Can't trust the key size to be accurate for tmp and bad keys, so check
actual file size. In the wild I saw the old code be wrong by a factor
of about 100!
If all tmp/bad keys are empty, they're not shown in status at all.
Showing 0 bytes and suggesting to clean it up seemed weird..
Stale and bad files are rare, so it's more efficient to use inAnnex to see
if they can be deleted, rather than keeping the list of all present keys
around for them.
Before, it leaked space due to caching lists of keys. Now all necessary
data about keys is calculated as they stream in.
The "nearly constant" is due to getKeysPresent, which builds up a lot
of [] thunks as it traverses .git/annex/objects/. Will deal with it later.
Much of the memory bloat turned out to be due to getKeysReferenced
containing a mapM, which is strict and buffered the whole list
rather than streaming it.
The other half of the bloat was due to building a temporary Set
in order to call S.difference. While that is more cpu efficient,
I switched to successive S.delete, since with it, I can run a whole
git annex unused in less than 8 mb of memory.
The whole Set of keys with content available is still stored in memory,
so running unused in a repo with a whole lot of file content will still
use more memory. In a repo containing 6000 files, it needed 40 mb.
Note that the status command still uses the bloatful getKeysReferenced.
This has two benefits.
1. When a lot of refs are going to be received, get them via lower cost
connection when possible.
2. Allows ctrl-c of sync after the cheaper remotes have been pulled from
(or pushed to).
Rather than go through the location log to see which files are present on
the remote, it simply looks at the disk contents directly.
I benchmarked this speeding up scanning 834 files, from an annex on my
phone's SSD, from 11.39 seconds to 1.31 seconds. (No files actually moved.)
Also benchmarked 8139 files, from an annex on spinning storage,
speeding up from 103.17 to 13.39 seconds.
Note that benchmarking with an encrypted annex on flash actually showed a
minor slowdown with this optimisation -- from 13.93 to 14.50 seconds. Seems
the overhead of doing the crypto needed to get the filenames to directly
check can be higher than the overhead of looking up data in the location
log. (Which says good things about how well the location log and git have
been optimised!) It *may* make sense to make encrypted local remotes not
have hasKeyCheap set; further benchmarking is called for.
Eventually, git-annex might try running this after making changes to
a remote. I have not yet thought of a good way for it to tell which
remotes it needs to run it on though. It can't just do it when
shutting down a cached ssh connection, because ssh connection caching
is optional, and that would not handle local remotes not accessed over ssh
either.
Now changes are staged into the branch's index, but not committed,
which avoids growing a large journal. And sync and merge always
explicitly commit, ensuring that even when they do nothing else,
they commit the staged changes.
Added a flag file to indicate that the branch's journal contains
uncommitted changes. (Could use git ls-files, but don't want to run
that every time.)
In the future, this ability to have uncommitted changes staged in the
journal might be used on remotes after a series of oneshot commands.
Now gitattributes are looked up, efficiently, in only the places that
really need them, using the same approach used for cat-file.
The old CheckAttr code seemed very fragile, in the way it streamed files
through git check-attr.
I actually found that cad8824852
was still deadlocking with ghc 7.4, at the end of adding a lot of files.
This should fix that problem, and avoid future ones.
The best part is that this removes withAttrFilesInGit and withNumCopies,
which were complicated Seek methods, as well as simplfying the types
for several other Seek methods that had a Backend tupled in.
Can be used to specify what file the url is added to. This can be used to
override the default filename that is used when adding an url, which is
based on the url. Or, when the file already exists, the url is recorded as
another location of the file.
Under ghc 7.4, this seems to be able to handle all filename encodings
again. Including filename encodings that do not match the LANG setting.
I think this will not work with earlier versions of ghc, it uses some ghc
internals.
Turns out that ghc 7.4 has a special filesystem encoding that it uses when
reading/writing filenames (as FilePaths). This encoding is documented
to allow "arbitrary undecodable bytes to be round-tripped through it".
So, to get FilePaths from eg, git ls-files, set the Handle that is reading
from git to use this encoding. Then things basically just work.
However, I have not found a way to make Text read using this encoding.
Text really does assume unicode. So I had to switch back to using String
when reading/writing data to git. Which is a pity, because it's some
percent slower, but at least it works.
Note that stdout and stderr also have to be set to this encoding, or
printing out filenames that contain undecodable bytes causes a crash.
IMHO this is a misfeature in ghc, that the user can pass you a filename,
which you can readFile, etc, but that default, putStr of filename may
cause a crash!
Git.CheckAttr gave me special trouble, because the filenames I got back
from git, after feeding them in, had further encoding breakage.
Rather than try to deal with that, I just zip up the input filenames
with the attributes. Which must be returned in the same order queried
for this to work.
Also of note is an apparent GHC bug I worked around in Git.CheckAttr. It
used to forkProcess and feed git from the child process. Unfortunatly,
after this forkProcess, accessing the `files` variable from the parent
returns []. Not the value that was passed into the function. This screams
of a bad bug, that's clobbering a variable, but for now I just avoid
forkProcess there to work around it. That forkProcess was itself only added
because of a ghc bug, #624389. I've confirmed that the test case for that
bug doesn't reproduce it with ghc 7.4. So that's ok, except for the new ghc
bug I have not isolated and reported. Why does this simple bit of code
magnet the ghc bugs? :)
Also, the symlink touching code is currently broken, when used on utf-8
filenames in a non-utf-8 locale, or probably on any filename containing
undecodable bytes, and I temporarily commented it out.
I had not realized what a memory leak the lazy state monad could be,
although I have not seen much evidence of actual leaking in git-annex.
However, if running git-annex on a great many files, this could matter.
The additional Utility.State.changeState adds even more strictness,
avoiding a problem I saw in github-backup where repeatedly modifying
state built up a huge pile of thunks.
Done by adding a oneshot mode, in which location log changes are written to
the journal, but not committed. Taking advantage of git-annex's existing
ability to recover in this situation.
This is used by git-annex-shell and other places where changes are made to
a remote's location log.
Fscking a remote is now supported. It's done by retrieving
the contents of the specified files from the remote, and checking them,
so can be an expensive operation.
(Several optimisations are possible, to speed it up, of course.. This is
the slow and stupid remote fsck to start with.)
Still, if the remote is a special remote, or a git repository that you
cannot run fsck in locally, it's nice to have the ability to fsck it.
If you have any directory special remotes, now would be a good time to
fsck them, in case you were hit by the data loss bug fixed in the
previous release!
