init: Fix a reversion in the last release that prevented automatically
generating and setting a description for the repository.
Seemed best to factor out uuidDescMapRaw that does not
have the default mempty descrition behavior.
I don't much like that behavior, but I know things depend on it.
One thing in particular is `git annex info` which lists the uuids and
descriptions; if the current repo has been initialized in some way that
means it does not have a description, it would not show up w/o that.
(Not only repos created due to this bug might lack that. For example a repo
that was marked dead and had --drop-dead delete its git-annex branch info,
and then came back from the dead would similarly not be in the uuid.log.
Also there have been other versions of git-annex that didn't set a default
description; for years there was no default description.)
When downloading an url and the destination file exists but is empty,
avoid using http range to resume, since a range "bytes=0-" is an unusual
edge case that it's best to avoid relying on working.
This is known to fix a case where importfeed downloaded a partial feed from
such a server. Since importfeed uses withTmpFile, the destination always exists
empty, so it would particularly tickle such problem servers. Resuming from 0
is otherwise possible, but unlikely.
get, move, copy, sync: When -J or annex.jobs has enabled concurrency,
checksum verification uses a separate job pool than is used for
downloads, to keep bandwidth saturated.
Not yet done for upload checksum verification, but that only affects
remotes on local disks.
Avoid a delay at startup when concurrency is enabled and there are
rsync or gcrypt special remotes, which was caused by git-annex
opening a ssh connection to the remote too early.
sshOptions makes a connection to the ssh server if one is not already open,
when concurrency is enabled. Avoid doing that at startup, when the remote
list is being built, but the remote may not be used at all.
Instead, rsync/gcrypt now runs sshOptions once per ssh connection to the
server. This should not be significant overhead since Remote.Git already
has the same overhead (as do Bup and Ddar).
The hoped for optimisation of CommandStart with -J did not materialize.
In fact, not runnign CommandStart in parallel is slower than -J3.
So, CommandStart are still run in parallel.
(The actual bad performance I've been seeing with -J in my big repo
has to do with building the remoteList.)
But, this is still progress toward making -J faster, because it gets rid
of the onlyActionOn roadblock in the way of making CommandCleanup jobs
run separate from CommandPerform jobs.
Added OnlyActionOn constructor for ActionItem which fixes the
onlyActionOn breakage in the last commit.
Made CustomOutput include an ActionItem, so even things using it can
specify OnlyActionOn.
In Command.Move and Command.Sync, there were CommandStarts that used
includeCommandAction, so output messages, which is no longer allowed.
Fixed by using startingCustomOutput, but that's still not quite right,
since it prevents message display for the includeCommandAction run
inside it too.
When running multiple concurrent actions, the cleanup phase is run in a
separate queue than the main action queue. This can make some commands
faster, because less time is spent on bookkeeping in between each file
transfer.
But as far as I can see, nothing will be sped up much by this yet, because
all the existing cleanup actions are very light-weight. This is just groundwork
for deferring checksum verification to cleanup time.
This change does mean that if the user expects -J2 will mean that they see no
more than 2 jobs running at a time, they may be surprised to see 4 in some
cases (if the cleanup actions are slow enough to notice).
It might also make sense to enable background cleanup without the -J,
for at least one cleanup action. Indeed, that's the behavior that -J1
has now. At some point in the future, it make make sense to make the
behavior with no -J the same as -J1. The only reason it's not currently
is that git-annex can build w/o concurrent-output, and also any bugs
in concurrent-output (such as perhaps misbehaving on non-VT100 compatible
terminals) are avoided by default by only using it when -J is used.
Add back support for ftp urls, which was disabled as part of the fix for
security hole CVE-2018-10857 (except for configurations which enabled curl
and bypassed public IP address restrictions). Now it will work if allowed
by annex.security.allowed-ip-addresses.
Renamed annex.security.allowed-http-addresses to
annex.security.allowed-ip-addresses because it is not really specific to
the http protocol, also limiting eg, git-annex's use of ftp and via
youtube-dl, several other protocols.
