Add the required dependencies and config for both hexagonrpcd and
libssc so that sensors start working.
[ci:skip-build]: already built successfully in CI
Add the required dependencies and config for both hexagonrpcd and
libssc so that sensors start working.
[ci:skip-build]: already built successfully in CI
The device already loads plenty of nonfree-firmware into the
co-processors during the bootloader stages, and also once booted in
Linux won't really be useful without everything.
Additionally I doubt anyone tests that case, so just require nonfree
firmware unconditionally to simplify maintenance.
This gets Bluetooth working for the Sparklan card.
btattach doesn't work on the Librem5 at the moment (see [1]) so even
though it's deprecated let's use hciattach to get things working.
1: https://source.puri.sm/Librem5/librem5-base/-/issues/76
Signed-off-by: Alistair Francis <alistair@alistair23.me>
[ci:skip-build] already built successfully in CI
I made an oversight in pmaports!5295 which caused the post-install
script to try enabling the sd8x-wlan service even if the downstream
subpackage isn't installed. This causes errors when creating a new
mainline rootfs, so fix it by moving the install variable declaration to
the subpackage function.
Patches were rebased, sadly nothing was dropped :(
All kconfig changes are from simply running `kconfig migrate` and
accepting all defaults when prompted
[ci:skip-build]: already built successfully in CI
Resolves this harmless, but annoying error on mainline:
* Enabling wlan driver ...
/lib/rc/sh/openrc-run.sh: line 14: can't create /sys/devices/platform/sd8x-rfkill/pwr_ctrl: nonexistent directory
* ERROR: sd8x-wlan failed to start
[ci:skip-build]: already built successfully in CI
This also increases the (necessarily) hardcoded initrd end by 16MiB in
the DTS, which is necessary to make the phone boot with the new
initramfs (and in general any initramfs which exceeds 2624KiB).
This seems to be some Samsung's proprietary verified boot solution.
After a recent update, this started bootlooping my phone.
I have no idea why it only fired now, but pmOS does not use this
feature anyway, so it won't hurt to disable it.
[ci:skip-build] Already built fine once
Without it some devices will fail to mount the boot partition:
FAT-fs (mmcblk1p1): IO charset ascii not found
Also disable CONFIG_RT_GROUP_SCHED.
Reported-by: Anton Bambura <jenneron@protonmail.com>
Signed-off-by: Ferass El Hafidi <funderscore@postmarketos.org>
[ci:skip-build]: already built successfully in CI
This cmdline argument is now a no-op. Drop it everywhere and add a new
CI check to enforce this.
Adjust the deprecated "minimal" initramfs variant to use
pmos.debug-shell to enable logging instead. It doesn't /support/
dropping to a shell, so the variable takes on a different meaning. But
that's ok since it's at least more consistent.
[ci:ignore-count]
[ci:skip-vercheck]
Signed-off-by: Caleb Connolly <caleb@postmarketos.org>
Tweaked-by: Oliver Smith <ollieparanoid@postmarketos.org>
[ci:skip-build]: kernel builds are very likely to go through now
* drop maxcpus=0, which was added with 73a033328e ("device-nokia-n900: set
uniprocessor mode for kernel (MR 4299)") while troubleshooting. a better
fix was eventually implemented with 3e737241ba ("linux-postmarketos-omap:
N900: disable twl off idle features (MR 4317)")
* drop PMOS_NO_OUTPUT_REDIRECT, which was obsoleted by 7c98127746
("postmarketos-initramfs: switch to udev and kmod (MR 5000)")
