I made an oversight in pmaports!5295 which caused the post-install
script to try enabling the sd8x-wlan service even if the downstream
subpackage isn't installed. This causes errors when creating a new
mainline rootfs, so fix it by moving the install variable declaration to
the subpackage function.
Patches were rebased, sadly nothing was dropped :(
All kconfig changes are from simply running `kconfig migrate` and
accepting all defaults when prompted
[ci:skip-build]: already built successfully in CI
Resolves this harmless, but annoying error on mainline:
* Enabling wlan driver ...
/lib/rc/sh/openrc-run.sh: line 14: can't create /sys/devices/platform/sd8x-rfkill/pwr_ctrl: nonexistent directory
* ERROR: sd8x-wlan failed to start
[ci:skip-build]: already built successfully in CI
This also increases the (necessarily) hardcoded initrd end by 16MiB in
the DTS, which is necessary to make the phone boot with the new
initramfs (and in general any initramfs which exceeds 2624KiB).
This seems to be some Samsung's proprietary verified boot solution.
After a recent update, this started bootlooping my phone.
I have no idea why it only fired now, but pmOS does not use this
feature anyway, so it won't hurt to disable it.
[ci:skip-build] Already built fine once
Without it some devices will fail to mount the boot partition:
FAT-fs (mmcblk1p1): IO charset ascii not found
Also disable CONFIG_RT_GROUP_SCHED.
Reported-by: Anton Bambura <jenneron@protonmail.com>
Signed-off-by: Ferass El Hafidi <funderscore@postmarketos.org>
[ci:skip-build]: already built successfully in CI
This cmdline argument is now a no-op. Drop it everywhere and add a new
CI check to enforce this.
Adjust the deprecated "minimal" initramfs variant to use
pmos.debug-shell to enable logging instead. It doesn't /support/
dropping to a shell, so the variable takes on a different meaning. But
that's ok since it's at least more consistent.
[ci:ignore-count]
[ci:skip-vercheck]
Signed-off-by: Caleb Connolly <caleb@postmarketos.org>
Tweaked-by: Oliver Smith <ollieparanoid@postmarketos.org>
[ci:skip-build]: kernel builds are very likely to go through now
Use stock WiFi firmware instead of the generic linux-firmware-brcm
firmware. The stock firmware is newer and seems to be better suited
for the BCM4334B2 variant used in these tablets.
This fixes timeout errors from the brcmfmac driver and seems to
slightly improve download/upload speeds (by about 1MB/s).
trailblazer is a bleeding edge, unstable target for EFI capable ARM64
devices. It runs linux-next and should otherwise be adjusted to support
as many devices as possible.
The goal of trailblazer is to motivate more upstream kernel development by
providing a tighter feedback loop (patches land in -next weeks before they
make it into mainline or stable), as well as encouraging more generic
solutions to the device specific hacks we have in userspace.
On supported devices, trailblazer should reflect the current state of
upstream. It allows users to easily appreciate what feature are
unavailable, and more importantly appreciate when a new feature does get
added upstream.
Due to the instability of linux-next, the plan is to have BPO build
trailblazer images nightly, so if next breaks then the images should
only be broken for a day.
Signed-off-by: Caleb Connolly <caleb@postmarketos.org>
Introduce a linux-next kernel with postmarketOS configs and some
additional device specific configs enabled.
This kernel package will be updated daily to the latest -next tag.
breakages expected. It is designed to be used in tandem with a generic
ARM64 device package to provide a bleeding edge option for those with
EFI capable bootloaders.
Signed-off-by: Caleb Connolly <caleb@postmarketos.org>
Depend on msm-firmware-loader, firmware- and soc- packages.
Sort deps alphabetically.
Tidy up deviceinfo:
* add flash_kernel_on_update
* remove unneded things from kernel cmdline
[ci:skip-build]: already built successfully in CI
Currently it requries the check_code result check in the
vendor uboot to be disabled as explained in the wiki.
Booting directly via reconfigured boot order still
does not work. It hangs somewhere in the kernel.
Firmware for Wifi/BT is not included yet.
It could use the linux-postmarketos-omap kernel in the future,
but there are still some dirty things in there e.g. for sound
which are not suitable for a multi-device kernel.
[ci:skip-build]: already built successfully in CI
PineTab 2 is a successor to the original PineTab from PINE64 released
in mid-2023.
The tablet came with DanctNIX's fork of Arch Linux ARM, comes with
K Desktop Environment as the UI and available with 64GB eMMC/4GB RAM
or 128GB eMMC/8GB RAM.
Changelog since 6.7:
General:
* Adreno 5xx preemtion is now disabled due to hangs it causes.
This makes GPU a lot more cooperative on these platforms.
* Fixed absence of zap-shader region which caused devices with
GPU enabled to freeze the whole system.
