git upload-pack makes some uncessary writes in sequence, this tries to
gather them together to avoid needing to send multiple DATA packets when
just one will do.
In a small pull, this reduces the average number of DATA packets from
4.5 to 2.5.
Still a couple bugs:
* Closing the connection to the server leaves git upload-pack /
receive-pack running, which could be used to DOS.
* Sometimes the data is transferred, but it fails at the end, sometimes
with:
git-remote-tor-annex: <socket: 10>: commitBuffer: resource vanished (Broken pipe)
Must be a race condition around shutdown.
Almost working, but there's a bug in the relaying.
Also, made tor hidden service setup pick a random port, to make it harder
to port scan.
This commit was sponsored by Boyd Stephen Smith Jr. on Patreon.
This is most of the way to having the p2p protocol working over tor
hidden services, at least enough to do git push/pull.
The free monad was split into two, one for network operations and the
other for local (Annex) operations. This will allow git-remote-tor-annex
to run only an IO action, not needing the Annex monad.
This commit was sponsored by Remy van Elst on Patreon.
A bit tricky since Proto doesn't support threads. Rather than adding
threading support to it, ended up using a callback that waits for both
data on a Handle, and incoming messages at the same time.
This commit was sponsored by Denis Dzyubenko on Patreon.
Is content locking needed in the P2P protocol? Based on re-reading
bugs/concurrent_drop--from_presence_checking_failures.mdwn,
I think so: Peers can form cycles, and multiple peers can all be trying
to drop the same content.
So, added content locking to the protocol, with some difficulty.
The implementation is fine as far as it goes, but note the warning
comment for lockContentWhile -- if the connection to the peer is dropped
unexpectedly, the peer will then unlock the content, and yet the local
side will still think it's locked.
To be honest I'm not sure if Remote.Git's lockKey for ssh remotes
doesn't have the same problem. It checks that the
"ssh remote git-annex-shell lockcontent"
process has not exited, but if the connection closes afer that check,
the lockcontent command will unlock it, and yet the local side will
still think it's locked.
Probably this needs to be fixed by eg, making lockcontent catch any
execptions due to the connection closing, and in that case, wait a
significantly long time before dropping the lock.
This commit was sponsored by Anthony DeRobertis on Patreon.
For use with tor hidden services, and perhaps other transports later.
Based on Utility.SimpleProtocol, it's a line-based protocol,
interspersed with transfers of bytestrings of a specified size.
Implementation of the local and remote sides of the protocol is done
using a free monad. This lets monadic code be included here, without
tying it to any particular way to get bytes peer-to-peer.
This adds a dependency on the haskell package "free", although that
was probably pulled in transitively from other dependencies already.
This commit was sponsored by Jeff Goeke-Smith on Patreon.
ghc 8 added backtraces on uncaught errors. This is great, but git-annex was
using error in many places for a error message targeted at the user, in
some known problem case. A backtrace only confuses such a message, so omit it.
Notably, commands like git annex drop that failed due to eg, numcopies,
used to use error, so had a backtrace.
This commit was sponsored by Ethan Aubin.
* S3: Support the special case endpoint needed for the cn-north-1 region.
* Webapp: Don't list the Frankfurt region, as this (and some other new
regions) need V4 authorization which the aws library does not yet use.
This commit was sponsored by Nick Daly on Patreon.
If a transfer fails for some reason, but some data managed to be sent, the
transfer will be retried. (The assistant already did this.)
Possible impacts:
* More ssh prompts if ssh needs to prompt for a password to connect to a
host, or is prompting about some other problem like a ssh key mismatch.
* More data transfer due to retrying, epecially when a remote does not
support resuming a transfer.
In the worst case, a lot of data will be transferred but it fails before
the end, and then all that data gets transferred again plus one byte more;
repeat until it manages to get the whole file.
Multiple external special remote processes for the same remote will be
started as needed when using -J.
This should not beak any existing external special remotes, because running
multiple git-annex commands at the same time could already start multiple
processes for the same external special remotes.
Note that get --from foo --failed will get things that a previous get --from bar
tried and failed to get, etc. I considered making --failed only retry
transfers from the same remote, but it was easier, and seems more useful,
to not have the same remote requirement.
Noisy due to some refactoring into Types/
Ignore exceptions when getting the cost and availability for the remote,
and return sane defaults. These defaults are not cached, so if a special
remote program has a transient problem, it will re-query it later.
Removed the instance LensGpgEncParams RemoteConfig because it encouraged
code that does not take the RemoteGitConfig into account.
RemoteType's setup was changed to take a RemoteGitConfig,
although the only place that is able to provide a non-empty one is
enableremote, when it's changing an existing remote. This led to several
folow-on changes, and got RemoteGitConfig plumbed through.
This is useful for makking a special remote that anyone with a clone of the
repo and your public keys can upload files to, but only you can decrypt the
files stored in it.
The naming is unofrtunately not consistent, but the gnupg-options
were only used for encrypting, and it's too late to change that.
It would be nice to have a third setting that is always passed to gnupg,
but ~/.gnupg/options can be used to specify such global options when really
needed.
Since git-annex unsets these when started, they have to be explicitly
propigated. Also, this makes --git-dir and --work-tree settings be
reflected in the environment.
The need for this came up in
https://github.com/DanielDent/git-annex-remote-rclone/issues/3
