Quite a few things use dbus (plasma, hildon, ofono, connman,
networkmanager, etc) that I think it makes sense to just have this
started by default in pmOS rather than have every device package
implement this on their own.
In case someone shows up with a use-case, where dbus by default
is not desired, please speak up. Possible solutions are in #628.
* Started with stock kernel config (fairphone-perf_defconfig)
* Enabled DEVTMPFS
* Deactivated MSM_KGSL
* Enabled the serial console
* Enabled USB networking
This adds a custom swap file service, which allows specifying a
recommended swap size in the deviceinfo file via
`deviceinfo_swap_size_recommended`. For the N900 this defaults
to 1024 MB now. As the swap file is created in the root partition,
we have encrypted swap now (unless encryption is disabled with
`--no-fde`).
This is a workaround for #429, until the iteration count can be
specified directly in cryptsetup.
* Add default iter-time option, and option to override
* set SHA1 default hash for luksFormat, add option to override
* [RX51] load omap-sham in initramfs for HW accel. sha1
* Add LG G Watch (dory) support
* Use github.com mirror instead of googlesource.com to have fixed checksum
* Fix kernel compilation and remove unnecessary initfs-hook for framebuffer settings
* Check kernel config
* Allow specifying multiple kernel packages, and also no packages
which defaults to scanning all kernel configs (it is super fast
anyway)
* Add the check to Travis CI
* Adjust existing kernel configs, so they pass the kconfig_check.
(We've had to put in a lot of defaults in the aarch64
linux-postmarketos configs, that's why the diff is a bit unclean.)
* Increase modified kernel pkgrels
- Revert to LineageOS 14.1 kernel
- Enable virtual terminal
- Update touchscreen settings
At the moment, display output works, but only when the following is run:
while [ ! ]; do cat /sys/class/graphics/fb0/modes >
/sys/class/graphics/fb0/mode; done.
Adding INSTALL_MOD_STRIP will cause modules to be stripped after
they are installed (option --strip-debug will be used)
In case someone isn't happy with it, please open a PR that reverts
it for your device, or start a discussion as a new issue.
* No need to append DTB to kernel
* Remove kernel module build for now
* Add device-specific firmware package
* Add special partitions to fstab
* Fix typo in screen width
* Add maguro wifi support
* enable framebuffer and VT, WESTON STARTS
* make touchscreen work & fix merge conflict
Cherry-pick of lawl's commit, ed552e5d9272204c12f67bcb0401b3e08e57d35f.
* Initial Mozilla Flame packages
* Update dtbtool to use LineageOS upstream
* Use mkbootimg --dt flag only when deviceinfo_bootimg_qcdt is defined
* Update mkbootimg to use LineageOS upstream
* Add sparse image flashing on device-mozilla-flame
* Only support SD card install on Mozilla Flame
* Remove useless profile.sh on mozilla flame
* Package DTBs in /usr/lib/linux-mozilla-flame/
* Build and install modules in linux-mozilla-flame
Thanks to Pablo Castellano and Martijn Braam!
In postmarketOS we are now able to generate system images with the
correct configuration so that they can boot already using qemu
This commit brings the `pmbootstrap qemu` action.
This command is very handy because you don't have to set all the
qemu parameters, pmbootstrap does it for you.
* device-qemu-vexpress: Added kernel command line according to wiki
* qemu: Added workaround for image writing permissions
* qemu: Added support to launch postmarketOS in a QEMU virtual machine
- Support for emulating these architectures in QEMU: arm, aarch64, x86_84
- Generate QEMU command correctly depending no guest architecture (arm/x86)
- Run QEMU in the same architecture as the host by default
- Refactoring in pmb.parse.arch and pmb.qemu.run
- Raise exception if DTB file or system image are not present
- Display more useful information when something fails (e.g. image not found)
- Run qemu version depending on arch (host or argument), not device configured
* device-qemu-amd64: set deviceinfo_kernel_cmdline to "PMOS_NO_OUTPUT_REDIRECT"
* qemu: added --memory argument to specific guest RAM
* device-qemu-amd64: adjusted deviceinfo_kernel_cmdline (console=tty1)
* Added /etc/network/interfaces for qemu-amd64
* qemu: Added KVM support if /dev/kvm if present
* Specify separate machines for architecture
* qemu: Check if QEMU is installed instead of crashing
* Added graphics driver to qemu-aarch64
- Use arm (as used in qemu) instead of armhf (used in Alpine)
- qemu argument is -dtb
- Follow same style to build the command + arguments
* qemu: Added SSH port redirection: ./pmbootstrap.py qemu -p 2222
* Packaged libsparse
libsparse from the Android project provides multiple tools like img2simg
and simg2img.
These are used to split a large image for the system partition into
separate smaller chunks with sparse headers
This is required for several devices (at least bullhead, fp2 and titan)
because it fixes the "Invalid sparse file format at header magi" error
https://github.com/postmarketOS/pmbootstrap/issues/299
* Added new variable deviceinfo_flash_sparse (fixes#299)
Right after the system image is generated, pmbootstrap checks this
variable. In case it is true, run img2simg on it
* motorola-titan: enable deviceinfo_flash_sparse
* libsparse: use source from github: anestisb/android-simg2img
It is not that easy to use the upstream archive because everytime
you download it, the files have the current date as creation date
and that makes the file have a different checksum every download
https://github.com/postmarketOS/pmbootstrap/pull/303#issuecomment-319017197