Basic support for the Tolino Shine 2 HD ebook reader.
Waveform handling shares the same oddities as for the Kobo Clara HD
but the file epdc_E060SCM.fw from the IMX6SL BSP from NXP does also work.
The existing waveform from SD card is used.
Preferred way to install is to clone the internal SD, keeping the original
as a backup, install on that clone.
U-Boot is a more recent one than the factory u-boot, so devicetrees are nicely
supported. Kernel is the near mainline kernel also used by the Kobo Clara HD.
About Wifi: Handling of the configuration file for boards with brcmfmac is not
supported yet.
[ci:skip-build] already built successfully in CI
It makes more sense here as it's also signed by OnePlus (instead of
just Qualcomm) and is expected to be here since
linux-postmarketos-qcom-msm8998>=5.16.0_rc6.
This adds a firmware package firmware-shift-sdm845 containing
BT, GPU and WiFi firmware, which allows to enable hardware
acceleration to get phosh up and running.
Change-Id: Iaef46ccd51a756ad44642769e64202a7c534be9c
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
This MR removes the downstream kernel package linux-shift-axolotl
and uses linux-postmarketos-qcom-sdm845 instead, as it has
recently added support for the SHIFT6mq (axolotl).
Change-Id: I79427820686eb813cb21f57d6bddc0d2f7984b6a
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
Uses now DRM variant of EPDC driver. Updates will work automatically
without using special APIs.
Note:
/sys/class/graphics/fbcon/cursor_blink should probably be set to zero
to avoid battery draining if text console is displayed
[ci:skip-build] Already built on CI in MR
The downstream kernel provider does not exist any more (see
samsung-m0-downstream if you really want the vendor kernel), so remove
this as it is unused.
With selinux enabled, build fails with gcc-11 with multiple errors like this:
/home/pmos/build/src/android_kernel_oneplus_sm8250-0c1bed1067131a0bd3e56c1cbdd3473606c5a48a/out/../security/selinux/hooks.c:5553:(.text+0xb34): relocation truncated to fit: R_AARCH64_ADR_PREL_PG_HI21 against `.bss.rtic'
Selinux is not required for pmOS, so this change should be safe.
This cuts downloads in half as only the needed sources are downloaded.
It also makes the packages simpler and fixes a bug where the oneplus3t
subpackage was overwriting the 20-adreno-gpu-firmware.files of the
oneplus3 subpackage.
Based on !1158 by @nrdnandan (5 files)
new file: device/testing/device-xiaomi-rolex/APKBUILD
new file: device/testing/device-xiaomi-rolex/deviceinfo
new file: device/testing/linux-xiaomi-rolex/APKBUILD
new file: device/testing/linux-xiaomi-rolex/config-xiaomi-rolex.aarch64
new file: firmware/firmware-xiaomi-rolex/APKBUILD
Changed deviceinfo : Width x Height was 800x600 to correct dimension -> 720x1280
modified: device/testing/device-xiaomi-rolex/APKBUILD
modified: device/testing/device-xiaomi-rolex/deviceinfo
Added directfbrc and fb.modes file. Also added SWAP file support swap_size=1024
Added Audio files and rules removed uneccessary lines in deviceinfo.
device/xiaomi-rolex: Fix linting issues
xiaomi-rolex: Linting fixes; is a handset
xiaomi-rolex: Moved firmware/ to device/testing/
xiaomi-rolex: Enable pmb:cross-native for kernel compilation
because it is the default for recent apkbuilds
xiaomi-rolex: Apply YYLOC patch to build 3.18.140 with gcc-10 (-fno-common)
xiaomi-rolex: update patch checksums in kernel APKBUILD
xiaomi-rolex: update deviceinfo checksum; replace common patch with a symlink
xiaomi-rolex: use mdss patch
xiaomi-rolex: use BGRA mdss framebuffer patch
xiaomi-rolex: mark myself as maintainer, drop contributor from apkbuilds
Refer to git commit history instead to determine contributors
xiaomi-rolex: update kernel config for multiple devpts
xiaomi-rolex: allow firmware cross-native builds, disable tracedeps per linter
[ci:skip-build]: already built successfully in CI
Remapping the left key of tm2-touchkey to KEY_MENU.
