to using quiesce everywhere that it used to use
stopCoProcesses. This means that uses on onLocal in there are just as
slow as before. I considered only calling closeDb on the local git remotes
when git-annex exits. But, the reason that Remote.Git calls stopCoProcesses
in each onLocal is so as not to leave git processes running that have files
open on the remote repo, when it's on removable media. So, it seemed to make
sense to also closeDb after each one, since sqlite may also keep files
open. Although that has not seemed to cause problems with removable
media so far. It was also just easier to quiesce in each onLocal than
once at the end. This does likely leave performance on the floor, so
could be revisited.
In Annex.Content.saveState, there was no reason to close the db,
flushing it is enough.
The rest of the changes are from auditing for Annex.new, and making
sure that quiesce is called, after any action that might possibly need
it.
After that audit, I'm pretty sure that the change to Annex.run' is
safe. The only concern might be that this does let more changes get
queued for write to the db, and if git-annex is interrupted, those will be
lost. But interrupting git-annex can obviously already prevent it from
writing the most recent change to the db, so it must recover from such
lost data... right?
Sponsored-by: Dartmouth College's Datalad project
When importing from versioned remotes, fix tracking of the content of
deleted files.
Only S3 supports versioning so far, so only it was affected.
But, the draft import/export interface for external remotes also seemed to
need a change, so that versionedExport could be set.
S3: Speed up importing from a large bucket when fileprefix= is set by only
asking for files under the prefix.
getBucket still returns the files with the prefix included, so the rest of
the fileprefix stripping still works unchanged.
Sponsored-by: Dartmouth College's DANDI project
move: Fix openFile crash with -J
This does make them a bit slower, although usually the log file is not
very big, so even when it's being rewritten, they will not block for
long taking the lock. Still, little slowdowns may add up when moving a lot
file files.
A less expensive fix would be to use something lower level than openFile
that does not check if the file is already open for write by another
thread. But GHC does not seem to provide anything convenient; even mkFD
checks for a writing thread.
fullLines is no longer necessary since these functions no longer will
read the file while it's being written.
Sponsored-by: Dartmouth College's DANDI project
* trust, untrust, semitrust, dead: Fix behavior when provided with
multiple repositories to operate on.
* trust, untrust, semitrust, dead: When provided with no parameters,
do not operate on a repository that has an empty name.
The man page and usage already indicated that multiple repos could be
provided to these commands, but they actually used unwords to combine
everything into string, and found a repo matching that string. This was
especially bad when no parameters resulted in the empty string and some
repo happened to have an empty description.
This does change the behavior, and it's possible someone relied on the
current behavior to eg, trust a repo by name with the name not quoted into
a single parameter. But fixing the empty string bug and matching the
documentation are worth breaking that usage.
Note that git-annex init/reinit do still unwords multiple parameters when
provided to them. That is inconsistent behavior, but it certianly seems
possible that something does run git-annex init with an unquoted
description, and I don't think it's worth breaking that just to make it more
consistent with these other commands.
Sponsored-by: Boyd Stephen Smith Jr. on Patreon
This is to improve this case:
joey@darkstar:~/tmp/yyyy>git-annex trust
git-annex: no remote specified
The command does not need to be run with a remote, any repository name
will do, including eg "here".
Sponsored-by: Brock Spratlen on Patreon
Avoids displaying warning about git-annex restage needing to be run in
situations where it does not.
Closing a handle flushes it anyway, so no need for an explict flush. The
handle does get closed twice, but that's fine, the second one does nothing.
Sponsored-by: Dartmouth College's DANDI project