The old name for the config will still work.
If both old and new name are set, the new name will win.
When a remote is configured to be readonly, don't allow changing what's
exported to it.
This was missed in the original export remote implementation, but it makes
sense for a readonly export remote to not be allowed to change.
~/.profile works for bash, but not all other login shells.
This setting PATH is a minor convenience for users, particuarly since
typing on android is so much harder. The usual linux standalone bundle
just expects the user to know how to add it to PATH. I don't want this
code to grow special cases for every possible login shell. So displaying a
message to the presumably minority who don't use bash seems like the best
choice.
Longer term, I'd hope termux gets some way to set an environment variable
for all login shells. Systems using PAM can, via ~/.pam_environment. Or
alternatively, add a git-annex package to termux, even if just an installer
package. I'd rather spend time on either of those than on making this minor
thing support more login shells.
This commit was sponsored by mo on Patreon.
* init: When the repository already has a description, don't change it.
* describe: When run with no description parameter it used to set
the description to "", now it will error out.
Importing from a special remote honors its preferred content too; unwanted
files are not imported. But, some preferred content expressions can't be
checked before files are imported, and trying to import with such an
expression will fail.
Tested this with scenarios including changing the preferred content
expression and making sure merging the import didn't delete files that were
no longer wanted.
There was one minor inefficiency mentioned in the todo that I punted on.
Make the import have the previous import as a parent, so eg `git log --stat`
displays a useful diff.
Also a minor optimisation, only calculate the depth of the imported history
once.
This includes a note about how include= and exclude= match when exporting
a subtree. I don't know if the note is prominent enough, but the
behavior seems unsurprising enough.
Added the ability to run one job per CPU (core), by setting annex.jobs=cpus,
or using option --jobs=cpus or -Jcpus.
Built with future expansion in mind, including not defaulting matching on
Concurrency so more constructors can later be added, and using "cpu"
instead of "0".
Fixes bug that caused git-annex to fail to add a file when another
git-annex process cleaned up the temp directory it was using.
Solution is just to push withOtherTmp out to a higher level, so that
the whole ingest process can be completed inside it.
But in the assistant, that was not practical to do, since withOtherTmp runs
in the Annex monad and the assistant does not. Worked around by introducing
a separate temp directory that only the assistant uses for lockdown.
Since only one assistant can run at a time, it's easy to clean up that
directory of old cruft at startup.
Fix reversion in last release that caused wrong tree to be written to
remote tracking branch after an export of a subtree.
The invariant "commitsha should have the treesha as its tree"
was not met due to a bug. Guarantee it's met by catting the commitsha
to find its actual tree. A little bit slower, but this is not run often.
* Added mimeencoding= term to annex.largefiles expressions.
This is probably mostly useful to match non-text files with eg
"mimeencoding=binary"
* git-annex matchexpression: Added --mimeencoding option.
Switch listContents to being a proper CommandStart, so if it throws an
exception, it will be treated like any other command action that fails.
downloadImport apparently does not ever throw an exception,
and itself uses commandAction, so it can't be a CommandStart.
Fix bug that caused importing from a special remote to repeatedly download
unchanged files when multiple files in the remote have the same content.
Unfortunately, there's really no good way to remove a uniqueness constraint
from a sqlite database. The best that can be done is to make a new table
and copy the data over. But that would require using persistent's
migrations or raw sql, and I don't want to do either.
Instead, a sledgehammer approach: Renamed .git/annex/cid to
.git/annex/cids. When the new database doesn't exist, it will be populated
from the git-annex branch.
Noting deletes the old database. Don't want to delete it out from under
some long-running git-annex process that might be using it. It could
eventually be deleted. But this is such a new feature, probably few repos
have the database in any case.
As well as adding the necessary methods, a few other changes to the adb
remote:
* Use ".annextmp" extension for temp files, to avoid conflict with other
temp files.
* Stop using "echo $?" to get exit status of command inside adb.
