- Also enabled LRU_GEN by default like on the PinePhone OG
- Set Ext4 module to built-in as this currently is the main fs used for PPP.
Contains the following patch:
- pinephone pro: finished fix for LCD to make it refresh at precisely 60 Hz
[ci:skip-build]: already built successfully in CI
Add new patches:
- enable serial console
- save relocation address to find KASLR
- buttons as keyboard input driver to navigate bootmenu
- bootmenu loop entry selection
Apparently upstream names udev rules with the .udev extension... which
doesn't work with udev (I guess debian has a helper for installing rules
and it renames them?). This adds the expected ".rules" extension to them
so that udev actually uses them.
This update also includes improved ucm config from Purism.
"Lockdown suppport" is also added here, which allows toggling off all of
the hks on the L5 to disable all radios, etc without breaking some
sensors. For more info, see 65ec7038 in librem5-base.
Based on some new (to me...) info from Purism's Sebastian K, there are
apparently Evergreen devices that return different values for board rev,
so we shouldn't assume only r4 are Evergreen, and default to the r2 DT.
But many earlier devices (Birch, Chestnut, Dogwood) may or may not have
the board rev set either. Who knows! Defaulting to the Evergreen DT on
these devices is bad too, but there weren't many of those shipped (I
guess?), at least not compared to the number of Evergreens that aren't
properly identifiable in u-boot... so this using this DT by default is
the best of the two bad options we have.
This comment thread has more info:
https://gitlab.com/postmarketOS/pmaports/-/issues/1643#note_1147248594fixes#1643
[ci:skip-build] already built successfully in CI
Add the CONFIG_DW9714 symbol to the PinephonePro defconfig.
The PinephonePro rear camera module uses the DW9714 VCM to drive the
lens, and a driver is required to successfully complete the media
graph probe sequence.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Kernel source updated to 6.1-rc7
Ext2 and Ext3 modules in aarch64 config disabled because Ext4 is backwards compatible.
2 fixes for PinePhone included in this source:
pinephone: fix power key behavior during suspend (avoid stuck key during resume)
pinephone keyboard: wait for 100ms after enabling power supply and before probing.
[ci:skip-build]: already built successfully in CI
In SDM845, the q6voice kernel driver connects modem and audio backends.
Callaudiod seems to switch to correct audio device and prepares it, however, the audio
device get's closed since no one from the userspace is actively listening to it.
This cuts the audio in call. As a workaround, I have added to script to disable the
suspend-on-idle pulseaudio module during calls, so the audio devices don't close automatically.
Includes the following changes:
- rebase onto rc4
- squash a few changes which were marked to get squashed/fixups
- dropped "wcd934x: use .prepare and .shutdown instead of .trigger"
- OP6 audio device tree changes
- revert of a DSI DCS commit[1], which caused havoc in unprepare
hooks of panel drivers
[1] - https://lore.kernel.org/linux-arm-msm/1892d0af-8aa4-dc03-887a-e44bb623b836@linaro.org/
Change-Id: I4790a278c0d35618ca824a036982769e66767ffd
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
Downstream for kernel development, not for actual use.
Kernel defconfig taken from stock with:
- CONFIG_ANDROID_PARANOID_NETWORK unset
- CONFIG_DEVTMPFS set
- CONFIG_EXT4_FS_POSIX_ACL set
- CONFIG_LOCALVERSION set to "-downstream"
- CONFIG_SYSVIPC set
- CONFIG_USB_CONFIGFS_RNDIS set
- CONFIG_USER_NS set
Change-Id: I22bfd30dfc664dfaa2123c856b3662ddb37e760f
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
[ci:skip-build]: already built successfully in CI
Enable vulkan on supported hardware configurations
out of the box.
Change-Id: I6c8e1713e7c834aae3a162b8a681f5abde02ed5e
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
Since 00648d0282dcca1da453c0b20d27e24bf901a854, the correct serial console name
is ttySx instead of the older ttyOx. Reflect this in cmdline passed to kernel
via u-boot
[ci:skip-build]: already built successfully in CI
The file brcmfmac43455-sdio.raspberrypi,4-model-b.bin is now provided by
linux-firmware-brcm package in Alpine. Remove to symlink to stop the
file conflict.
I renamed the repository so GitHub changed all the checksums. :(
[ci:skip-vercheck]: the source files are still exactly the same
[ci:skip-build]: Already built successfully in CI
Support launching postmarketOS in QEMU on riscv64 architecture. It is
mostly copied from device-qemu-aarch64 with some riscv64-specific
modifications.
Currently UIs using Xorg like Mate, XFCE4 and LXQT work fine, Wayland
UIs like weston, plasma-mobile etc didn't work in my testing.
Also using "pmbootstrap qemu --tablet" is needed to make mouse input
work, the defaults don't seem to work at the moment.
