We cannot have two of them at the same time, most compiler would fail here
but for some reason our didn't.
However, it's better to just use one (the new one, or the old one). Enable
CONFIG_RTL8723CS_NEW, which is the new driver that made it to pine64
kernel since 5.5.
Signed-off-by: Danct12 <danct12@disroot.org>
[ci:skip-build]: already built successfully in CI
This makes recording system audio very simple and feasible in a cross-device
manner since application-logic can always rely / forward ALSA audio to the
loopback device instead of a device-specific audio interface.
Disable modules for hardware that's impossible to connect to the
allwinner devices or older than the 90's this shrinks the size from 380
to 250MB.
Then it enables module compression so it shrinks from 250MB to 57MB.
Then the module stripping was enabled, shrinking it to 20MB
[ci:skip-build]: already built successfully in CI
We'll use the new RTL8723CS driver in the kernel tree instead
of using the one that we have to fetch from GitHub.
Signed-off-by: Danct12 <danct12@disroot.org>
Signed-off-by: Asriel Dreemurr <asriel.danctnix@gmail.com>
[ci:skip-build]: already built successfully in CI
[skip-ci]: just downloading all kernel sources takes about one hour
and ollieparanoid wants to merge it now. This already ran
successfully with [ci:skip-build] and [ci:skip-vercheck].
CONFIG_INPUT_UINPUT is needed for !1012
- linter fix: remove unneeded HOSTCC
- use downstreamkernel_package
- _abi_release was never used
- this package is only enabled for aarch64, so always use
modules_install dbts_install in package(), remove redundant
switch case
Currently, every LCDs inside their (our users) pocket are driving 3.3V,
meanwhile the LCD interface is meant to drive at ~2V.
This turns our LCDs into a timebomb that is ready to trigger at any moment,
killing the display.
Signed-off-by: Danct12 <danct12@disroot.org>
Current default is performance, and that is for sure not a great choice
for battery. We can experiment with ondemand as well, but based on docs,
conservative is recommended.
[ci:skip-build]: build takes too long
* Added display in final pinephone to the kernel
* Added getty
* Use RGB led to signify booting status in u-boot
* Enable CONFIG_GPIO_SYSFS
[ci:skip-build]: won't finish in time
This adds a seperate dts for the longts version of the devkit (which was
the un-inverted version before) and adds a shortts version which was
inverted before, but didn't exist in pmaports yet because I manually
edited the dts for every release.
This MR abuses the kernel switching feature to switch the dtb instead so
shortts/longts can be selected in the init step.
[ci:skip-build]: build won't finish in time
- main: postmarketos-mkinitfs: Add /run
Create the /run directory in the initramfs so that cryptsetup doesn't
crash on not being able to create /run/cryptsetup for lockfiles
- device: pine-dontbeevil: Remove workaround for touchscreen
- main: linux-postmarketos-allwinner: Implemented supplies for touchscreen
This uses a slightly newer commit from the kernel repo that implements
requesting a regulator in the touchscreen driver
- device: pine-dontbeevil: Remove ethernet from initramfs
This actually makes debugging more complicated since networkmanager wont
touch the ethernet adapter afterwards and the initramfs can be debugged
over uart
- temp/u-boot: sync APKBUILD with upstream and update to 2019.04
- main: linux-postmarketos-allwinner: Use 20190521 git version
* Fixed audio
* Fixed battery handeling
* Added fix for touchscreen not working for everyone
* Use newer upstream kernel
[ci:skip-build]: won't finish in time, Martijn made sure that it builds.
* Moved more PinePhone related kernel stuff to the upstream
* Added cma=256M so the CSI subsystem doesn't throw out-of-memory errors
when capturing at higher than 1280x720 resolutions (but it still hangs)
* Removed a lot of modules that get compiled for DVB tuners after
enableing the camera stuff.
[ci:skip-build]: doesn't finish in time
* Inverted the X-axis on the touchscreen
* Enabled the driver for the wifi/bluetooth chip and added it to the dts
* Added a horrible hack for making the touchscreen work
This also decreases the kernel version because the previous version I've
used was technically incorrect.
[ci:skip-build]: doesn't finish in time
* Created seperate DTB for the devkit named sun50i-a64-dontbeevil.dts so
it can easily be edited and the diff remains readable in gitlab
* Added patch to build the new dtb
* Added the ST LIS3MDL to the new dtb (Magnetometer)
* Added the SensorTek STK3335 to the new dtb (Proximity and ambient
light sensor)
* InvenSense MPU-6050 to the new dtb (Accelerometer and gyroscope)
* Added CSI bus and OV5640 camera
Remaining issues:
* The STK3310 module doesn't load automatically
* Camera doesn't want to capture but does show up as /dev/video0
[ci:skip-build]: doesn't finish in time
UART and SSH work and HDMI works in u-boot (just like the pine-a64lts).
It should work now with display and xorg/weston works directly after
installing. Plasma mobile doesn't work directly because both kms and
fbdev are enabled and kms doesn't work yet.
linux-postmarketos-allwinner: update to 5.0.0-rc3 with patches for this
devkit, tested on this device and on pinea64lts (the only other device
using the allwinner kernel).
[ci:skip-build]: won't finish in time
Add firmware-rtl8723bt package and Pine wifi and bluetooth firmware
subpackage.
[skip ci]: ollieparanoid will build this MR manually before merging, it
will probably not finish CI within one hour.
This is a followup to !109 (merged). Affected packages:
* device/linux-samsung-p4wifi
* device/linux-sony-tulip
* device/linux-teclast-x80pro
* main/linux-postmarketos-allwinner
* main/linux-postmarketos-mainline
* main/linux-postmarketos-qcom
* main/linux-postmarketos-stable
[skip ci] I have confirmed that all 7 kernels still compile.
* Added linux-postmarketos-allwinner kernel
* Added copy of alpines u-boot package with pine-a64lts support
* Changed postmarketos-mkinitfs to add the plain .dtb file to the boot partition
