proxyRequest was treating UNLOCKCONTENT as a separate request.
That made it possible for there to be two different connections to the
proxied remote, with LOCKCONTENT being sent to one, and UNLOCKCONTENT
to the other one. A protocol error.
git-annex testremote now passes against a http proxied remote.
The proxy always checks the protocol version of a remote before talking
to it in a version-specific way, so the protocol version in the ProxyParams
is the client's protocol version. The remote will always be at the same or
an older protocol version than the client.
Note that in relayDATAFinish, when the client is at protocol version 0,
the remote must thus be as well, and that's why its version is not
checked in the case for that.
With that clarified, it's evident that, in P2P.Http.State, there's no
need to look at the proxied remote's protocol version at all.
For clusters, the timestamps have to be translated, since each node can
have its own idea about what time it is. To translate a timestamp, the
proxy remembers what time it asked the node for a timestamp in
GETTIMESTAMP, and applies the delta as an offset in REMOVE-BEFORE.
This does mean that a remove from a cluster has to call GETTIMESTAMP on
every node before dropping from nodes. Not very efficient. Although
currently it tries to drop from every single node anyway, which is also
not very efficient.
I thought about caching the GETTIMESTAMP from the nodes on the first
call. That would improve efficiency. But, since monotonic clocks on
!Linux don't advance when the computer is suspended, consider what might
happen if one node was suspended for a while, then came back. Its
monotonic timestamp would end up behind where the proxying expects it to
be. Would that result in removing when it shouldn't, or refusing to
remove when it should? Have not thought it through. Either way, a
cluster behaving strangly for an extended period of time because one
of its nodes was briefly asleep doesn't seem like good behavior.
Before it was using a node that might have had a higher cost.
Also threw in a random selection from amoung the low cost nodes. Of
course this is a poor excuse for load balancing, but it's better than
nothing. Most of the time...
The VIA extension is still needed to avoid some extra work and ugly
messages, but this is enough that it actually works.
This filters out the RemoteSides that are a proxied connection via a
remote gateway to the cluster.
The VIA extension will not filter those out, but will send VIA to them
on connect, which will cause the ones that are accessed via the listed
gateways to be filtered out.
Except when no nodes want a file, it has to be stored somewhere, so
store it on all. Which is not really desirable, but neither is having to
pick one.
ProtoAssociatedFile deserialization is rather broken, and this could
possibly affect preferred content expressions that match on filenames.
The inability to roundtrip whitespace like tabs and newlines through is
not a problem because preferred content expressions can't be written
that match on whitespace such as a tab. For example:
joey@darkstar:~/tmp/bench/z>git-annex wanted origin-node2 'exclude=*CTRL-VTab*'
wanted origin-node2
git-annex: Parse error: Parse failure: near "*"
But, the filtering of control characters could perhaps be a problem. I think
that filtering is now obsolete, git-annex has comprehensive filtering of
control characters when displaying filenames, that happens at a higher level.
However, I don't want to risk a security hole so am leaving in that filtering
in ProtoAssociatedFile deserialization for now.
If the location log says all nodes contain content, pass in all nodes,
rather than none.
The location log can be wrong. While it's good to avoid unncessessary
connections to nodes that already contain a key, it would be bad to
refuse to accept an upload at all when the location log is wrong.
Also, passing in no nodes leaves the proxy in an untenable state. It
can't proxy to no nodes. So it closes the connection. Passing in all
nodes means it has to do the work to connect to all of them, and see
that they say they already have the content, and then it can tell the
client that.
Avoid `git-annex sync --content` etc from operating on cluster nodes by default
since syncing with a cluster implicitly syncs with its nodes. This avoids a
lot of unncessary work when a cluster has a lot of nodes just in checking
if each node's preferred content is satisfied. And it avoids content
being sent to nodes individually, so instead syncing with clusters always
fanout uploads to nodes.
The downside is that there are situations where a cluster's preferred content
settings can be met, but those of its nodes are not. Or where a node does not
contain a key, but the cluster does, and there are not enough copies of the key
yet, so it would be desirable the send it there. I think that's an acceptable
tradeoff. These kind of situations are ones where the cluster itself should
probably be responsible for copying content to the node. Which it can do much
less expensively than a client can. Part of the balanced preferred content
design that I will be working on in a couple of months involves rebalancing
clusters, so I expect to revisit this.
The use of annex-sync config does allow running git-annex sync with a specific
node, or nodes, and it will sync with it. And it's also possible to set
annex-sync git configs to make it sync with a node by default. (Although that
will require setting up an explicit git remote for the node rather than relying
on the proxied remote.)
Logs.Cluster.Basic is needed because Remote.Git cannot import Logs.Cluster
due to a cycle. And the Annex.Startup load of clusters happens
too late for Remote.Git to use that. This does mean one redundant load
of the cluster log, though only when there is a proxy.
Dropping from a cluster drops from every node of the cluster.
Including nodes that the cluster does not think have the content.
This is different from GET and CHECKPRESENT, which do trust the
cluster's location log. The difference is that removing from a cluster
should make 100% the content is gone from every node. So doing extra
work is ok. Compare with CHECKPRESENT where checking every node could
make it very expensive, and the worst that can happen in a false
negative is extra work being done.
Extended the P2P protocol with FAILURE-PLUS to handle the case where a
drop from one node succeeds, but a drop from another node fails. In that
case the entire cluster drop has failed.
Note that SUCCESS-PLUS is returned when dropping from a proxied remote
that is not a cluster, when the protocol version supports it. This is
because P2P.Proxy does not know when it's proxying for a single node
cluster vs for a remote that is not a cluster.
Client side support for SUCCESS-PLUS and ALREADY-HAVE-PLUS
is complete, when a PUT stores to additional repositories
than the expected on, the location log is updated with the
additional UUIDs that contain the content.
Started implementing PUT fanout to multiple remotes for clusters.
It is untested, and I fear fencepost errors in the relative
offset calculations. And it is missing proxying for the protocol
after DATA.
This assumes that the proxy for a cluster has up-to-date location
logs. If it didn't, it might proxy the checkpresent to a node that no
longer has the content, while some other node still does, and so
it would incorrectly appear that the cluster no longer contains the
content.
Since cluster UUIDs are not stored to location logs,
git-annex fsck --fast when claiming to fix a location log when
that occurred would not cause any problems. And presumably the location
tracking would later get sorted out.
At least usually, changes to the content of nodes goes via the proxy,
and it will update its location logs, so they will be accurate. However,
if there were multiple proxies to the same cluster, or nodes were
accessed directly (or via proxy to the node and not the cluster),
the proxy's location log could certainly be wrong.
(The location log access for GET has the same issues.)