[ci:skip-build]: already built successfully in CI
Now that touchscreen driver is supported in kernel, include the module
in initfs so it's available there.
[ci:skip-build]: Already built successfully in CI
Remove mainline postfix in initramfs module list,
because sagit has only 1 kernel for now.
Blacklisting ipa module fixes poweroff.
See 68cdc1ea2b commit for more info.
[ci:skip-build]: already built successfully in CI
This is an early mainline port for the MediaTek MT6763 Helio P23 SoC
that just about boots in about 3 minutes with one core online, logs on
display (simplefb) or UART serial console and USB gadget mode
facilitating netbooting postmarketOS while tethered via RNDIS.
This contains a fix for second panel variant for samsung-hlte.
No more manual changes, .config was regenerated using kconfig migrate.
[ci:skip-build]: already built successfully in CI
This is an incomplete port but it has greater functionality than the existing downstream based one, which has been moved to unmaintained.
[ci:skip-build]: Already built successfully in CI
There are 2 panel variants supported:
- panel-samsung-hx8389c-gh9607501a
- panel-samsung-s6d78a0-gh9607501a
Add both of them to enable panel display during splash and FDE.
Note that fortunaltezt has only one panel variant so it's not included.
[ci:skip-build] already built successfully in CI
Device uses mainline kernel. What works:
- boots
- display
- touchscreen
- wifi
Also add firmware package
[ci:skip-build]: already built successfully in CI
New features for google-sargo:
- GPU acceleration
- Bluetooth
- Haptics (currently only rumble effect)
- Video acceleration (still untested)
- NFC (only detection was tested)
Certain newer hardware may require a newer kernel than the current
lts in order to work.
Change-Id: Iae0d91f8bf8d1b8516698841895f942e527b0813
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
[ci:skip-build]: already built successfully in CI
Remove the -dev subpackages of kernels that replace the linux-headers
package. As I understand, the only case where this would make sense is
if you wanted to build a kernel module against headers that need to be
newer than the headers in Alpine's linux-headers package (currently
5.19.5).
While this might have been historically relevant when wireguard wasn't
in the kernel and you might have needed newer linux-headers to build
the module, it seems irrelevant today. If somebody should need this in
the future, then bring it back properly / consider getting the
linux-headers package in Alpine upgraded. Right now the -dev packages
are broken in several ways:
* Use of unversioned provides= (pma#1766)
* Don't contain binaries needed to build binary packages (pma#462).
This was worked around in 6aba5f ("Package kernel-scripts
separately"), but later this didn't build anymore and we removed it.
So in short: broken and unused, drop them.
Change-Id: Ice7c2942892eb0a173dcded835d5fac5a8f32066
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
[ci:skip-build]: already built successfully in CI
Update the ALSA UCM package for the SDM845 so the ALSA UCM configs for
the SHIFT6mq are included. Speaker, microphones, headset work fine in
HiFi mode. In Voice Call mode, the microphone works, but the earpiece is
still silent.
[ci:skip-build]: already built successfully in CI
q6voiced is a daemon to allow voice calls with the q6voice kernel
driver. Add its config so it can open the right audio device on the
SHIFT6mq during a call.
Explicitly set Fn key as Mod5. In xkeyboard-config up to 2.36, this was somehow
set implicitly, since it was working, although I am not sure where/how. In 2.37
it only works when specified.
[ci:skip-build]: already built successfully in CI
Since N900 rtc works fine, remove swclock from boot as it causes time to be set
wrong. Additionally, rtc device is set correctly in kernel, so remove old,
adjusted hwclock config.
Partially reverts pmaports 0e502a5139
[ci:skip-build]: already built successfully in CI
Venji10 is no longer involved in actively maintaining the package for more than a year plus.
Changing myself to be the maintainer and also updated my email id.
[ci:skip-build]: already built successfully in CI
Because of recent changes to kernel and alsa-ucm-conf,
the q6voiced device is changed.
Venji10 is no longer involved in actively maintaining the package for more than a year plus.
Changing myself to be the maintainer and also updated my email id.
Rebased our work on top of latest upstram alsa-ucm-conf.
The beryllium ucm conf is also reworked to fix wrong default audio device issue
and now headphones auto-switching on plugin also works as expected.
Adding myself as a co-maintainer for this package.
Change-Id: I360c60d1675c884c9e85cd95f940fa6cb4b75e83
Signed-off-by: Joel Selvaraj <joelselvaraj.oss@gmail.com>
Change-Id: I986b3401fd81ac18b7336f8f0be53e2cf4c4515c
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
Signed-off-by: Joel Selvaraj <joelselvaraj.oss@gmail.com>
After c49180f8cf, usbnet did not come up on N900
automatically since the UDC probed a little late. Fix this by making the driver
built-in.
While at it, make watchdog built-in so it can be kicked even when boot takes
long for any reason.
