This is conceptually very simple, just making a 1 that was hard coded be
exposed as a config option. The hard part was plumbing all that, and
dealing with complexities like reading it from git attributes at the
same time that numcopies is read.
Behavior change: When numcopies is set to 0, git-annex used to drop
content without requiring any copies. Now to get that (highly unsafe)
behavior, mincopies also needs to be set to 0. It seemed better to
remove that edge case, than complicate mincopies by ignoring it when
numcopies is 0.
This commit was sponsored by Denis Dzyubenko on Patreon.
No behavior changes (hopefully), just adding SeekInput and plumbing it
through to the JSON display code for later use.
Over the course of 2 grueling days.
withFilesNotInGit reimplemented in terms of seekHelper
should be the only possible behavior change. It seems to test as
behaving the same.
Note that seekHelper dummies up the SeekInput in the case where
segmentPaths' gives up on sorting the expanded paths because there are
too many input paths. When SeekInput later gets exposed as a json field,
that will result in it being a little bit wrong in the case where
100 or more paths are passed to a git-annex command. I think this is a
subtle enough problem to not matter. If it does turn out to be a
problem, fixing it would require splitting up the input
parameters into groups of < 100, which would make git ls-files run
perhaps more than is necessary. May want to revisit this, because that
fix seems fairly low-impact.
The hoped for optimisation of CommandStart with -J did not materialize.
In fact, not runnign CommandStart in parallel is slower than -J3.
So, CommandStart are still run in parallel.
(The actual bad performance I've been seeing with -J in my big repo
has to do with building the remoteList.)
But, this is still progress toward making -J faster, because it gets rid
of the onlyActionOn roadblock in the way of making CommandCleanup jobs
run separate from CommandPerform jobs.
Added OnlyActionOn constructor for ActionItem which fixes the
onlyActionOn breakage in the last commit.
Made CustomOutput include an ActionItem, so even things using it can
specify OnlyActionOn.
In Command.Move and Command.Sync, there were CommandStarts that used
includeCommandAction, so output messages, which is no longer allowed.
Fixed by using startingCustomOutput, but that's still not quite right,
since it prevents message display for the includeCommandAction run
inside it too.
The goal is to be able to run CommandStart in the main thread when -J is
used, rather than unncessarily passing it off to a worker thread, which
incurs overhead that is signficant when the CommandStart is going to
quickly decide to stop.
To do that, the message it displays needs to be displayed in the worker
thread, after the CommandStart has run.
Also, the change will mean that CommandStart will no longer necessarily
run with the same Annex state as CommandPerform. While its docs already
said it should avoid modifying Annex state, I audited all the
CommandStart code as part of the conversion. (Note that CommandSeek
already sometimes runs with a different Annex state, and that has not been
a source of any problems, so I am not too worried that this change will
lead to breakage going forward.)
The only modification of Annex state I found was it calling
allowMessages in some Commands that default to noMessages. Dealt with
that by adding a startCustomOutput and a startingUsualMessages.
This lets a command start with noMessages and then select the output it
wants for each CommandStart.
One bit of breakage: onlyActionOn has been removed from commands that used it.
The plan is that, since a StartMessage contains an ActionItem,
when a Key can be extracted from that, the parallel job runner can
run onlyActionOn' automatically. Then commands won't need to worry about
this detail. Future work.
Otherwise, this was a fairly straightforward process of making each
CommandStart compile again. Hopefully other behavior changes were mostly
avoided.
In a few cases, a command had a CommandStart that called a CommandPerform
that then called showStart multiple times. I have collapsed those
down to a single start action. The main command to perhaps suffer from it
is Command.Direct, which used to show a start for each file, and no
longer does.
Another minor behavior change is that some commands used showStart
before, but had an associated file and a Key available, so were changed
to ShowStart with an ActionItemAssociatedFile. That will not change the
normal output or behavior, but --json output will now include the key.
This should not break it for anyone using a real json parser.
This does not change the overall license of the git-annex program, which
was already AGPL due to a number of sources files being AGPL already.
Legally speaking, I'm adding a new license under which these files are
now available; I already released their current contents under the GPL
license. Now they're dual licensed GPL and AGPL. However, I intend
for all my future changes to these files to only be released under the
AGPL license, and I won't be tracking the dual licensing status, so I'm
simply changing the license statement to say it's AGPL.
(In some cases, others wrote parts of the code of a file and released it
under the GPL; but in all cases I have contributed a significant portion
of the code in each file and it's that code that is getting the AGPL
license; the GPL license of other contributors allows combining with
AGPL code.)
This is groundwork for nested seek loops, eg seeking over all files and
then performing commandActions on a list of remotes, which can be done
concurrently.
This commit was sponsored by Boyd Stephen Smith Jr. on Patreon.
Clean up some uses of showStart with "" for the file,
or in some cases, a non-filename description string. That would
generate bad json, although none of the commands doing that
supported --json.
Using "" for the file resulted in output like "foo rest";
now the extra space is eliminated.
This commit was sponsored by Fernando Jimenez on Patreon.
config group groupwanted numcopies schedule wanted required: Avoid
displaying extraneous messages about repository auto-init, git-annex branch
merging, etc, when being used to get information.
ghc 8 added backtraces on uncaught errors. This is great, but git-annex was
using error in many places for a error message targeted at the user, in
some known problem case. A backtrace only confuses such a message, so omit it.
Notably, commands like git annex drop that failed due to eg, numcopies,
used to use error, so had a backtrace.
This commit was sponsored by Ethan Aubin.
This is a work in progress. It compiles and is able to do basic command
dispatch, including git autocorrection, while using optparse-applicative
for the core commandline parsing.
* Many commands are temporarily disabled before conversion.
* Options are not wired in yet.
* cmdnorepo actions don't work yet.
Also, removed the [Command] list, which was only used in one place.
* numcopies: New command, sets global numcopies value that is seen by all
clones of a repository.
* The annex.numcopies git config setting is deprecated. Once the numcopies
command is used to set the global number of copies, any annex.numcopies
git configs will be ignored.
* assistant: Make the prefs page set the global numcopies.
This global numcopies setting is needed to let preferred content
expressions operate on numcopies.
It's also convenient, because typically if you want git-annex to preserve N
copies of files in a repo, you want it to do that no matter which repo it's
running in. Making it global avoids needing to warn the user about gotchas
involving inconsistent annex.numcopies settings.
(See changes to doc/numcopies.mdwn.)
Added a new variety of git-annex branch log file, that holds only 1 value.
Will probably be useful for other stuff later.
This commit was sponsored by Nicolas Pouillard.