* Fixed ath10k Wi-Fi not connecting to 5Ghz networks.
* Incorporated in-kernel pd-mapper patchset, therefore userspace
pd-mapper daemon is not required.
* Kernel cmdline from bootloader is no longer ignored completely,
in other words, not hardcoded. You can now modify cmdline in
deviceinfo file and changes in that file will not be ignored.
Devices:
* Xiaomi Redmi Note 7 (lavender):
* split device trees into 2 variants by panel type (Tianma & BOE)
* GPU + panel support for 2 variants
* Vibrator support
* Connectivity: modem, Wi-Fi and bluetooth support.
* Other/all devices:
* update device trees according to upstream USB stack changes
(related to USB 3 phy support)
Install script into /etc/profile.d with workaround for mesa bugs.
This makes most SDM660 devices usable for general people out of the box.
Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Add msm-firmware-loader, soc-qcom-sdm660-rproc, firmware-xiaomi-lavender
and firmware-qcom-adreno-a530 as dependency. This is necessary to make
Wi-Fi and modem work.
Add support for panel drivers.
Phoc now defaults to 1,25 as scale on skomer, which while not perfect,
is good enough and lets the device be unlocked. As such, let's remove
this configuration file and encourage improvements upstream instead.
See https://gitlab.com/postmarketOS/pmaports/-/merge_requests/4541
For now, limited support without graphics. Graphics
support would need messing and detecting board variants.
especially since Rev B seems to need a vcom setting per batch.
[ci:skip-build]: already built successfully in CI
Add support for the Xiaomi Miatoll phones. There are currently two
device trees in the upstream kernel.
Signed-off-by: David Wronek <david@mainlining.org>
The original maintainer unfortunately has bricked their phone. Drop the
device package in preparation for the SM7125 kernel upgrade.
Signed-off-by: David Wronek <david@mainlining.org>
The device trees for this phone have never been upstreamed
unfortunately. Drop the device package in preparation for the SM7125
kernel upgrade.
Signed-off-by: David Wronek <david@mainlining.org>
He did an awesome job adding an initial port for this device but hasn't
helped to maintain it, so I'm removing him from the list of active maintainers.
This causes a lot of spam in dmesg about "failed to allocate compressor transform", making it nearly impossible to search anything in the system logs.
This option has nothing to do with zram.
[ci:skip-build]: already built successfully in CI
- Enable KVM support (for using with slbounce!)
- Disable RT_GROUP_SCHED, community device kernel requirement
[ci:skip-build]: already built successfully in CI
These kernels must have NLS_ASCII set after bb6d7a05b, or else they
cannot mount the ESP as /boot and boot fails. This kconfig option will
be added to the pmb efi kconfig check so that this is caught in the
future pre-merge.
fixes 3909b1dbf and bb6d7a05b
[ci:skip-build] already built successfully in CI
Heavily based on z3ntu's work on FP5, thanks for all your work!
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
[ci:skip-build]: already built successfully in CI
pipewire-media-session was dropped in alpine in
4dc6a181bf590339f29a279fb7c4b9ae3c26c5fa, more than one year ago, so
this should be safe
While at it, also drop pipewire dependency, that is now a dependency
of postmarketos-base-ui
pipewire-media-session was dropped in alpine in
4dc6a181bf590339f29a279fb7c4b9ae3c26c5fa, more than one year ago, so
this should be safe
While at it, also drop the dep on pipewire, since it's taken care by
pmos-base-ui now
Device uses heimdall flash method by default, with uppercase
partition name in it's PIT file. This conflicts with flash on update,
because in Linux partitions named in lowercase. To resolve this conflict,
default flash method changed to fastboot. Heimdall still can be used with
`--method` flag: `pmbootstrap flasher --method heimdall-bootimg flash_kernel`
- enable flash on update flag.
- change default flash method to 'fastboot'
U-boot doesn't output bootscript logs, which makes it hard to debug.
Put bootscript to prebootscript section. Preboot is executed before
boot, and u-boot displays it's logs.
- Drop -mesa subpackage, this is handled by postmarketos-base now
- Add 'quiet' kernel cmdline param to hide kernel messages on boot by
default
- set chassis type to 'desktop'
- re-add firmware-ath6kl, this used to be included in the old
tablet-x86uefi but was accidentally dropped when that was merged into
this generic device package
- adds kconfigcheck-containers
- adds missing kconfigcheck-community options
- adds some missing dynamic debug stuff
- also adds kconfig options required by libcamera, because why not.
[ci:skip-build]: already built successfully in CI
Reserve 256MB for CMA, and of those use 192MB as VRAM.
The default value from the kernel side causes graphical issues with e.g.
phosh, so increase it so we have some more VRAM to work with.
[ci:skip-build]: already built successfully in CI