There were two problems; first the "echo" just before it meant it was
always 0! And secondly, it seems kind of random on my phone whether it's
1 or 0, not dependant on whether the command seems to have succeeded.
protocol=https implies port=443 and
port=443 implies protocol=https
-- this was necessary because the existing configs set port=443, but
with a protocol setting, users will naturally want to use it, and then
there's no need for them to supply the default https port. So we keep
back-compat, add a nicer way to enable https, and also add support for
non-standard https ports.
In particular, when two files had the same content, and one was unlocked
and modified, with annex.thin that can corrupt the content of the
annex object, and so fsck on the other file should detect that.
getKeyStatus was relying on Database.Keys.getAssociatedFiles to tell
when a file is unlocked, but that can false positive because the
database can list old associated files.
Instead, separate out the case of unlocked object which has multiple
hardlinks when annex.thin is in use.
To support filenames starting with dashes.
To update the config of existing repositories, you can re-run git-annex init.
Perhaps it should check every time for the old config and update it, but
that has several problems:
- read-only repos
- unexpected commands like `git annex find` changing git configs
might be surprising behavior
Since filenames starting with dashes are not super common and the user can
re-init easily enough if their repo needs fixed, I went for the simplest
fix.
Users may want sync to only export, or only import and this is broadly
analagous to push and pull, so it makes sense to use the same
configuration for it.
The branch is only updated once the export is 100% complete. This way,
if an export is started but interrupted and so the remote does not yet
contain some of the files, an import will make a commit on the old
branch, and so won't delete the missing files.
This log, unlike all other current top-level logs, is a new format log.
I have not checked what throwing it at the old log parser did, but it seems
likely it ignored unparsable lines, and so perhaps deleted all lines from
the log.
This fixes a reversion in the ByteString conversion. The old code used
isSpace to decide when the metadata value needs to be base64 encoded,
and that incorrectly changed to only checking if it contained ' '.
Note that only '\n' and '\r' were added and not other sorts of
whitespace that isSpace matches, like '\t' and '\v'. Only the former
would cause problems.
Installing git-annex with stack rsync won't be available.
Also, using the git-annex installer with 64 bit git installs a non-working
rsync binary because it's linked with libraries provided by 32 bit git.
Like with the network-uri split, cabal will automatically turn off the flag
when building with an old network.
I have not tested building with the new network-3.0.0.0 yet; several
other dependencies including aws are still pinned on network-2.*
xporting files with '#' or '?' in their name won't work because urls get
truncated on those. Fail in a better way in this case, and avoid failing
when removing such files from the export, so after the user has renamed the
problem files the export will succeed.
Avoid performing repository fixups for submodules and git-worktrees
when there's a .noannex file that will prevent git-annex from being
used in the repository.
This change is ok as long as the .noannex file is really going to prevent
git-annex from being used. But, init --force could override the file.
Which would result in the repo being initialized without the fixups
having run.
To avoid that situation decided to change init, to not let --force be used
to override a .noannex file. Instead the user can just delete the file.
* fromkey: Added --json.
* fromkey --batch output changed to support using it with --json.
The old output was not parseable for any useful information, so
this is not expected to break anything.
If the worktree file already exists, and is annexed and uses the same
key, avoid failing, nothing needs to be done.
Had to add lookupFileNotHidden to handle the case where an adjust --hide-missing
is in use, and the worktree file was hidden due to the object content
being missing. lookupFile would return the key of the hidden file,
but it makes sense that after fromkey succeeds, the worktree must
contain the file it was supposed to set up.
Need to create the directory after the lock is held, not before.
The other racing process would need to shut down at just the wrong time,
running cleanupOtherTmp.
This commit was sponsored by Boyd Stephen Smith Jr. on Patreon.
This gets back any speed lost in commit
9cebfd7002, and speeds up all uses of S3
remotes that operate on them more than once.
This commit was sponsored by Brett Eisenberg on Patreon.
