Anything that needs to examine the file content will fail to match,
or fall back to other available information. But the intent is that the
matcher be checked for matchNeedsFileContent and only be used if it does
not, so the exact behavior doesn't much matter as it should never
happen.
The real point of this is to not need to provide a dummy content file
when matching.
This commit was sponsored by Martin D on Patreon.
No behavior changes (hopefully), just adding SeekInput and plumbing it
through to the JSON display code for later use.
Over the course of 2 grueling days.
withFilesNotInGit reimplemented in terms of seekHelper
should be the only possible behavior change. It seems to test as
behaving the same.
Note that seekHelper dummies up the SeekInput in the case where
segmentPaths' gives up on sorting the expanded paths because there are
too many input paths. When SeekInput later gets exposed as a json field,
that will result in it being a little bit wrong in the case where
100 or more paths are passed to a git-annex command. I think this is a
subtle enough problem to not matter. If it does turn out to be a
problem, fixing it would require splitting up the input
parameters into groups of < 100, which would make git ls-files run
perhaps more than is necessary. May want to revisit this, because that
fix seems fairly low-impact.
Only supported by some special remotes: directory
I need to check the rest and they're currently missing methods until I do.
git-annex sync --no-content does not yet use this to do imports
The ContentIdentifier can contain almost anything, so could have characters
that are not fit for the filesystem, or might be longer than a key usually
is, or contain a newline, or .... genKeyName deals with those problems.
This should not present a back-compat issue, because this is a temporary
key used while downloading the imported file, before the real key for it
can be generated.
retrieveExport is part of ongoing transition to make remote methods
throw exceptions, rather than silently hide them.
getKey very rarely fails, and when it does it's always for the same reason
(user configured annex.backend to url for some reason). So, this will
avoid dealing with Nothing everywhere it's used.
This commit was sponsored by Ilya Shlyakhter on Patreon.
Adds a dependency on filepath-bytestring, an as yet unreleased fork of
filepath that operates on RawFilePath.
Git.Repo also changed to use RawFilePath for the path to the repo.
This does eliminate some RawFilePath -> FilePath -> RawFilePath
conversions. And filepath-bytestring's </> is probably faster.
But I don't expect a major performance improvement from this.
This is mostly groundwork for making Annex.Location use RawFilePath,
which will allow for a conversion-free pipleline.
This will speed up the common case where a Key is deserialized from
disk, but is then serialized to build eg, the path to the annex object.
Previously attempted in 4536c93bb2
and reverted in 96aba8eff7.
The problems mentioned in the latter commit are addressed now:
Read/Show of KeyData is backwards-compatible with Read/Show of Key from before
this change, so Types.Distribution will keep working.
The Eq instance is fixed.
Also, Key has smart constructors, avoiding needing to remember to update
the cached serialization.
Used git-annex benchmark:
find is 7% faster
whereis is 3% faster
get when all files are already present is 5% faster
Generally, the benchmarks are running 0.1 seconds faster per 2000 files,
on a ram disk in my laptop.
This solves the problem of sameas remotes trampling over per-remote
state. Used for:
* per-remote state, of course
* per-remote metadata, also of course
* per-remote content identifiers, because two remote implementations
could in theory generate the same content identifier for two different
peices of content
While chunk logs are per-remote data, they don't use this, because the
number and size of chunks stored is a common property across sameas
remotes.
External special remote had a complication, where it was theoretically
possible for a remote to send SETSTATE or GETSTATE during INITREMOTE or
EXPORTSUPPORTED. Since the uuid of the remote is typically generate in
Remote.setup, it would only be possible to pass a Maybe
RemoteStateHandle into it, and it would otherwise have to construct its
own. Rather than go that route, I decided to send an ERROR in this case.
It seems unlikely that any existing external special remote will be
affected. They would have to make up a git-annex key, and set state for
some reason during INITREMOTE. I can imagine such a hack, but it doesn't
seem worth complicating the code in such an ugly way to support it.
Unfortunately, both TestRemote and Annex.Import needed the Remote
to have a new field added that holds its RemoteStateHandle.
No behavior changes, but this shows everywhere that a progress meter
could be displayed when hashing a file to add to the annex.
Many of the places don't make sense to display a progress meter though,
eg when importing the copy of the file probably swamps the hashing of
the file.
The goal is to be able to run CommandStart in the main thread when -J is
used, rather than unncessarily passing it off to a worker thread, which
incurs overhead that is signficant when the CommandStart is going to
quickly decide to stop.
To do that, the message it displays needs to be displayed in the worker
thread, after the CommandStart has run.
Also, the change will mean that CommandStart will no longer necessarily
run with the same Annex state as CommandPerform. While its docs already
said it should avoid modifying Annex state, I audited all the
CommandStart code as part of the conversion. (Note that CommandSeek
already sometimes runs with a different Annex state, and that has not been
a source of any problems, so I am not too worried that this change will
lead to breakage going forward.)
