If (a) the kernel command line parameters include PMOS_BOOTCHART2 and
(b) /sbin/bootchartd exists (i.e., the bootchart2 package has been
installed), run /sbin/bootchartd instead of /sbin/init.
Port bootchart2 to PostmarketOS, with three patches:
1. Modification of /etc/bootchartd.conf so that the collector
will stop after sshd has started.
2. Python 3.8 compatibility
3. Disable the interactive mode of pybootchartgui.
Use bootchart2 to profile system boot or a running system.
1. Add the bootchart2 package to your device.
2. Add the following kernel command line parameters: initcall_debug
printk.time=y quiet
3. To profile system boot
a. add the following kernel command line parameter: PMOS_BOOTCHART2.
This parameter causes mkinitfs to start /sbin/bootchartd instead of
/sbin/init. /sbin/bootchartd then starts /sbin/init.
b. (optional) modify EXIT_PROC in /etc/bootchartd.conf to define
when the collector is to stop.
c. Boot the system. Approximately 20 seconds after sshd starts
(if using the default value of EXIT_PROC), the collector
will exit.
4. To profile a running system
a. use the command '/sbin/bootchartd start' (as root) to start
profiling
b. use the command '/sbin/bootchartd stop' (as root) to stop
profiling
5. When the collector exits, /usr/bin/pybootchartgui will create
a visualization in /var/log/bootchart.png.
- Update to Linux 5.5-rc4
- Fix freeze/crash when accessing reserved memory on Samsung devices
- This happened e.g. when doing large eMMC writes
because the disk cache filled all available RAM.
- Fix SD card detection on samsung-serranovelte
- Disable UHS-1 modes since they appear to be broken in hardware
[ci:skip-build]: already built successfully in CI
Comment out the initstepslew line in /etc/chrony/chrony.conf.
initstepslew can delay booting while chrony sets the time. The
makestep 1 -1 line in the configuration also causes chrony to step
the time (whenever the offset is greater than 1s), making
initstepslew redundant.
Unfortunately, early firmware versions on MSM8916 (used together with
Android 4.4) are not capable of booting aarch64 kernels. MSM8916 was
Qualcomm's first 64-bit capable CPU, and back when it was introduced
Android did not even support aarch64 yet. So the aarch64 capable
hardware was usually used together with armv7 binaries.
To make things worse, this firmware is also signed (usually per-device),
making it (currently) impossible to update it without help from the manufacturer.
This means that we are currently unable to run mainline on devices
that never received an update to Android 5.0
(e.g. the Samsung Galaxy S4 Mini Value Edition).
One way to circumvent this limitation is to build mainline for armv7.
This works surprisingly well with some additional fixes.
Devices with this firmware limitation are still unable to use aarch64
binaries, but at least we can run mainline on them!
- Rebase on Linux 5.5-rc3
- Add display, touchscreen and GPIO keys for samsung-gt510wifi
- Add vibrator for wileyfox-crackling
- Zinitix touchscreen improvements (used in samsung-a3ulte)
- Upstreamed several patches
Current default is performance, and that is for sure not a great choice
for battery. We can experiment with ondemand as well, but based on docs,
conservative is recommended.
[ci:skip-build]: build takes too long
On some devices a getty should run on the serial console.
Configure the getty by setting the deviceinfo_getty variable. The
format is "<port>;<baud rate>". For example, "ttyS0;115200".
A post-installation trigger in postmarketos-base checks
/etc/deviceinfo, and modifies /etc/inittab if the device should run
a getty.
Fix the following error when installing postmarketos-ui-plasma-mobile:
ERROR: unsatisfiable constraints:
polkit-elogind-0.116-r1:
breaks: polkit-dev-0.116-r0[polkit=0.116-r0]
satisfies: polkit-kde-agent-1-5.17.3-r0[polkit-elogind]
.pmbootstrap-20191121.210534[polkit-elogind]
consolekit2-1.2.1-r1[polkit]
consolekit2-1.2.1-r1[so:libpolkit-gobject-1.so.0]
networkmanager-1.20.6-r0[so:libpolkit-agent-1.so.0]
networkmanager-1.20.6-r0[so:libpolkit-gobject-1.so.0]
polkit-qt-1-0.113.0-r0[so:libpolkit-agent-1.so.0]
polkit-qt-1-0.113.0-r0[so:libpolkit-gobject-1.so.0]
accountsservice-0.6.55-r0[so:libpolkit-gobject-1.so.0]
urfkill-0.5.0_git20170118-r0[so:libpolkit-gobject-1.so.0]
This is the reason, why the pmbootstrap qemu test (which performs a full
plasma mobile installation and checks running processes) check failed:
https://postmarketos.gitlab.io/-/pmbootstrap/-/jobs/357942365/artifacts/log_testsuite.txt
Enable armhf again, because "gnome-session" is available in Alpine for
armhf now.
[ci:skip-build]: already built successfully in CI. ollieparanoid made
sure that all packages build for armhf.
[ci:skip-vercheck]
Signed-off-by: David Heidelberg <david@ixit.cz>
It seems the the CFLAGS are not properly set in the CMakeLists.txt.
Cmake currently appends -std=gnu90 at the end of the CFLAGS, overriding
the earlier set -std=c99. Work around this with sed. Better fix is
welcome, this is a stop-gap solution to unbreak the build (which is
blocking build.postmarketos.org).
It's unmaintained both on our side and upstream. Nobody stepped up to
maintain it (https://gitlab.com/postmarketOS/pmaports/issues/372), so
let's drop it before it introduces security issues and compilation
problems.