When key-based retrieval from a S3 remote with exporttree=yes
appendonly=yes fails, fall back to trying to retrieve from the exported
tree. This allows downloads of files that were exported to such a remote
before versioning was enabled on it.
This is useful at least for a transition for users who got into that
situation, so they can download content from their S3 remote. May want to
remove this in the future though, since normally trying to download the
second time is only extra work.
This commit was sponsored by Brock Spratlen on Patreon.
Like the earlier fixed one in Command.Export, it occurred when the same
tree was exported by multiple clones. Previous fix was incomplete since
several other places looked at the list of exported trees to detect when
there was an export conflict. Added a single unified function to avoid
missing any places it needed to be fixed.
This commit was sponsored by mo on Patreon.
Because when git-annex lacks S3 version IDs for files stored in the bucket,
deleting them would cause data loss.
Also because git-annex is not able to download unversioned objects from a bucket
when versioning=yes.
This also prevents setting versioning=no. While that would perhaps be
possible to do safely, it would add complexity, and would mean that if
the user accidentially did enableremote versioning=no, they would not be
able to undo it.
This commit was sponsored by Trenton Cronholm on Patreon.
Needs not yet released version 0.22 of aws library; with older versions
asks the user to configure the bucket versioning themselves.
Note that S3 endpoints that don't support versioning will cause putBucketVersioning
to throw an exception, so initremote will fail.
This commit was sponsored by Jake Vosloo on Patreon.
* webapp: Remove configurator for box.com repository, since their
webdav support is going away at the end of this January.
* webapp: Remove configurator for gitlab, which stopped supporting git-annex
some time ago.
This commit was sponsored by Brock Spratlen on Patreon.
However, rsync still won't work with 64 bit git and
this is still not the documented way to install it.
So, if both 64 and 32 are installed, go with 32.
And if neither git can be found, default to 32.
* Switch to using .git/annex/othertmp for tmp files other than partial
downloads, and make stale files left in that directory when git-annex
is interrupted be cleaned up promptly by subsequent git-annex processes.
* The .git/annex/misctmp directory is no longer used and git-annex will
delete anything lingering in there after it's 1 week old.
Also, in Annex.Ingest, made the filename it uses in the tmp dir be
prefixed with "ingest-" to avoid potentially using a filename used by
some other code.
This will speed up the common case where a Key is deserialized from
disk, but is then serialized to build eg, the path to the annex object.
It means that every place a Key has any of its fields changed, the cache
has to be dropped. I've grepped and found them all. But, it would be
better to avoid that gotcha somehow..
A keyName could contain "/", though this is unlikely and certianly only
ever could happen with WORM keys.
The change to addunused to escape that is no problem at all.
The change to VariantFile to escape it means that different versions of
git-annex could resolve a merge conflict differently in this case, which
is unfortunate. There would be different .variant files used, so the two
resolutions would themselves merge together without additional
conflicts, but the user would have to clean up the extra .variant
files.
Not likely to be any speed gain here, but this completes porting every
log file over.
And, it let me get rid of code copied from ghc and modified, so
simplifying the licensing.
This preserves the workaround for the old bug that caused NoUUID items
to be stored in the log, prefixing log lines with " ". It's now handled
implicitly, by using takeWhile1 (/= ' ') to get the uuid.
There is a behavior change from the old parser, which split the value
into words and then recombined it. That meant that "foo bar" and "foo\tbar"
came out as "foo bar". That behavior was not documented, and seems
surprising; it meant that after a git-annex describe here "foo bar",
you wouldn't get that same string back out when git-annex displayed repo
descriptions.
Otoh, some other parsers relied on the old behavior, and the attoparsec
rewrites had to deal with the issue themselves...
For group.log, there are some edge cases around the user providing a
group name with a leading or trailing space. The old parser would ignore
such excess whitespace. The new parser does too, because the alternative
is to refuse to parse something like " group1 group2 " due to excess
whitespace, which would be even more confusing behavior.
The only git-annex branch log file that is not converted to attoparsec
and bytestring-builder now is transitions.log.
