There are 2 panel variants supported:
- panel-samsung-hx8389c-gh9607501a
- panel-samsung-s6d78a0-gh9607501a
Add both of them to enable panel display during splash and FDE.
Note that fortunaltezt has only one panel variant so it's not included.
[ci:skip-build] already built successfully in CI
Fixes:
- Fix installation with FDE
- Use new path to kpartx (MR 16)
Other:
- pmos_install: Increase boot partition size to 256MB (MR 14)
- pmos_install_functions: make shellcheck happy
- update-binary: make shellcheck happy
[ci:skip-build] already built successfully in CI
Device uses mainline kernel. What works:
- boots
- display
- touchscreen
- wifi
Also add firmware package
[ci:skip-build]: already built successfully in CI
There is "iifname "wwan*" drop" defined in 01_wwan.nft, which drops
any not "established, related" incoming packet from WWAN.
[ci:skip-build]: already built successfully in CI
New features for google-sargo:
- GPU acceleration
- Bluetooth
- Haptics (currently only rumble effect)
- Video acceleration (still untested)
- NFC (only detection was tested)
Certain newer hardware may require a newer kernel than the current
lts in order to work.
Change-Id: Iae0d91f8bf8d1b8516698841895f942e527b0813
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
[ci:skip-build]: already built successfully in CI
With recent cross/gcc-* upgrades, we actually require pmbootstrap
1.47.0 to avoid the following error:
ERROR: Invalid pkgver '${_pkgbase}_git${_pkgsnap}' in APKBUILD: /home/user/.local/var/pmbootstrap/cache_git/pmaports/cross/gcc-aarch64/APKBUILD
The pkgver is significantly lower (0.19) than the one of megapixels
(1.5.2 as of writing), so we can use the versioned provides here. If it
was closer so megapixels-purism's pkgver could become higher than
megapixels in the future, then we should use unversioned provides with
provider priorities instead.
Drop replaces, provides for postmarketos-config-firefox. This was the
name of the package until August of 2020, not relevant anymore. Also
the provides didn't have pkgrel and therefore was wrong.
Remove the -dev subpackages of kernels that replace the linux-headers
package. As I understand, the only case where this would make sense is
if you wanted to build a kernel module against headers that need to be
newer than the headers in Alpine's linux-headers package (currently
5.19.5).
While this might have been historically relevant when wireguard wasn't
in the kernel and you might have needed newer linux-headers to build
the module, it seems irrelevant today. If somebody should need this in
the future, then bring it back properly / consider getting the
linux-headers package in Alpine upgraded. Right now the -dev packages
are broken in several ways:
* Use of unversioned provides= (pma#1766)
* Don't contain binaries needed to build binary packages (pma#462).
This was worked around in 6aba5f ("Package kernel-scripts
separately"), but later this didn't build anymore and we removed it.
So in short: broken and unused, drop them.
apk treats provider_priority=0 as if it is not there, not as lowest
value. The previous patch set it to =10 for …-sxmo-de-sway, so set it to
=5 for the dwm version.
Related: c21f61ddd8/src/solver.c (L713-721)
apk ignores a provider_priority of 0. In order to have …-sxmo-de-dwm
have a lower provider priority than …-sxmo-de-sway, set a higher
priority than 1 for the sway version.
Change-Id: Ice7c2942892eb0a173dcded835d5fac5a8f32066
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
[ci:skip-build]: already built successfully in CI
For some reason, alsa sometimes probes it from another locations.
Add symlinks to handle it
Tested-by: Eric Curtin <ecurtin@redhat.com>
[ci:skip-build]: already built successfully in CI
Update the ALSA UCM package for the SDM845 so the ALSA UCM configs for
the SHIFT6mq are included. Speaker, microphones, headset work fine in
HiFi mode. In Voice Call mode, the microphone works, but the earpiece is
still silent.
[ci:skip-build]: already built successfully in CI
q6voiced is a daemon to allow voice calls with the q6voice kernel
driver. Add its config so it can open the right audio device on the
SHIFT6mq during a call.
