commit ecd75ad514 upstream.
For some reason, some early WD drives spin up and down drives
erratically when the link is put into slumber mode which can reduce
the life expectancy of the device significantly. Unfortunately, we
don't have full list of devices and given the nature of the issue it'd
be better to err on the side of false positives than the other way
around. Let's disable LPM on all WD devices which match one of the
known problematic model prefixes and are SATA-I.
As horkage list doesn't support matching SATA capabilities, this is
implemented as two horkages - WD_BROKEN_LPM and NOLPM. The former is
set for the known prefixes and sets the latter if the matched device
is SATA-I.
Note that this isn't optimal as this disables all LPM operations and
partial link power state reportedly works fine on these; however, the
way LPM is implemented in libata makes it difficult to precisely map
libata LPM setting to specific link power state. Well, these devices
are already fairly outdated. Let's just disable whole LPM for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Nikos Barkas <levelwol@gmail.com>
Reported-and-tested-by: Ioannis Barkas <risc4all@yahoo.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=57211
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9013d64e66 upstream.
On Armada 370/XP SoCs, once a disk is removed from a SATA port, then the
re-plug events are not detected by the sata_mv driver. This patch fixes
the issue by updating the PHY speed in the LP_PHY_CTL register (0x58)
according to the SControl speed.
Note that this fix is only applied if the compatible string
"marvell,armada-370-sata" is found in the SATA DT node.
Fixes: 9ae6f740b4 ("arm: mach-mvebu: add support for Armada 370 and Armada XP with DT")
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1f5c73bd5 upstream.
The sata_mv driver supports the SATA IP found in several Marvell SoCs.
As some new SATA registers have been introduced with the Armada 370/XP
SoCs, a way to identify them is needed.
This patch introduces a new compatible string for the SATA IP found in
Armada 370/XP SoCs.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Lior Amsalem <alior@marvell.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 747d35bd9b upstream.
Depending on the implementation strcmp might return the difference between
two strings not only -1,0,1 consequently
if (strcmp (a,b) == -1)
might lead to taking the wrong branch
-> compare with < 0 instead,
which in any case is more canonical.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85c5e0d451 upstream.
The 'get_burstcount' function can in some circumstances 'return -EBUSY' which
in tpm_stm_i2c_send is stored in an 'u32 burstcnt'
thus converting the signed value into an unsigned value, resulting
in 'burstcnt' being huge.
Changing the type to u32 only does not solve the problem as the signed
value is converted to an unsigned in I2C_WRITE_DATA, resulting in the
same effect.
Thus
-> Change type of burstcnt to u32 (the return type of get_burstcount)
-> Add a check for the return value of 'get_burstcount' and propagate a
potential error.
This makes also sense in the 'I2C_READ_DATA' case, where the there is no
signed/unsigned conversion.
found by coverity
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7729a4153 upstream.
Similarly to other Apple products, MBA 1,1 needs a specific quirk.
Pin 0x18 must be set to VREF_50 to have sound output. This was no
longer done since commit 1a97b7f, resulting in a mute built-in speaker.
This patch corrects the regression by creating a fixup for the MBA 1,1.
Fixes: 1a97b7f227 ("ALSA: hda/realtek - Remove the last static quirks for ALC882")
Tested-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80ab8eae70 upstream.
The PCI devices with DMA masks smaller than 32bit should enable
CONFIG_ZONE_DMA. Since the recent change of page allocator, page
allocations via dma_alloc_coherent() with the limited DMA mask bits
may fail more frequently, ended up with no available buffers, when
CONFIG_ZONE_DMA isn't enabled. With CONFIG_ZONE_DMA, the system has
much more chance to obtain such pages.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=68221
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43a8e50a46 upstream.
AD1986A mic pins (0x1d and 0x1f) share the same widget for controlling
the loopback volume/mute, but the generic parser didn't check it.
This ended up with the duplicated controls for the same effect.
This patch adds the check of the duplication for avoiding it.
After this fix, there will be only one control although it affects
both paths; this remaining issue should be fixed later in a different
patch.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66621
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 770bd4bf2e upstream.
The lack of comma leads to the wrong channel for an SPDIF channel.
Unfortunately this wasn't caught by compiler because it's still a
valid expression.
Reported-by: Alexander Aristov <aristov.alexander@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3435479243 upstream.
Latest evaluation of the the device has given some patch file additions
for improved performance.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e20970ada3 upstream.
The driver defines ADAU1701_SEROCTL_WORD_LEN_16 as 0x10 while it should be b10,
so 0x2. This patch fixes it.