Mostly didn't push the ByteStrings down very deep, but all of these log
files are not written to frequently at all, so slight remaining
innefficiency doesn't matter.
In Logs.UUID, removed the fixBadUUID code that cleaned up after a bug in
git-annex versions 3.20111105-3.20111110. In the unlikely event that a repo was
last touched by that ancient git-annex version, the descriptions of remotes
would appear missing when used with this version of git-annex. That is such minor
breakage, and so unlikely to still be a problem for any repos, that it was not
worth forward-porting that code to ByteString.
Tested on an older ghc by enabling MonadFailDesugaring globally.
In TransferQueue, the lack of a MonadFail for STM exposed what would
normally be a bug in the pattern matching, although in this case an
earlier check that the queue was not empty avoided a pattern match
failure.
This is not as efficient as using ByteStrings throughout, but converting
the String to ByteString is actually significantly faster than the old
parser.
benchmarking parse/old
time 9.657 μs (9.600 μs .. 9.732 μs)
1.000 R² (0.999 R² .. 1.000 R²)
mean 9.703 μs (9.645 μs .. 9.785 μs)
std dev 231.6 ns (161.5 ns .. 323.7 ns)
variance introduced by outliers: 25% (moderately inflated)
benchmarking parse/new
time 834.6 ns (797.1 ns .. 886.9 ns)
0.987 R² (0.976 R² .. 0.999 R²)
mean 816.4 ns (802.7 ns .. 845.1 ns)
std dev 62.39 ns (37.66 ns .. 108.4 ns)
variance introduced by outliers: 82% (severely inflated)
There is a small behavior change from the old parsePOSIXTime,
which accepted any amount of trailing whitespace after the timestamp.
That behavior was not documented, and it doesn't seem anything relied on it.
It used to display the "bad feed content" message indicating there were no
enclosures found, which was misleading when the http request for the feed
failed.
This commit was sponsored by Ewen McNeill on Patreon.
downloadUrl uses meteredFile, which sets up one progress meter,
and Remote.Web also uses metered, so two progress meters are displayed for
the same download.
Reversion introduced with the http-conduit switch in
c34152777b -- I don't know why the extra
call to metered was added there.
When -J is not used, the extra progress meter didn't display,
but an extra blank line did get output, which is also fixed.
This commit was sponsored by John Pellman on Patreon.
init: When --version=5 is passed on a crippled filesystem, use a v5 direct
mode repo as requested, rather than upgrading to v7 adjusted unlocked.
Fixed test suite on crippled filesystems, making it request --version=5
to test direct mode.
Deleting directories is one of the great unsolved problems of CS, thanks to
abominations like NFS lock files and Windows and races with other processes
cleaning up after themselves in the background. The gpg test harness
sometimes failed to delete its temp directory on NFS. Avoid the problem
class by not deleting it at all, and putting it inside the tmp repo being
tested. The test suite's more robust (and/or nonsensical) workarounds for
deleting its test dir will thus be used, hopefully avoiding the problem
until an OS finds a new way to violate POSIX and the laws of nature.
Note that this means that the .gnupg directory will be on whatever
filesystem the test suite is being run on, which may be a lesser quality
filesystem than gpg is really expecting. Gpg does not seem to need to
write sockets etc to there so this seems ok. The only known problem is
that if the filesystem forces a directory mode like 777, gpg will warn
about unsafe home directory perms, but it still works.
This fixes a bug with the numcopies counting when using sync --content.
It did not always pass the local repo uuid to handleDropsFrom, and so the
numcopies counting was off by one, and unwanted local content would only be
dropped when there were numcopies+1 remote copies.
Also, support dropping local content that has reached an
exporttree remote that is not untrusted (currently only S3 remotes
with versioning).
* Fix bug upgrading from direct mode to v7: when files in the repository
were already committed as v7 unlocked files elsewhere, and the
content was present in the direct mode repository, the annexed files
got their full content checked into git.
* Fix bug that caused v7 unlocked files in a direct mode repository
to get locked when committing.
