9cb250f7be got the ones in RawFilePath,
but there were others that used the one from unix-compat, which fails at
runtime on windows. To avoid this,
import System.PosixCompat.Files hiding removeLink
This commit was sponsored by Ethan Aubin.
I'm not sure if git documents it aside from 0 and 1, but any integer
can be interpreted as a bool by it. Doing the same in git-annex is good
for consistency. Also, I am planning a config that starts out as a
numeric range, but will later transition to a simple bool (hopefully),
which this interpretation supports well.
All properties changed to use them, except for
prop_encode_c_decode_c_roundtrip, which already filtered to ascii
for other reasons.
A few modules had to be split out, because Setup does not build-depend
on QuickCheck.
nukeFile replaced with removeWhenExistsWith removeLink, which allows
using RawFilePath. Utility.Directory cannot use RawFilePath since setup
does not depend on posix.
This commit was sponsored by Graham Spencer on Patreon.
Notable wins in Annex.Locations which was sometimes doing 6 conversions
in a single function call.
This commit was sponsored by Denis Dzyubenko on Patreon.
This reverts commit c142696c58.
It turns out it was not needed; 681313dfd4
fixed up the git dir, so setting cwd to it works ok.
But worst, this commit broke the test suite massively. I don't understand how.
git-annex get was failing. Very weirdly, git-annex find in a fresh
clone of an annex repo, during autoinit, was displaying a side message
-- but side messages are disabled when running find.
This fixes the bug.
Note, it's only done when GIT_DIR is set. When it's not set,
Git.Construct already handled it. This is why it was only noticed with this
git submodule command.
This commit was sponsored by Brett Eisenberg on Patreon.
If .git is a gitlink file, setting cwd to it will fail, but --git-dir
will succeed. And this is the only place where it sets cwd when running
git, everywhere else already uses --git-dir.
Note that, git-annex's submodule fixup code usually converts gitlink
files to symlinks, so this wasn't usually problem. Still, worth fixing.
This commit was sponsored by Svenne Krap on Patreon.
This was the last one marked as a zombie. There might be others I don't
know about, but except for in the hypothetical case of a thread dying
due to an async exception before it can wait on a process it started, I
don't know of any.
It would probably be safe to remove the reapZombies now, but let's wait
and so that in its own commit in case it turns out to cause problems.
This commit was sponsored by Boyd Stephen Smith Jr. on Patreon.
Eliminate a zombie that was only cleaned up by the later zombie cleanup
code.
This is still not ideal, it would be cleaner if it used conduit or
something, and if the thread gets killed before waiting, it won't stop
the process.
Only remaining zombies are in CmdLine.Seek
This is only needed for the i386ancient build, so build in the git
version git-annex is built with, assuming git won't be upgraded, or if
it is, they just won't get the speedup of --buffer
This was a bit disappointing, I was hoping for a 2x speedup. But, I think
the metadata lookup is wasting a lot of time and also needs to be made to
stream.
The changes to catObjectStreamLsTree were benchmarked to not also speed
up --all around 3% more. Seems I managed to make it polymorphic after all.
The catObjectStream' is generic enough to let it be nicely used from
inside Annex monad.
Chan will be faster than DList here. Bearing in mind, it is unbounded,
but in reality will be bounded by the size of the stdio buffer through
git cat-file.
This speeds up --all by about 10% although I think only getting back to
the previous performance before I introduced that DList.
planned to use for an optimisation
most things using stagedDetails were not expecting to get dup files in a
conflicted merge and deal with them, so converted them to use
inRepoDetails.
And convert parser to attoparsec, probably faster.
Before, a parse failure threw the whole --stage output line in to the
filename, which was certianly a bad idea, so fixed that.
Turns out the %(rest) trick was not needed. Instead, just maintain a
list of files we've asked for, and each cat-file response is for the
next file in the list.
This actually benchmarks 25% faster than before! Very surprising, but it
must be due to needing to shove less data through the pipe, and parse
less.
This assumes that no location log files will have a newline or carriage
return in their name. catObjectStream skips any such files due to
cat-file not supporting them.
Keys have been prevented from containing newlines since 2011,
commit 480495beb4. If some old repo
had a key with a newline in it, --all will just skip processing that key.
Other things, like .git/annex/unused files certianly assume no newlines in
keys too, and AFAICR, such keys never actually worked.
Carriage return is escaped by preSanitizeKeyName since 2013. WORM keys
generated before that point could perhaps contain a CR. (URL probably not,
http probably doesn't support an URL with a raw CR in it.) So, added
a warning in fsck about such keys. Although, fsck --all will naturally
skip them, so won't be able to warn about them. Not entirely
satisfactory, but I'll bet there are not really any such keys in
existence.
Thanks to Lukey for finding this optimisation.
Fixes reversion in recent conversions, the old code relied on the GC
apparently, but the new code explicitly waits on the process, so must
close stdin handle first or the command will never exit.
Except for the assistant, which I think may use them between threads?
Most of the uses of SomeException were already catching only async exceptions.
But I did find a few places that were accidentially catching them.
This handles all createProcessSuccess callers, and aside from process
pools, the complete conversion of all process running to async exception
safety should be complete now.
Also, was able to remove from Utility.Process the old API that I now
know was not a good idea. And proof it was bad: The code size went *down*,
despite there being a fair bit of boilerplate for some future API to
reduce.
This handles all sites where checkSuccessProcess/ignoreFailureProcess
is used, except for one: Git.Command.pipeReadLazy
That one will be significantly more work to convert to bracketing.
(Also skipped Command.Assistant.autoStart, but it does not need to
shut down the processes it started on exception because they are
git-annex assistant daemons..)
forceSuccessProcess is done, except for createProcessSuccess.
All call sites of createProcessSuccess will need to be converted
to bracketing.
(process pools still todo also)
