In the Linux kernel, the ST-Ericsson NovaThor U8500 SoC is barely
ever mentioned under the "NovaThor" name, more common are names like
U8500, Ux500, ST-Ericsson, STE, ...
Let's rename the kernel package to linux-postmarketos-stericsson
to make that more clear. Also cleanup the APKBUILD a bit while we're
at it, HOSTCC is unneeded, remove unnecessary depends, ...
We cannot have two of them at the same time, most compiler would fail here
but for some reason our didn't.
However, it's better to just use one (the new one, or the old one). Enable
CONFIG_RTL8723CS_NEW, which is the new driver that made it to pine64
kernel since 5.5.
Signed-off-by: Danct12 <danct12@disroot.org>
[ci:skip-build]: already built successfully in CI
We should disable it by default and let the user to enable it
when they want it.
And currently it's causing problems where the backlight would
go very dark with it enabled on PinePhone.
Signed-off-by: Danct12 <danct12@disroot.org>
bq-paella allows running unsigned firmware from other devices.
We can use that advantage to replace some of the original firmware
with newer versions from other devices. The DB410c has updated WCNSS
firmware that reportedly improves WiFi/BT coexistence (i.e. behavior
when both WiFi/BT are active at the same time).
Depend on the virtual "firmware-qcom-msm8916-wcnss" package to give
the user the choice which firmware version they would like to run.
The newer version from "firmware-qcom-db410c-wcnss" is installed by
default (since it has a higher "provider_priority"), but the user
can choose to replace it by running "apk add firmware-bq-picmt-wcnss".
- Set fixed commit in "source" line to avoid future problems if some
change is pushed to the repository
- Add pmb:cross-native to build natively since these are just a few
copy operations
- Remove some unneeded `cd "$srcdir"` lines
- Avoid installing venus.mbn since this is just a combined version of
venus.mdt + venus.b*
- Split -wcnss subpackage into -wcnss and -wcnss-nv to allow replacing
the WCNSS firmware with a newer version from firmware-qcom-db410c
- Provide "firmware-qcom-msm8916-wcnss" to still allow switching to
the original firmware if wanted
- Install only WCNSS_qcom_wlan_nv.bin for aarch64 since the other
configuration files are only needed for downstream (armv7)
The WCNSS firmware from DB410c is also useful for other devices
that can run unsigned firmware (e.g. bq-paella) because it is newer
and reportedly has some WiFi/BT coexistence problems fixed.
To allow easy switching betwen the original firmware from the manufacturer
(firmware-bq-picmt-wcnss) and the newer firmware (firmware-qcom-db410c-wcnss)
we make both packages provide a virtual "firmware-qcom-msm8916-wcnss"
package. The newer version from firmware-qcom-db410c gets a higher
provider_priority so it is installed by default.
However, the user can choose to do "apk add firmware-bq-picmt-wcnss"
to get the original firmware from the manufacturer instead.
This release gets rid of the hacks needed for out-of-tree modules in the
previous version of calamares.
[ci:skip-build]: already built successfully in CI
Following discussions in
https://gitlab.com/postmarketOS/pmaports/-/issues/398, swclock has been
removed from postmarketos-base to avoid setting time incorrectly on
devices with a hardware clock. The various raspberry pi don't have
an hardware clock. This activate swclock back.
Fails to build, because extra-cmake-modules from Alpine is not available
for armhf. Its APKBUILD says "Blocked by qt5-qtdeclarative".
[ci:skip-vercheck]
Add common.get_upstream_branch() and use it instead of assuming "master"
as upstream branch.
Example: user forks v20.05 to v20.05_some-fix, then creates a merge
request. CI must use v20.05 as upstream branch, when comparing for
modified files etc.
This makes recording system audio very simple and feasible in a cross-device
manner since application-logic can always rely / forward ALSA audio to the
loopback device instead of a device-specific audio interface.