This commit was sponsored by Nick Piper on Patreon.
When a file was already unlocked, but the annex object was present, the
upgrade process populated the unlocked file, but neglected to update the
index.
This commit was sponsored by Jochen Bartl on Patreon.
webdav: When initializing, avoid trying to make a directory at the top of
the webdav server, which could never accomplish anything and failed on
nextcloud servers. (Reversion introduced in version 6.20170925.)
This commit was sponsored by mo on patreon.
No deprecation warning at run time, just one on the man page.
One thing findref remains able to do that find cannot is to run in a bare
repo. Find was made to refuse to run in a bare repo because it seemed
confusing for it to not list any files ever in that situation. It would be
better for find --branch to work in a bare repo but not without --branch
but I don't currently have a way to do that.
Probably a better solution would be to make git-annex in a bare repo
default to --branch master or something like that instead of --all.
This commit was sponsored by Denis Dzyubenko on Patreon.
* findref: Support file matching options: --include, --exclude,
--want-get, --want-drop, --largerthan, --smallerthan, --accessedwithin
* Commands supporting --branch now apply file matching options --include,
--exclude, --want-get, --want-drop to filenames from the branch.
Previously, combining --branch with those would fail to match anything.
* add, import, findref: Support --time-limit.
This commit was sponsored by Jake Vosloo on Patreon.
When public access is used for the remote, it complained that the user
needed to set creds to use it, which was just wrong.
When creds were being used, it fell back from trying to use the version ID
to just accessing the key in the bucket, which was ok for non-export
remotes, but wrong for buckets.
In both cases, display a hopefully useful warning.
This should only come up when an existing S3 remote has been exported
to, and then later versioning was enabled.
Note that it would perhaps be possible to fall back from trying to use
retrieveKeyFile when it fails and instead use retrieveKeyFileFromExport,
which may work when S3 version ID is missing. But there are problems
with that approach; how to tell when retrieveKeyFile has failed due to this
rather than a network problem etc? Anyway, that approach would only work
until the file in the export got overwritten, and then it would no
longer be accessible. And with versioning enabled, the user wants old
versions of objects to remain accessible, so it seems better to warn
about the problem as soon as possible, so they can go back and add S3
version IDs.
This work is supported by the NIH-funded NICEMAN (ReproNim TR&D3) project.
Note that it does not prevent storing p2p access tokens or multicast
encryption keys, since those are not cached; the previous commit
established the distinction.
How well this works depends on how often getRemoteCredPair is called and
how expensive it is. In some cases setting this will result in an annoying
number of gpg password prompts and/or slowdowns due to reading creds
from the git-annex branch and decrypting, which could be improved by calling
getRemoteCredPair less often.
This commit was sponsored by Ilya Shlyakhter on Patreon.
dropunused: When an unused object file has gotten modified, eg due to
annex.thin being set, don't silently skip it, but display a warning and let
--force drop it.
This commit was sponsored by Ethan Aubin.
info: When used with an exporttree remote, includes an "exportedtree" info,
which is the tree last exported to the remote. During an export conflict,
multiple values will be listed.
This commit was sponsored by John Pellman on Patreon.
* init: When a crippled filesystem causes an adjusted unlocked branch to
be used, set repo version to 7, which it neglected to do before.
* init: When on a crippled filesystem, and the git version is too old
to use an adjusted unlocked branch, fall back to using direct mode.
This commit was sponsored by Ilya Shlyakhter on Patreon.
Seems that youtube-dl --get-filename on a playlist lists all the filenames
for the playlist, which can take quite some time. The code already only
took the first name, so --no-playlist can speed it up a lot.
This commit was sponsored by Brett Eisenberg on Patreon.
And added stack-lts-9.9.yaml to support old versions of stack.
The i386 ancient autobuilder needs stack-lts-9.9.yaml; the OSX autobuilder
may also use it for a while, and it's needed to build on eg debian stable.