[ci:skip-build]: already built successfully in CI
These are the patches added to mitigate the CVE's which have been found in wifi stack.
More information on these CVE's can be found over here: https://seclists.org/oss-sec/2022/q4/20
[ci:skip-build]: Already built successfully in CI
- Downgrade kernel from EOL 5.18 to LTS 5.15 in order to apply WiFi CVE fixes.
It is currently not possible to upgrade to newer (5.19+) kernels due to a USB
regression.
- Modify 0005-iio-accel-st-accel-add-lis302dl.patch so it applies on 5.15.74
- Reinstate 0008-wl1251-specify-max.-IE-length.patch for nl80211 support. Patch
was dropped because it is in mainline since 5.18
[ci:skip-vercheck]: downgrade
[ci:skip-build]: already built successfully in CI
For a merge list, please see the merge commits:
- 5.19.13 - (6384fddb50)
- 5.19.14 - (85caddc9c8)
- 5.19.15 - (fca27cdc51)
- 5.19.16 - (9aa25bf492)
Note: This is an important release, as 5.19.16 fixes the recently
published wifi stack vulnerabilities.
Change-Id: Iffff2c65bdd697b01bc5d8fc090e9a2f2577c701
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
This updates the APKBUILD with the new Megi 6.0.2 tag release.
The 2 incremental patches on top of 6.0 have hereby been removed.
[ci:skip-build]: already built successfully in CI
RootFS cannot be flashed on this devices since Samsung uses a different sparse format.
Enable this in the deviceinfo file to allow flashing the rootFS.
[ci:skip-build]: already built successfully in CI
This kernel upgrade comprises of 2 point releases 6.0.1 and 6.0.2.
the release from 6.0 to 6.0.2 is a regular maintenance release.
Kernel update 6.0.2 addresses 5 important CVE's in the Wifi stack.
More info can be found over here: https://seclists.org/oss-sec/2022/q4/20
[ci:skip-build]: already built successfully in CI
This kernel update addresses 5 important CVE's in the Wifi stack.
More info can be found over here: https://seclists.org/oss-sec/2022/q4/20
[ci:skip-build]: already built successfully in CI
- Update to Linux v6.0.2 (includes fixes for WiFi CVEs)
- Tweak kernel configuration slightly (especially crypto options)
[ci:skip-build] Already built successfuly on CI in MR
- Update to Linux v6.0.1
- Upstreamed some patches this time
- Fixed register address in smb1360 driver
Device changes:
- samsung-gtelwifiue
- Audio
- Better USB detection
- samsung-e5/e7/grandmax
- Refactoring for changes that landed upstream
- Key LED control
New devices:
- samsung-cprime/heatqlte
- eMMC, SD card, USB, Buttons, WiFi/BT, Vibrator
- Display, Brightness control (not for AMOLED on heatqlte)
- Sensors (Accelerometer)
- Sound/Modem
- Battery status
- NFC
- NOTE: No touchscreen yet
Our patch needs to be adjusted after commit 58e4a2d27d32 ("extcon: Fix
extcon_get_extcon_dev() error handling"). Also generate all other
patch headers, and make it possible to apply patch 0008 and 0009 with
git am.
Additionally switch mainline kernel from qcom_fg to bq27xxx_battery_i2c.
While at it simplify the deviceinfo_modules_initfs_alpine list to
exclude implicit dependencies that mkinitfs can find itself to make the
line length a bit less unwieldy.
[ci:skip-build] Already built successfuly on CI in MR
Additionally switch mainline kernel from qcom_fg to bq27xxx_battery_i2c
and probe the correct panel driver, this was a regression that came from
the initial linux-edge enablement MR.
While at it simplify the deviceinfo_modules_initfs_alpine list to
exclude implicit dependencies that mkinitfs can find itself to make the
line length a bit less unwieldy.
While this provides the ability to use ModemManager, there are quite a
lot of issues with the driver still; keep it enabled in kernel for now
and let users "modprobe ipa" if they want to test modem features
whichever side effects that may cause including:
- Making the device nearly impossible to poweroff or reboot
- Making the UI lag noticeably more due to some interconnect bandwidth
issues
While this provides the ability to use ModemManager, there are quite a
lot of issues with the driver still; keep it enabled in kernel for now
and let users "modprobe ipa" if they want to test modem features
whichever side effects that may cause including:
- Making the device nearly impossible to poweroff or reboot
- Making the UI lag noticeably more due to some interconnect bandwidth
issues
The qca (Bluetooth) and qcom (non-zap GPU) firmware blobs don't need to
be signed by the OEM, so let's use upstream versions to benefit from
fixes and updates done there.
The soc-qcom-sdm845* packages are mostly sufficient, but there are a few
issues that all MSM8998 devices on mainline will face, so include
workarounds for them in a generic package all device pkgs can depend on.
