The package `device-pine64-pinephone-vccq-mod` installs a u-boot user script.
The user script was loaded at address 0x50100000 partially overwriting
the initramfs (0x4FF00000-0x5015facd), and causing a boot loop.
The user script load address was increased to 0x50700000, leaving 8MB
of free space for the initramfs, the current initramfs size is 2.37MB.
Use -f, so rm
* does not complain if the file does not exist
* does not exit with 1 if the file does not exist
Remove the stdout/stderr redirect (not needed with -f).
Add exit 0 at the end of the file, even though it clearly should not
exit with anything other than 0 anymore, as it's common practice in
these pre-upgrade etc. scripts.
With the old script, the problem was that it would exit 1 as soon as the
files did not exist at the time the script runs. Exit 1 in this
pre-upgrade script causes apk to show an error, and it would not go away
with 'apk fix' since it ran into the same problem.
Fixes: 7c511d ("pine64-pinephone: remove old u-boot...")
On the pinephone, callaudiod handles the switching of default outputs,
so wys is unnecessary and may be causing issues when running in parallel
with callaudiod.
fixes#1217
with 5.14, there's some change to the path that alsa searches for ucm2
for this device. the install path for PinePhone.conf is changed, and it
references "full" path to HiFi and VoiceCall profiles (which I kept in
`PinePhone` dir, so that there could be several configs for the same
driver later on, if necessary/desired)
`$DEV` was an undefined variable so the atinout commands were printing their
helptext instead of actually running. This was noticeable because
the "Failed to enable VoLTE profile auto selecting" log was being printed
along with said helptext to syslog.
The block that defined `$DEV` had been accidentally deleted in
bb41f53879 . This change restores it.
[ci:ignore-count]
[ci:skip-vercheck] needed for the postmarketos-ui-* packages in this
series
[ci:skip-build] already built ui-* packages in CI, and device pacakges
are just trivial deviceinfo change (manually built some just to verify)
Headset jack events emit 2 events: 'Headset Microphone Jack'
and 'Headphone Jack'. These were properly detected before,
but not headphone jack events only: 'Headphone Jack'.
This change allows to detect headphone jack events as well
and act on these events by setting the headphones as
default audio output while keeping the internal
microphone as audio input. For headsets,
the microphone is switched to the headset microphone as well.
The PMIC AXP803 sends an interrupt to the A64 CPU when the
battery is critical low. This wakes up the phone at ~10%
battery level, but UPower wasn't configured to add upon
this interrupt as the action level was way lower.
Therefore, the PMIC performed a hard shutdown when the
battery level dropped further, which may cause data loss.
We used to have it at 40% and just bumped it to 100%. With 100%, I can
hear static noise in the headphones when using the PinePhone (pmOS CE)
in a silent room, even if I turn the volume down in Pulseaudio (e.g.
18%-30% in Phosh). This was not the case when we had it at 40%.
70% seems to be the sweet spot, where no static noise can be heard when
using headphones in a silent room, but where volume can still be turned
up to a very high level if necessary.
uboot-tools is provided by u-boot-tools but sometimes apk still gets
confused. This change prevents errors such as
pine64-pinephone:~$ sudo apk upgrade --verbose
WARNING: Failed to perform initial self-upgrade, continuing with full upgrade.
ERROR: unable to select packages:
uboot-tools (virtual):
provided by: u-boot-tools
required by: device-pine64-pinephone-0.25-r1[uboot-tools]
[ci:ignore-count]
[ci:skip-build]: already built in CI successfully
A hack shamelessly stolen from Manjaro. Plasma Mobile runs in the user
session and needs direct access to the sys entries of the flashlight to
be able to toggle it in the GUI
[skip ci] Broken, thinks there is an unreferenced file while there is
not
Move the shelli-specific alsa config from MR 1741 into a subpackage that
only gets installed together with shelli.
With the config installed, programs using alsa instead of pulseaudio,
can't be controlled through the volume setting in Phosh anymore (and
probably other UIs too). Shelli doesn't use pulseaudio.
Change the path of the config file like in MR 1877, so it's easier to
override it if necessary.
While at it, improve the APKBUILD slightly by fixing the install_if of
the phosh subpkg (should depend on =$pkgver-r$pkgrel, see APKBUILD
reference), and fix long lines.
This adds eg25-manager for managing modem power in userspace instead of
relying on the modem-power stuff in the kernel. The userspace
eg25-manager has proven to be more reliable than using modem-power.
An older setup-modem script is installed for ofono, since eg25-manager
cannot interface with ofono (yet).
The eg25 init script was removed since it only dealt with configuring
the modem-power driver in the kernel
[ci:skip-build]: already built successfully in CI