That didn't actually happen, newer lts like that one are not supported
by the version of stack in Debian stable, used for the i386-ancient
autobuild, and generally I want git-annex to be buildable on stable
releases of linux distros etc. So stack.yaml is going to be stuck on old
versions for some time until some years after stack stops breaking backwards
compatability.
When a command is operating on multiple files and there's an error with
one, try harder to continue to the rest. (As was already done for many
types of errors including IO errors.)
This handles cases like lockContentForRemoval throwing an exception when
the content is already locked. Just because a drop of one file fails, does
not mean it shouldn't go on to try to drop other files.
I looked over uses of `giveup` in Command/*; there are too many to check
them all extensively, but none stood out as being problems that should let
one commandAction stop running other commandActions. Worst case, something
bad will happen and rather than stopping right away with an error,
git-annex will display multiple errors as it fails over and over on each
file. I don't think I ever really intended `error`/`giveup` to stop other
commandActions; this was a relic of old confusion over haskell exception
handling.
Test suite passes.
This commit was sponsored by Ethan Aubin.
* drop -J: Avoid processing the same key twice at the same time when
multiple annexes files use it.
This prevents a drop of a key conflicting with another drop of the same
key.
This commit was sponsored by Brock Spratlen on Patreon.
export, sync --content: Avoid unnecessarily trying to upload files to an
exporttree remote that already contains the files.
When the export was origianly made in one repo and now git-annex is
running in a different repo, the export database is not yet populated with
information about the exportLocation of files. So, it was trying to upload
the files to the export, even when it already contained them.
sync --content would first download the content from the export, and then
re-upload the content back.
And this also led to "not available" failures for each file that was not
locally present yet.
Fix: Just use checkPresentExport before uploading; if it succeeds update
the database.
This is a surprising oversight, it's possible it fixes a reversion because
I would have thought I'd have noticed this problem when originally
developing exporttree remotes.
This commit was sponsored by Jochen Bartl on Patreon.
When an export conflict prevents accessing a special remote, be clearer
about what the problem is and how to resolve it.
This commit was sponsored by Trenton Cronholm on Patreon.
Don't much like that there's no way to distinguish between having the whole
content and having an old version of the file that's bigger, but of course
resuming a http transfer can always yield the wrong result if the file on
the http server is changing, and git-annex will detect that when it
verifies the downloaded content.
This work is supported by the NIH-funded NICEMAN (ReproNim TR&D3) project.
Fix bash completion of "git annex" to propertly handle files with spaces
and other problem characters. (Completion of "git-annex" already did.)
This commit was sponsored by Jake Vosloo on Patreon.
Finishes the start made in 983c9d5a53, by
handling the case where `transfer` fails for some other reason, and so the
ReadContent callback does not get run. I don't know of a case where
`transfer` does fail other than the locking dealt with in that commit, but
it's good to have a guarantee.
StoreContent and StoreContentTo had a similar problem.
Things like `getViaTmp` may decide not to run the transfer action.
And `transfer` could certianly fail, if another transfer of the same
object was in progress. (Or a different object when annex.pidlock is set.)
If the transfer action was not run, the content of the object would
not all get consumed, and so would get interpreted as protocol commands,
which would not go well.
My approach to fixing all of these things is to set a TVar only
once all the data in the transfer is known to have been read/written.
This way the internals of `transfer`, `getViaTmp` etc don't matter.
So in ReadContent, it checks if the transfer completed.
If not, as long as it didn't throw an exception, send empty and Invalid
data to the callback. On an exception the state of the protocol is unknown
so it has to raise ProtoFailureException and close the connection,
same as before.
In StoreContent, if the transfer did not complete
some portion of the DATA has been read, so the protocol is in an unknown
state and it has to close the conection as well.
(The ProtoFailureMessage used here matches the one in Annex.Transfer, which
is the most likely reason. Not ideal to duplicate it..)
StoreContent did not ever close the protocol connection before. So this is
a protocol change, but only in an exceptional circumstance, and it's not
going to break anything, because clients already need to deal with the
connection breaking at any point.