The only modification of Annex state I found was it calling
allowMessages in some Commands that default to noMessages. Dealt with
that by adding a startCustomOutput and a startingUsualMessages.
This lets a command start with noMessages and then select the output it
wants for each CommandStart.
One bit of breakage: onlyActionOn has been removed from commands that used it.
The plan is that, since a StartMessage contains an ActionItem,
when a Key can be extracted from that, the parallel job runner can
run onlyActionOn' automatically. Then commands won't need to worry about
this detail. Future work.
Otherwise, this was a fairly straightforward process of making each
CommandStart compile again. Hopefully other behavior changes were mostly
avoided.
In a few cases, a command had a CommandStart that called a CommandPerform
that then called showStart multiple times. I have collapsed those
down to a single start action. The main command to perhaps suffer from it
is Command.Direct, which used to show a start for each file, and no
longer does.
Another minor behavior change is that some commands used showStart
before, but had an associated file and a Key available, so were changed
to ShowStart with an ActionItemAssociatedFile. That will not change the
normal output or behavior, but --json output will now include the key.
This should not break it for anyone using a real json parser.
Importing from a special remote honors its preferred content too; unwanted
files are not imported. But, some preferred content expressions can't be
checked before files are imported, and trying to import with such an
expression will fail.
Tested this with scenarios including changing the preferred content
expression and making sure merging the import didn't delete files that were
no longer wanted.
There was one minor inefficiency mentioned in the todo that I punted on.
Make the import have the previous import as a parent, so eg `git log --stat`
displays a useful diff.
Also a minor optimisation, only calculate the depth of the imported history
once.
Prevents merging the import from deleting the non-preferred files from
the branch it's merged into.
adjustTree previously appended the new list of items to the old, which
could result in it generating a tree with multiple files with the same
name. That is not good and confuses some parts of git. Gave it a
function to resolve such conflicts.
That allowed dealing with the problem of what happens when the import
contains some files (or subtrees) with the same name as files that were
filtered out of the export. The files from the import win.
bf7ecd6892 went too far and broke
importing, the old tree was used on the remote tracking branch and not
the newly imported tree.
Test suite noticed the problem luckily.
Fix reversion in last release that caused wrong tree to be written to
remote tracking branch after an export of a subtree.
The invariant "commitsha should have the treesha as its tree"
was not met due to a bug. Guarantee it's met by catting the commitsha
to find its actual tree. A little bit slower, but this is not run often.
This way no history is lost, neither what was exported to the remote,
or the history of changes that is imported from it. No complicated
correlation of two possibly very different histories is needed, just
record what we know and then git merge will do a good job.
Also, it notices when the remote tracking branch doesn't need to be updated,
and avoids doing anything, so noop remotes are super cheap.
The only catch here is that, since the commits generated for imports
from the remote don't have a stable date or author/committer, each
(non-noop) import generates different commits for the same imported
trees. So, when the imported remote tracking branch is merged into master
and then a change is imported again, there will be an extra series of
commits, which will get more and more expensive each time.
This seems to call for making stable commits for imports. Also that
seems a good idea to make importing in several repositories have the
same result.
Switch listContents to being a proper CommandStart, so if it throws an
exception, it will be treated like any other command action that fails.
downloadImport apparently does not ever throw an exception,
and itself uses commandAction, so it can't be a CommandStart.
untested
This won't be super slow, but it does need to diff two likely large
trees, and since the git-annex branch rarely sits still, it will most
likely be run at the beginning of every import.
A possible speed improvement would be to only run this when the database
did not contain a ContentIdentifier. But that would only speed up
imports when there is no new version of a file on the special remote,
at most renames of existing files being imported.
A better speed improvement would be to record something in the git-annex
branch that indicates when an import has been run, and only do the diff
if the git-annex branch has record of a newer import than we've seen
before. Then, it would only run when there is in fact new
ContentIdentifier information available from a remote. Certianly doable,
but didn't want to complicate things yet.
For now, it's only allowed when exporttree=yes is also set.
That simplified the implementation, but could later be changed if
there's a remote that makes sense to be an import but not an export.
However, it may work just as well to make a remote be readonly to
prevent export to it while still allowing import.
This does not avoid all possible races, but it does avoid all likely
ones, and is demonstratably better than git's own handling of races
where files get modified at the same time as it's updating the working
tree.
The main thing this won't detect are not unlikely races where part
of a file gets changed while it's being copied and then the file is
restored to its original condition before the modification check.
No, it's more likely that the limitations of checking inode, size,
and mtime won't detect certian modifications, involving eg mmapped
files.
Made some api changes.
listImportableContents needs to provide the size
of the data, so the downloader can check disk free space.
retrieveExportWithContentIdentifier is passed the filepath to write to
Use temporary "CID" key during download of a ContentIdentifier from a
remote, so withTmp can be used and then move the content to the real key
once it's known.
Added graftTree but it's buggy.
Should use graftTree in Annex.Branch.graftTreeish; it will be faster
than the current implementation there.
Started Annex.Import, but untested and it doesn't yet handle tree
grafting.
