uim-selection has "after *" in it's dependencies to make sure the
theoretical up to ~1min delay can't be observed. Unfortunaely this
causes incorrect dependencies ordering if one of other services depends
on ofono or modemmanager. Drop "after *" so modem can always be started
properly.
NymphCast is a FOSS Chromecast replacement (not a drop-in one though)
and allows you to "cast" audio and video to your device running the
nymphcast server. Plasma Bigscreen seems like an ideal use-case for this
so let's install and launch it by default. People can always uninstall
it anyways
Merged in mainline since 5.9-rc2-next-grate:
- all previously applied patches specific for Tegra and Nexus 7
New features, not merged yet in mainline (only in -next-grate):
- improved power management
- implemented USB OTG
New configuration options
- enable F2FS support (incl. compression), which leads to prolonging
eMMC life
Tested on E1565.
Signed-off-by: David Heidelberg <david@ixit.cz>
This allows using lm_sensors to read temperature data on the pinebook
pro (and probably other devices too)
❯ sensors
gpu_thermal-virtual-0
Adapter: Virtual device
temp1: +41.1°C (crit = +95.0°C)
tcpm_source_psy_4_0022-i2c-4-22
Adapter: rk3x-i2c
in0: 5.00 V (min = +5.00 V, max = +5.00 V)
curr1: 2.50 A (max = +2.50 A)
cw2015_battery-i2c-4-62
Adapter: rk3x-i2c
in0: 4.24 V
curr1: 0.00 A
cpu_thermal-virtual-0
Adapter: Virtual device
temp1: +47.5°C (crit = +95.0°C)
nvme-pci-0100
Adapter: PCI adapter
Composite: +31.9°C (low = -273.1°C, high = +80.8°C)
(crit = +80.8°C)
Sensor 1: +31.9°C (low = -273.1°C, high = +65261.8°C)
Sensor 2: +37.9°C (low = -273.1°C, high = +65261.8°C)
[ci:skip-build] Already built on CI
5.13.5 had some rockchip-related fixes in the changelog, so I figured
why not upgrade to it.
These patches from Manjaro seem to be the bare minimum required to get
usb-c charging and device peripherial support working again (external
display still doesn't work)
[ci:skip-build] already built successfully in CI
There's a generic udev rule to set group ownership of backlights to
'video', but it only runs on the ADD action, which seems to be too
late(?) since the backlight device is never owned by 'video' on boot.
This rule will run on CHANGE too, which might be overkill but seems to
get the job done. It's now possible to set the backlight brightness on
the PBP as a normal user.
llvm was left over from Martijn's efforts to reduce the kernel size
The drivers for external DP are enabled here, but all patches from
manjaro that deal with DP/typec alt mode, etc are dropped since they do
not solve anything on their own and may cause display instability
issues...
[ci:skip-build]: already built successfully in CI
prevent the creation of a fake NUMA node
saving a few CPU cycles each DRAM access:
[ 0.000000] NUMA: No NUMA configuration found
[ 0.000000] NUMA: Faking a node at ...
[ 0.000000] NUMA: NODE_DATA [mem 0xff9c2100-0xff9c3fff]
if you boot on QEMU make sure to review vCPU topology:
set socket to 1