New mainline port with most things working (usb/wifi/bt/3d-accel/sound/gps).
Modem/calls/sms/mobile-data should work but couldn't test it recently
due to broken devices.
These are required to make it work with the latest ModemManager patches,
especially the patch that switches BAM-DMUX to Raw-IP mode.
[ci:skip-build]: already built successfully in CI
- Update to Linux 5.11.7
- Upstreamed more patches
- Switch BAM DMUX (mobile data) driver to Raw-IP mode.
This makes it work with the upstream version of ModemManager,
reduces overhead a bit and is overall cleaner.
- Add QMI "memshare" driver which is needed for GPS to work on most
MSM8916 devices.
- GPS has been tested successfully on:
- alcatel-idol347
- lg-m216
- longcheer-l8150 (wileyfox-crackling)
- longcheer-l8910 (bq-paella)
- motorola-harpia
- motorola-osprey
- samsung-a2015 (a3(u)lte, a5(u)lte)
- samsung-serranovelte
- wingtech-wt88047 (xiaomi-wt88047)
- Needs more testing/investigation on:
- asus-z00l
- asus-z010d
- wingtech-wt865x8
- Add SMB1360 battery/charger/OTG driver for longcheer-l8190
and wingtech-wt88047.
- Rework TFA9895 speaker amplifier driver for potential upstreaming,
make it work for TFA9897, add channel selection and a lot of cleanup.
- Add INSTALL_MOD_STRIP=1 to maybe reduce the size of modules a bit.
- Other things I forgot :)
Device changes:
- alcatel-alto5-vdf: Initial support for Vodafone Smart prime 6
- USB
- Storage (eMMC, SD card)
- Buttons
- WiFi, Bluetooth
- alcatel-idol347: Initial support for Alcatel Idol 3 (4.7")
- USB
- Storage (eMMC, SD card)
- Display, Brightness
- Touchscreen, Buttons, Vibrator
- WiFi, Bluetooth
- Accelerometer, Magnetometer, Gyroscope, Proximity
- Audio (no headphones yet)
- Modem (voice call audio needs some more minor changes)
- asus-z00l
- SD card
- IMU (Accelerometer + Gyroscope), Magnetometer
- lg-m216
- Battery/charging
- longcheer-l8150 (wileyfox-crackling)
- Tweak battery values slightly for 25°C instead of 0°C
- longcheer-l8910 (bq-paella)
- Battery/charging
- USB OTG
- motorola-harpia
- Add panel driver for "boe" panel
- samsung-gt510wifi/matissevewifi:
- Fix touchscreen
- wingtech-wt88047 (xiaomi-wt88047)
- Battery/charging
- USB OTG
[ci:skip-build]: already built successfully in CI
(Also sync with Alpine while I'm at it...)
This is necessary for mobile data to work on MSM8916-based devices
after some changes in the network driver (bam-dmux) to operate in
Raw-IP mode instead of Ethernet mode (which is somewhat broken).
* Add u-boot build with a lot of patches that makes the display work in
u-boot for boot selection
* Upgrade the rockchip kernel to 5.11 mainline with config for the
rk3399 devices built-in
* Make the rockpro64 and pinebook pro use the newer kernel
[ci:skip-build]
Actually the display in asus-me176c has a width of 800px, which means
that the splash screen isn't perfectly centered. Correct this in
deviceinfo to make it show up correctly.
Also, add configuration file for Phosh to reduce scaling a bit to 1.75.
It's kind of subjective but scaling = 2 definitely feels too large.
[ci:skip-build]: already built successfully in CI
This is 3.24.27 w/ Purism's mobile UI patches in their fork. According
to Purism, 3.24.27 resolves some stability issues (like a segfault when
scrolling)
[ci:skip-build]: already built successfully in CI
There's a race condition between when the pwmled device is initialized,
which kicks off a feedbackd udev rule that configures the led trigger to
'pattern', and when ledtrig_pattern actually loads. It seems to mostly
load after the rule runs, so the trigger is never set to 'pattern' on
boot.
This removes the race by building the ledtrig_pattern driver into the
kernel.