The KEY_APPSELECT, which is set by the device tree, is not available in
the postmarketOS UIs. In X11 UIs this is due to keycode limitation to
8 bit. In Wayland UIs the keycodes don't have this limitation but xkb
keycodes higher 255 are not processed correctly by several software
packages. It still makes sense to keep KEY_APPSELECT in the device tree
because this is the correct mapping intended by the manufacturers when
running the kernel on Android.
Kernel defconfig is a copy of "axolotl_userdebug_defconfig".
Config changes (which differ from the copy above):
- ran `pmbootstrap kconfig check shift-axolotl`
- CONFIG_QCA_CLD_WLAN - m -> y
Change-Id: Ie250ba0d4f7cabf516e4c4fef84a3832321fb069
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
[ci:skip-build]
The mainline-modem variant does not actually exist yet and this should
be preferably implemented using the new soc-qcom-msm8916-rproc selection
in the future.
Now the user can choose to install the proprietary firmware along with
the downstream or a (close to) mainline kernel.
[ci:skip-build]: already built successfully in CI
Add proprietary firmware required by OnePlus 5/5T's WLAN, Bluetooth, GPU
and other SoC subsystems such as ADSP. These are extracted directly from
OnePlus' OxygenOS 10.0.1 stock firmware with oos_fw_extract in the repo.
Now the user can choose to install the proprietary firmware along with
the downstream kernel (linux-huawei-angler) or a mainline kernel
(linux-postmarketos-qcom-msm8994).
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
[ci:skip-build] Already built on CI in MR
While it doesn't make sense to package a mainline kernel for FP1 (only
UART and basic SoC components supported), it's good to include the dtb
name in deviceinfo so external tools can use it.
Enable flashing kernel on update + small cleanups for deviceinfo:
* re-sort lines in deviceinfo
* remove console=tty0 from kernel cmdline, so it does not spit out
all kernel logs on the screen. Now during boot you see just
blinking cursor and pmOS logo.
Rule D: Devices with secure boot and venus present in the firmware
partition need:
1. GPU firmware (firmware-qcom-adreno-a300)
2. msm-firmware-loader (for wcnss, modem, venus)
4. device-specific -wcnss-nv firmware
[ci:ignore-count]
[ci:skip-build] already built successfully in CI
Squash the packaged venus firmware blobs using pil-squasher so only
one file needs to be loaded rather than many small ones. Linux detects
squashed (.mbn) vs non-squashed (.mdt + .b*) based on file contents
(not file name) so it is fine to install venus.mbn to venus.mdt.
Make the package consistent with firmware-qcom-adreno packaged from
linux-firmware, but keep them separate for legal reasons. The firmware
packaged in firmware-qcom-adreno-extra does not have a proper license.
[ci:ignore-count]
[ci:skip-build] already built successfully in CI
The firmware provided by these subpackages is now covered by the
msm-firmware-loader, so there is no need to build packages for them
anymore.
[ci:ignore-count]
The files packaged in firmware-motorola-osprey-wcnss-nv and
firmware-motorola-osprey-venus seem completely identical to those
of harpia, so there is no need to package them twice. There are some
differences in modem/wcnss firmware but those are now covered by the
msm-firmware-loader.
Add sony-fusion3 firmware subpackage to enable wifi.
Enable Qoalcomm Prima WLAN driver and fix wrong path in kernel.
[ci:skip-build] Already built on CI in MR
Touchscreen and usb networking works. Much of the hardware is the
same as on gts210velte (but that one has a qcom soc and not
exynos5433). Exactly the same touchscreen calibrarion as for
gts210velte works for this device as well.
Also include firmware package with wifi files. Unlike on many other
Samsung devices wifi does not work out of the box after these
firmware files has been added.
[ci:skip-build] Already built on CI in MR
I'm not sure it is possible to connect a second display to this phone
through P2P WiFi, so mapping cursor to DSI-1 just in case. It is needed
for screen rotation when a second display is connected.
Reduce scaling factor from default 2 to 1.8.
I'm not sure it is possible to connect a second display to this phone
through P2P WiFi, so mapping cursor to DSI-1 just in case. It is needed
for screen rotation when a second display is connected.
Reduce scaling factor from default 2 to 1.8.
