Store the full kernel config instead of a fragment, so
"pmbootstrap kconfig check" can properly verify that all required kernel
options are there. Without this, it would fail an upcoming check for
BINFMT_ELF and BINFMT_SCRIPT:
https://lists.sr.ht/~postmarketos/pmbootstrap-devel/patches/38508
With the full config, pmbootstrap found that ANDROID_PARANOID_NETWORK
was enabled while it should be disabled, so disable it.
Fix the mediatek drvgen related build failure with
00_disable_drvgen.patch from linux-wiko-ufeel and including cust.dtsi:
https://wiki.postmarketos.org/wiki/Porting_to_a_new_device#Removing_python2_dependency
[ci:skip-build]: already built successfully in CI
6.1 was not a valid kernel version causing the wlan module installed
into wrong location. 6.1.0 would be correct. Fix that
problem by upgrading to 6.1.12 and make the wlan installation
more robust.
[ci:skip-build]: already built successfully in CI
Add a generic device that should work on x86_64 ChromeOS devices. This
is mostly a copy of tablet-x64uefi, with ChromeOS-specific stuff from
google-kevin. Keeps the UEFI parts so that it can still be booted with
alternative firmware (i.e. MrChromebox's RW_LEGACY builds). Lightly
tested on a Lenovo IdeaPad 3 Chromebook 11IGL05 (codename "Lick").
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
linux-postmarketos-mediatek-mt6735 6.1.9 added full display support and hardware acceleration
as well as haptics. Add a phoc configuration file to set the display scale, and a feedbackd
theme to optimize vibration durations. Route console output to UART to leave the splash
screen clean and to help with debugging when necessary.
[ci:skip-build] already built successfully in CI
If the wlan0 interface is rfkilled down on boot, WiFi won't work until reboot.
It seems that quickly ifconfig'ing wlan0 up and down in sysinit is enough to work around the bug.
[ci:skip-build] already built successfully in CI
Since re-crypt was finished now all T20/T30 devices
can be switched to use generic u-boot approach
and mount eMMC as external storage to host PC.
Unfortunately or fortunately this deprecates
any Android use on device. Have fun!
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Changes to defconfig:
* Disable legacy usb gadgets (USB_ETH and friends)
* Enable Multi-Gen LRU (LRU_GEN)
[ci:skip-build]: already built successfully in CI
Bring up support for Samsung T110 Goyawifi.
Working: Display (framebuffer), touchscreen, buttons and Wi-Fi.
Include: kernel source and necesarry firmware for Wi-Fi and Bluetooth.
samsung-goyawifi: fix patch names
samsung-goyawifi: remove mesa-dri-gallium
samsung-goyawifi: fix keyboard in deviceinfo
samsung-goyawifi: fix lightdm
samsung-goyawifi: editor-config ci tabs
samsung-goyawifi: add linux kernel as depends
[ci:skip-build]: Already built successfully in CI
Add the firmware for the CyberTan WC121.
Configuration is added in the newest firmware-linux release, so
complete support will appear in the corresponding Alpine package soon.
[ci:skip-build]: already built successfully in CI
Make use of stock depthcharge bootloader to not deal with U-Boot issues:
- broken USB
- broken eMMC
- broken latest version of U-Boot
Use extlinux instead of Grub for users with U-Boot to simplify process.
Also, some of old U-Boot builds may not support EFI.
[ci:skip-build] already built successfully in CI
Make use of stock depthcharge bootloader to not deal with U-Boot issues:
- broken USB
- broken eMMC
- broken latest version of U-Boot
Use extlinux instead of Grub for users with U-Boot to simplify process.
Also, some of old U-Boot builds may not support EFI.
[ci:skip-build] already built successfully in CI
New features:
* msm8994-huawei-angler: Add sdhc1 definition (internal SD card).
Backporting 3 patches:
* 0001-arm64-dts-msm8992-bullhead-add-memory-hole-region.patch
fixes bullhead boot since 6.0-rc1, already in qcom tree
* 0002-arm64-dts-qcom-msm8992-bullhead-Fix-cont_splash_mem-.patch
memory fix, likely to be merged
* 0003-arm64-dts-qcom-msm8992-bullhead-Disable-dfps_data_me.patch
memory fix, likely to be merged
* 0004-arm64-dts-qcom-msm8992-Don-t-use-sfpb-mutex.patch
memory fix, likely to be merged
* 0005-arm64-dts-msm8994-angler-fix-the-memory-map.patch
fixes angler reset during starting services in rootfs,
likely to be merged
Remove all backported commits from newer versions.
