Actually the display in asus-me176c has a width of 800px, which means
that the splash screen isn't perfectly centered. Correct this in
deviceinfo to make it show up correctly.
Also, add configuration file for Phosh to reduce scaling a bit to 1.75.
It's kind of subjective but scaling = 2 definitely feels too large.
[ci:skip-build]: already built successfully in CI
There's a race condition between when the pwmled device is initialized,
which kicks off a feedbackd udev rule that configures the led trigger to
'pattern', and when ledtrig_pattern actually loads. It seems to mostly
load after the rule runs, so the trigger is never set to 'pattern' on
boot.
This removes the race by building the ledtrig_pattern driver into the
kernel.
[ci:skip-build] Already build successfully in CI
This patch fixes a fairly severe performance regression with wifi on the
L5 (something like 20x improvement in performance with this patch)
[ci:skip-build] Already build successfully in CI
Ship mode via the mechanism used by purism doesn't work; it's either not
possible or outside my understanding to run an openrc runscript with a
busybox init on *poweroff* and *not reboot*, which is what is required
for this to work properly..
This module param requires a corresponding kernel patch to enable ship
mode support in the bq25890-charger module
Upstream change logs:
5.11.2:
fdc91c4e20
5.11.4:
a178aa515c
This also adds a -dev subpackage, and cleans up makedepends
[ci:skip-build]: already built successfully in CI
This includes a new librem5-base config release, the most notable change
being some mic echo cancellation changes in pulseaudio config.
Upstream changelog:
351958ffc0
Note: I did not include the upstream change to disable wifi PM. I don't
find the performance to be so bad that it's worth giving up some battery
efficiency for.
Note: the librem5-base thing from purism has a new naming/versioning
format, which is in line with some of their other projects, so the
APKBUILD has been updated to support that too
This adds a new subpackage that installs dependencies and configures the
smartcard reader on the librem 5. Some setup is required before this
will work (e.g. upgrading reader firmware), the L5 wiki page will have
this information.
The pcsc init script was forked into this package to allow for powering
on the reader *before* the service started. Doing this in a separate
init script would have caused the reader to power on regardless of
whether the pcsc service was set to start, which is not desirable since
it should *only* be powered on when pcsc is starting
Purism has changed the kernel name they used, so that's reflected in the
apkbuild.
This kernel includes patches for renaming the audio device, and requires
a corresponding upgrade to the device package to bring in the new ucm2
config changes for that.
There is already samsung-a3ulte in community, and the devices actually
share the same kernel, device tree, and basically everything except
firmware. We just need separate firmware packages because Samsung uses
different secure boot certificates on a3lte and a3ulte.
They also share the same wiki page which suggests installation using
the pre-built images now, so having pre-built images only for
samsung-a3ulte is quite confusing for users.
The situation is similar as for samsung-a5ulte and samsung-a5lte
which also are both in community already.
According to Purism, the imx8mq-librem5.dtb alias is going away soon,
and we should be using the -r2 dtb. The -r2 dtb (which represents
Birch/Chestnut L5 variants) is most compatible, it'll boot on later
variants. dtbs for later L5 devices won't work on older devices.
- Upgrade librem5-base to v33
- Include the haptic vibration driver in initfs for supporting osk-sdl's
haptic feedback feature
- remove gps udev rule in pmaports in favor of using rule from
librem5-base
- install modem audio udev rule from librem5-base
- add openrc service for putting device into 'ship mode' on shutdown
(prevents battery from slowly draining)
- include Evergreen/r4 dtb in /boot
- Fix audio with port of ucm config to ucm2 (patch submitted upstream
here: https://source.puri.sm/Librem5/librem5-base/-/merge_requests/214)
The modprobe.conf is not necessary on those devices because they already
load the panel module using deviceinfo_modules_initfs. Let's skip the
modprobe.conf in that case so we don't need to add all panels in two places.
Upstream changelog:
868f3eb852
Suspend is also disabled in the kconfig, since it is not
supported/working on this device
[ci:skip-build]: already built successfully in CI
After pulseaudio 14.0 was released, audio on the pinephone was broken.
This applies the relevant config from here to fix it:
c23f92aa46
[ci:skip-build]: already built successfully in CI
New upstream ALSA/PulseAudio release, new UCM regressions - of course!
Introduce some new hacks to make the ALSA UCM configurations work again.
This fixes weird "Combination of Speaker,Primary Microphone" outputs
appearing in the PulseAudio mixer.
And while we're at it, some minor improvements/additions:
- Default to Speaker/PrimaryMic instead of Headphones/Headset
I believe this is just a workaround until headphones detection
works properly.
- Add UCM configurations for oppo-a51f and lenovo-a6010
Upstream keeps making breaking changes in patch releases.
Let's fork alsa-ucm-conf entirely for now instead of just patching
in some files to ensure that these files don't break every few months.
This fixes audio on MSM8916 devices when not using the modem.
This subpackage was removed when a proper fix for suspend was merged,
however apk doesn't know to purge this subpackage, so the old elogind
hook workaround stuck around. This workaround could probably be removed
once we're sure all folks on edge have installed this upgraded package
with the 'provides'...
- re-enable console suspend, which seems to be broken with elogind when
suspending (kernel gets hung up indefinitely in vt_waitactive)
- add a suspend hook to work around the musb driver not allowing the
device to suspend
Based on my testing, this option seems to prevent suspending via
elogind (using `loginctl suspend`). When console suspend is disabled,
the kernel gets hung up in the call to vt_waitactive, and elogind times
out trying to suspend.
This new version:
- Upgrades device config from upstream to v25
- Fixes a problem using modesetting driver on Xorg (lightdm
was broken because it now uses Xorg)
- Override GDK to use GLES (change from upstream Purism)