[ci:skip-build] Already build successfully in CI
This patch fixes a fairly severe performance regression with wifi on the
L5 (something like 20x improvement in performance with this patch)
[ci:skip-build] Already build successfully in CI
In order to have hardware acceleration in osk-sdl, we have included mesa
for some devices (like the PinePhone) in initfs-extra. Mesa drags in
libLLVM, which got a size increase of 27 MB in the last version. This
leads to running out of space on the boot partition:
==> initramfs: creating /boot/initramfs-postmarketos-allwinner-extra
gzip: write error: No space left on device
cpio: write error: Broken pipe
Improve the situation by not directly writing initfs-extra to /boot
(next to the old version), but to a temporary directory first. Replace
the old version with the new version afterwards (like before).
This is a rather minimal fix for this specific issue. The mkinitfs
script needs more fixing (it's one of the oldest pieces of code in
postmarketOS and could use a rewrite...), but that's out of scope for
this patch.
The device has been renamed from fujitsu-m532 to pegatron-chagall since several rebrands of this board exist (Olivetti Olipad3, Siragon 4N, etc.), and Fujitsu M532 is just one of those.
Signed-off-by: Raffaele Tranquillini <raffaele.tranquillini@gmail.com>
Ship mode via the mechanism used by purism doesn't work; it's either not
possible or outside my understanding to run an openrc runscript with a
busybox init on *poweroff* and *not reboot*, which is what is required
for this to work properly..
This module param requires a corresponding kernel patch to enable ship
mode support in the bq25890-charger module
Upstream change logs:
5.11.2:
fdc91c4e20
5.11.4:
a178aa515c
This also adds a -dev subpackage, and cleans up makedepends
[ci:skip-build]: already built successfully in CI
This does not work as expected, CI doesn't run for x86 and armhf on
master too. An attempt to fix this was made in MR 2030, but it didn't
work as expected and it's not worth looking into this further right now.
This reverts commit d695455f08.
Changes from purism:
- 2 second boot delay removed
- This includes an updated DDR memory training firmware version.
- patch to work around wifi device not being available on boot
Package changes:
- u-boot installed in location consistent with other pmaports/u-boot
packages
- update-u-boot script added for upgrading u-boot on the device
- devkit u-boot split off into a sep. subpackage
This disables ccache in the CI when building packages. I think ccache is
not necessary since the CI will never build a package twice in the same
pipeline, and ccache dir is not preserved for use between pipelines.
There is a real time cost to compiling with ccache enabled on the
initial compile (compressing objects for cache, etc), and some testing
with building the linux-purism-librem5 kernel in the CI shows this cost
can be significant... ~160 minutes when ccache is enabled vs ~105
minutes when it is disabled with this patch.
kernel compile CI runs referenced:
https://gitlab.com/postmarketOS/pmaports/-/jobs/1087602863https://gitlab.com/postmarketOS/pmaports/-/jobs/1087956999
Some testing on my laptop using osk-sdl with and without ccache for
initial compile:
ccache disabled:
$ rm _build -r && CCACHE_DISABLE=1 meson _build >/dev/null && CCACHE_DISABLE=1 time meson compile -C _build
ninja: Entering directory `_build'
[10/10] Linking target osk-sdl
7.76
$ rm _build -r && CCACHE_DISABLE=1 meson _build >/dev/null && CCACHE_DISABLE=1 time meson compile -C _build
ninja: Entering directory `_build'
[10/10] Linking target osk-sdl
7.89
$ rm _build -r && CCACHE_DISABLE=1 meson _build >/dev/null && CCACHE_DISABLE=1 time meson compile -C _build
ninja: Entering directory `_build'
[10/10] Linking target osk-sdl
7.71
ccache enabled:
$ rm /tmp/ccache _build -r && CCACHE_DIR=/tmp/ccache meson _build >/dev/null&& CCACHE_DIR=/tmp/ccache time meson compile -C _build
ninja: Entering directory `_build'
[10/10] Linking target osk-sdl
8.62
$ rm /tmp/ccache _build -r && CCACHE_DIR=/tmp/ccache meson _build >/dev/null&& CCACHE_DIR=/tmp/ccache time meson compile -C _build
ninja: Entering directory `_build'
[10/10] Linking target osk-sdl
8.46
$ rm /tmp/ccache _build -r && CCACHE_DIR=/tmp/ccache meson _build >/dev/null&& CCACHE_DIR=/tmp/ccache time meson compile -C _build
ninja: Entering directory `_build'
[10/10] Linking target osk-sdl
8.54