While at it, remove various CONFIG_NET_VENDOR_.* and
CONFIG_MSM_.* and CONFIG_.*_QCOM_.* for other SOCs.
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
[ci:skip-build]: already built successfully in CI
Shared SoC package for MSM8909
Currently provides a dummy soc-qcom-msm8909 package that depends on
soc-qcom-msm8916 and a soc-qcom-msm8909-modem package for modem support.
Since the RTC like on most Qualcomm chips is read-only, use
swclock-offset package to fix up time after boot.
And since we don't need msm-fb-refresher on mainline, move it to the
downstream kernel subpackage.
Basic support for the Kobo Libra H2O ebook reader.
Waveform handling shares the same oddities as for the Kobo Clara HD, the
existing waveform from eMMC is used.
Preferred way to install is to export the eMMC as USB Mass storage,
backing it up, and installing there.
U-Boot is a more recent one than the factory u-boot, supporting easy
access for buttons/LEDs. Pressing PageUp while powering on gives you the
possibility to enable USB mass storage mode to restore your backup.
Kernel is the near mainline kernel also used by the Kobo Clara HD.
It lacks some devicetree additions which are planned for the next
update, but basic things like buttons, usb, serial and wifi are
supported.
The WCNSS firwmare used for motorola-harpia seems to have weird issues
that prevent using WiFi properly except for a few limited channels. It
is not clear why this happens, it seems to be some peculiar firmware
difference (perhaps the channels need to be enabled with some
non-standard command).
Since Motorola uses the same signing keys for all their MSM8916
devices, it is possible to use the firmware from other devices instead.
Initial testing shows promising results when using the older WCNSS
firmware from motorola-osprey instead, it does not seem to have this
issue.
It's not clear yet if this has any negative effects. The WCNSS firmware
should not be device-specific, but theoretically it could be (if
Motorola made some weird changes inside it).
For now just package it in firmware-motorola-osprey-wcnss. This package
can be easily installed on harpia devices for testing (using apk add)
and will then take precendence over the default firmware from the
firmware partition (via msm-firmware-loader).
Move firmware-motorola-osprey from testing to community so that the
package is preserved for motorola-harpia users (testing is deleted in
stable branches).
[ci:skip-build]: already built successfully in CI
motorola-osprey can generally use the firmware from motorola-harpia
(which is a bit newer). However, the WCNSS_qcom_wlan_nv.bin is usually
device specific (it contains some kind of calibration values for
WiFi/BT).
The file packaged in firmware-motorola-osprey-wcnss-nv is identical to
the file in firmware-motorola-harpia-wcnss-nv. However, It looks a bit
like this might be a mistake in the source repository
(https://github.com/pmsourcedump/firmware-motorola-osprey). The
wlan/prima folder there is completely identical to the one used for
motorola-harpia, but the stock ROM and LineageOS use different files.
Fix this by packaging the file from TheMuppets. Also modernize the
firmware-motorola-osprey package by applying pil-squasher to the
venus/video firmware.
motorola-osprey has a very clunky name at the moment "Motorola Moto G
3rd gen. (2015)". The device was mostly just called "Motorola Moto G"
by Motorola, so it is hard to choose a fitting (but unique) name.
In the postmarketOS wiki it is called "Motorola Moto G 2015" so let's
just drop the "3rd gen." in the pmOS device package as well.
Also make the deviceinfo consistent with harpia while at it.
This adds initial support to CutiePi tablet, with basic peripherals, sound, touchscreen, and wireless support.
Signed-off-by: Raffaele Tranquillini <raffaele.tranquillini@gmail.com>
Add peripheral overlays
Signed-off-by: Raffaele Tranquillini <raffaele.tranquillini@gmail.com>
[ci:skip-build]: Already built successfully in CI
Use msm8916 kernel package instead of linux-postmarketos-qcom-msm8939
Also remove rmi_core from deviceinfo_modules_initfs
since it's automatically pulled by rmi_i2c
