This is a version bump for the sm6125 mainline kernel fork.
Changes:
* Added UFS nodes to the sm6125 platform
* Enabled UFS nodes for xiaomi-laurel
* Enabled configs required for UFS support (Notoriously
CONFIG_PHY_QCOM_QMP)
* Filled in EXTRAVERSION for kernel fork
* Added SMD RPM regulators for xiaomi-laurel
Signed-off-by: Lux Aliaga <they@mint.lgbt>
[ci:skip-build]: Already built successfully in CI
Fix included in this build:
- Patch which sets GPIO pin for stk3311 as input
- ppp: don't reset 'display state of charge' (dsoc) to 0 on vbat low interrupt
[ci:skip-build]: already built successfully in CI
This upgrade has no effect on postmarketOS, as there were only systemd
service files added to the repository. The upgrade is done solely to
keep track with the newest version.
[ci:skip-build] already built successfully in CI
Update the omap kernel to stable 6.1 release. This commit also contains a patch that
fixes broken usb, which should only be needed for versions 5.19 to 6.1 as later
releases will have a proper fix merged.
[ci:skip-build]: already built successfully in CI
This is an early mainline port for the MediaTek MT6763 Helio P65/G70/G8*
SoCs that boots with all 8 cores online, logs on display (simplefb) or
UART serial console, USB gadget mode facilitating netbooting
postmarketOS while tethered via RNDIS and PMIC enabling functions like
vibrator, power/volume keys.
Since I'm not going by the "mint" alias anymore, I've decided to fix
that on the APKBUILDs
Signed-off-by: Lux Aliaga <they@mint.lgbt>
[ci:skip-build]: Already built successfully in CI
This is a version bump for the sm6125 mainline kernel fork. It should
also fix a config issue.
Changes:
* Made QUSB2 built-in instead of a module (Fixes USB connectivity
issues)
* Updates to xiaomi-laurel device tree to fit new schema
* Changed maintainer name
Signed-off-by: Lux Aliaga <they@mint.lgbt>
This fixes gnss out of the box on the librem 5, by configuring geoclue
to use gnss-share as a nmea source.
I went this route, of overriding a .service file that invokes geoclue
with a command line option, because forking this .service file is much
nicer than forking geoclue.conf. The conf file will likely change over
time to add new app permissions or whatever, and it's unlikely
(hopefull!) that this .service file will change much upstream...
[ci:skip-build] already built successfully in CI
CONFIG_USB_GADGET=y
CONFIG_USB_DWC3_DUAL_ROLE=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_PLATFORM=y
CONFIG_USB_DWC2=y
remove un-necessary activated configs
[ci:skip-build]: already built successfully in CI
Add rules for regulator-haptic, which is used on:
- samsung-e5/e7
- samsung-cprime/gprime
- samsung-j3/j5(x)
Note that regulator-haptic is not supported on some devices yet,
and samsung-e5 is not ported at the moment.
[ci:skip-build]: already built successfully in CI
- Also enabled LRU_GEN by default like on the PinePhone OG
- Set Ext4 module to built-in as this currently is the main fs used for PPP.
Contains the following patch:
- pinephone pro: finished fix for LCD to make it refresh at precisely 60 Hz
[ci:skip-build]: already built successfully in CI
Add new patches:
- enable serial console
- save relocation address to find KASLR
- buttons as keyboard input driver to navigate bootmenu
- bootmenu loop entry selection
Apparently upstream names udev rules with the .udev extension... which
doesn't work with udev (I guess debian has a helper for installing rules
and it renames them?). This adds the expected ".rules" extension to them
so that udev actually uses them.
This update also includes improved ucm config from Purism.
"Lockdown suppport" is also added here, which allows toggling off all of
the hks on the L5 to disable all radios, etc without breaking some
sensors. For more info, see 65ec7038 in librem5-base.
Based on some new (to me...) info from Purism's Sebastian K, there are
apparently Evergreen devices that return different values for board rev,
so we shouldn't assume only r4 are Evergreen, and default to the r2 DT.
But many earlier devices (Birch, Chestnut, Dogwood) may or may not have
the board rev set either. Who knows! Defaulting to the Evergreen DT on
these devices is bad too, but there weren't many of those shipped (I
guess?), at least not compared to the number of Evergreens that aren't
properly identifiable in u-boot... so this using this DT by default is
the best of the two bad options we have.
This comment thread has more info:
https://gitlab.com/postmarketOS/pmaports/-/issues/1643#note_1147248594fixes#1643
[ci:skip-build] already built successfully in CI
Add the CONFIG_DW9714 symbol to the PinephonePro defconfig.
The PinephonePro rear camera module uses the DW9714 VCM to drive the
lens, and a driver is required to successfully complete the media
graph probe sequence.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