The way this new behavior looks (here origin has annex.pidlock = true so will
only accept one upload to it at a time):
git annex copy --to origin -J2
copy x (to origin...) ok
copy y (to origin...)
Lost connection (fd:25: hGetChar: end of file)
This work is supported by the NIH-funded NICEMAN (ReproNim TR&D3) project.
Fix hang when transferring the same objects to two different clients at the
same time. (Or when annex.pidlock is used, two different objects to the
same or different clients.)
Could also potentially occur if a client was downloading an object and
somehow lost connection but that git-annex-shell was still running and
holding the transfer lock.
This does not guarantee that, if `transfer` fails for some other reason,
a DATA response will be made.
This work is supported by the NIH-funded NICEMAN (ReproNim TR&D3) project.
Not the first time this kind of test suite breakage has happened..
It would be good to avoid somehow it looking up from .t and finding a git
repo. But just running the test suite from time to time outside of
git-annex would also let me notice these before the distribution packagers
do.
This commit was sponsored by mo on Patreon.
That can leave other imported files not checked into git, because the git
command queue is not flushed when git-annex errors out. And since it only
happens once git-annex has concluded a feed is broken, it's an intermittent
bug, worst kind. Been seeing it for a while, only tracked down today.
Instead, by returning False, git-annex importfeed will cleanly shutdown and
still exit nonzero.
This commit was sponsored by Denis Dzyubenko on Patreon.
When readContent got Nothing from prepSendAnnex, it did not run its
callback, and the callback is what sends the DATA reply.
sendContent checks with contentSize that the object file is present, but
that doesn't really guarantee that prepSendAnnex won't return Nothing.
So, it was possible for a P2P protocol GET to not receive a response,
and appear to hang. When what it's really doing is waiting for the next
protocol command.
This seems most likely to happen when the annex is in direct mode, and the
file being requested has been modified. It could also happen in an indirect
mode repository if genInodeCache somehow failed. Perhaps due to a race
with a drop of the content file.
Fixed by making readContent behave the way its spec said it should,
and run the callback with L.empty in this case.
Note that, it's finee for readContent to send any amount of data
to the callback, including L.empty. sendBytes deals with that
by making sure it sends exactly the specified number of bytes,
aborting the protocol if it's too short. So, when L.empty is sent,
the protocol will end up aborting.
This work is supported by the NIH-funded NICEMAN (ReproNim TR&D3) project.
Cache high-resolution mtimes for improved detection of modified files in v7
(and direct mode).
Including on Windows.
With back-compat support so old low-res mtimes won't break anything, and
so the new information also won't break old versions of git-annex.
Removed undocumented special case in handling of a CHECKURL-MULTI response
with only a single file listed. Rather than ignoring the url that was in
the response, use it. This allows external special remotes that want to
provide some better url to do so, although I don't entirely agree with
using CHECKURL-MULTI to accomplish that. I'm more of the feeling that an
undocumented special case that throws data away is just not a good idea.
This could in theory break some external special remote program that relied
on the current behavior, but its seems unlikely that it would because such
a program must already handle the multiple url case, unless it only ever
provides a single url response to CHECKURL-MULTI.
Make addurl --file work with a single item CHECKURL-MULTI response.
It already did for external special remotes due to the special case,
but now it also will for builtin ones like the BitTorrent special remote.
This commit was sponsored by Ilya Shlyakhter on Patron.
This is safe, because while the annex object ends up executable,
there were already at least two other cases where it ended up executable:
1. git add an an executable file
2. chmod +x of a a non-executable worktree file that was hard linked to the
annex object
After copy/hard link, it always fixes up the permissions to match the mode
of the worktree file, so when an executable annex object gets hard linked
to a non-executable worktree file, its execute bit gets removed.
Commit b7c8bf5274 already *said* it would do
this; I suspect the line of code I've removed was included in that commit
accidentially.
Also improves annex.thin documentation.
This commit was sponsored by Boyd Stephen Smith Jr. on Patreon.
