Fix bug in automatic merge conflict resolution code when used
on a filesystem not supporting symlinks, which resulted in it losing
track of the symlink bit of annexed files.
This was the underlying bug that was causing another test to fail,
which got worked around in 1c997fd08c.
I've chosen to keep 2 separate test cases since the old test case only
detected the problem accidentially.
Test suite passes on FAT & in windows, as well as on proper unix systems.
This commit was sponsored by Ellis Whitehead.
On windows, the sync of the second cloned repo to origin failed, because
synced/master was a non-fast-forward. This may be a bug of its own, but
it's not the issue that this test was intended to test, so disconnect
the repos from origin before syncing.
On Windows, a file that is not writable cannot be deleted even if in a
directory with write perms. So git object files were not getting deleted
when removing a git repository.
Need to include the uuid of the local repo in the list of belived locations
of a key after getting it, in order for the drop from remote to include it
in the numcopies calculation.
* sync --content: Honor annex-ignore configuration.
* sync: Don't try to sync with xmpp remotes, which are only currently
supported when using the assistant.
Seems that locking of annexed objects when they're being dropped was broken
in direct mode:
* When taking the lock before dropping, it created the .git/annex/objects
file, as an empty file. It seems that the dropping code deleted that,
but that is not right, and for all I know could in some situation cause
a corrupted object to leak out.
* When the lock was checked, it actually tried to open each direct mode
file, and checked if it was locked. Not the same lock used above, and
could also fail if some consumer of the file locked it.
Fixed this, and added windows support by switching direct mode to lock a
.lck file.
Make sanity checker run git annex unused daily, and queue up transfers
of unused files to any remotes that will have them. The transfer retrying
code works for us here, so eg when a backup disk remote is plugged in,
any transfers to it are done. Once the unused files reach a remote,
they'll be removed locally as unwanted.
If the setup does not cause unused files to go to a remote, they'll pile
up, and the sanity checker detects this using some heuristics that are
pretty good -- 1000 unused files, or 10% of disk used by unused files,
or more disk wasted by unused files than is left free. Once it detects
this, it pops up an alert in the webapp, with a button to take action.
TODO: Webapp UI to configure this, and also the ability to launch an
immediate cleanup of all unused files.
This commit was sponsored by Simon Michael.
Checking .gitattributes adds a full minute to a git annex find looking for
files that don't have enough copies. 2:25 increasts to 3:27. I feel this is
too much of a slowdown to justify making it the default. So, exposed two
versions of the preferred content expression, a slow one and a fast but
approximate one.
I'm using the approximate one in the default preferred content expressions
to avoid slowing down the assistant.
* Add numcopiesneeded preferred content expression.
* Client, transfer, incremental backup, and archive repositories
now want to get content that does not yet have enough copies.
This means the asssistant will make copies of files that don't yet
meet the configured numcopies, even to places that would not normally want
the file.
For example, if numcopies is 4, and there are 2 client repos and
2 transfer repos, and 2 removable backup drives, the file will be sent
to both transfer repos in order to make 4 copies. Once a removable drive
get a copy of the file, it will be dropped from one transfer repo or the
other (but not both).
Another example, numcopies is 3 and there is a client that has a backup
removable drive and two small archive repos. Normally once one of the small
archives has a file, it will not be put into the other one. But, to satisfy
numcopies, the assistant will duplicate it into the other small archive
too, if the backup repo is not available to receive the file.
I notice that these examples are fairly unlikely setups .. the old behavior
was not too bad, but it's nice to finally have it really correct.
.. Almost. I have skipped checking the annex.numcopies .gitattributes
out of fear it will be too slow.
This commit was sponsored by Florian Schlegel.
* numcopies: New command, sets global numcopies value that is seen by all
clones of a repository.
* The annex.numcopies git config setting is deprecated. Once the numcopies
command is used to set the global number of copies, any annex.numcopies
git configs will be ignored.
* assistant: Make the prefs page set the global numcopies.
This global numcopies setting is needed to let preferred content
expressions operate on numcopies.
It's also convenient, because typically if you want git-annex to preserve N
copies of files in a repo, you want it to do that no matter which repo it's
running in. Making it global avoids needing to warn the user about gotchas
involving inconsistent annex.numcopies settings.
(See changes to doc/numcopies.mdwn.)
Added a new variety of git-annex branch log file, that holds only 1 value.
Will probably be useful for other stuff later.
This commit was sponsored by Nicolas Pouillard.
Similar to the assistant, this honors any configured preferred content
expressions.
I am not entirely happpy with the implementation. It would be nicer if
the seek function returned a list of actions which included the individual
file gets and copies and drops, rather than the current list of calls to
syncContent. This would allow getting rid of the somewhat reundant display
of "sync file [ok|failed]" after the get/put display.
But, do that, withFilesInGit would need to somehow be able to construct
such a mixed action list. And it would be less efficient than the current
implementation, which is able to reuse several values between eg get and
drop.
Note that currently this does not try to satisfy numcopies when
getting/putting files (numcopies are of course checked when dropping
files!) This makes it like the assistant, and unlike get --auto
and copy --auto, which do duplicate files when numcopies is not yet
satisfied. I don't know if this is the right decision; it only seemed to
make sense to have this parallel the assistant as far as possible to start
with, since I know the assistant works.
This commit was sponsored by Øyvind Andersen Holm.
Known problems:
1. Tries to tahoe start when daemon is already running.
2. If multiple tahoe remotes are set up on the same computer,
they will have the same node.url configured by default,
and this confuses tahoe commands.
This commit was sponsored by LeastAuthority.com