Reported-by: Magnus Reftel <magnus.reftel@lockless.no>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74142ffc0b upstream.
The regmap used by max77686 MFD driver was not freed with regmap_exit()
on driver exit. This lead to leak of resources.
Replace regmap_init_i2c() call in driver probe with initialization of
managed register map so the regmap will be properly freed by the device
management code.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad85ace07a upstream.
Currently, if we use perf kvm --guestkallsyms --guestmodules report, we
can not get the perf information from perf data file. All sample are
shown as unknown.
Reproducing steps:
# perf kvm --guestkallsyms /tmp/kallsyms --guestmodules /tmp/modules record -a sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.624 MB perf.data.guest (~27260 samples) ]
# perf kvm --guestkallsyms /tmp/kallsyms --guestmodules /tmp/modules report |grep %
100.00% [guest/6471] [unknown] [g] 0xffffffff8164f330
This bug was introduced by 207b57926 (perf kvm: Fix regression with guest machine creation).
In original code, it uses perf_session__find_machine(), it means we deliver symbol to machine
which has the same pid, if no machine found, deliver it to *default* guest. But if we use
perf_session__findnew_machine() here, if no machine was found, new machine with pid will be built
and added. Then the default guest which with pid == 0 will never get a symbol.
And because the new machine initialized here has no kernel map created, the symbol delivered to
it will be marked as "unknown".
This patch here is to revert commit 207b57926 and fix the SEGFAULT bug in another way.
Verification steps:
# ./perf kvm --guestkallsyms /home/kallsyms --guestmodules /home/modules record -a sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.651 MB perf.data.guest (~28437 samples) ]
# ./perf kvm --guestkallsyms /home/kallsyms --guestmodules /home/modules report |grep %
22.64% :6471 [guest.kernel.kallsyms] [g] update_rq_clock.part.70
19.99% :6471 [guest.kernel.kallsyms] [g] d_free
18.46% :6471 [guest.kernel.kallsyms] [g] bio_phys_segments
16.25% :6471 [guest.kernel.kallsyms] [g] dequeue_task
12.78% :6471 [guest.kernel.kallsyms] [g] __switch_to
7.91% :6471 [guest.kernel.kallsyms] [g] scheduler_tick
1.75% :6471 [guest.kernel.kallsyms] [g] native_apic_mem_write
0.21% :6471 [guest.kernel.kallsyms] [g] apic_timer_interrupt
Signed-off-by: Dongsheng Yang <yangds.fnst@cn.fujitsu.com>
Acked-by: David Ahern <dsahern@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Link: http://lkml.kernel.org/r/1387564907-3045-1-git-send-email-yangds.fnst@cn.fujitsu.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa8cf57c92 upstream.
Some GPIO users, such as fixed-regulator, request GPIO output with
initial value of 1. This was ignored by sunxi driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75ea799df4 upstream.
The current MAX8907 driver has two issues related to weekday value
handling:
1)
The HW WEEKDAY register has range 0..6 rather than 1..7 as documented.
Note that I validated the actual HW range by observing the HW register
roll from 6->0 rather than 6->7->1 as would otherwise be expected.
This matches Linux's tm_wday range of 0..6.
When the CMOS RAM content is lost, the date returned from the device is
2007-01-01 00:00:00, which is a Monday. The WEEKDAY register reads 1 in
this case. This matches the numbering in Linux's tm_wday field.
Hence we should write Linux's tm_wday value to the register without
modifying it. Hence, remove the +1/-1 calculations for WEEKDAY/tm_wday.
2)
There's no need to make alarms match on the WEEKDAY register, since the
other fields together uniquely define the alarm date/time. Ignoring the
WEEKDAY value in the match isolates the driver from any incorrect value in
the current time copy of the WEEKDAY register.
Each change individually, or both together, solves an issue that I
observed; "hwclock -r" would time out waiting for its alarm to fire if the
CMOS RAM content had been lost, and hence the WEEKDAY register value
mismatched what the driver expected it to be. "hwclock -w" would solve
this by over-writing the HW default WEEKDAY register value with what the
driver expected.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6a484520c upstream.
In commit 85747f ("PATCH] parport: add NetMOS 9805 support") Max added
the PCI ID for NetMOS 9805 based on a Debian bug report from 2k4 which
was at the v2.4.26 time frame. The patch made into 2.6.14.
Shortly before that patch akpm merged commit 296d3c783b ("[PATCH] Support
NetMOS based PCI cards providing serial and parallel ports") which made
into v2.6.9-rc1.
Now we have two different entries for the same PCI id.
I have here the NetMos 9805 which claims to support SPP/EPP/ECP mode.
This patch takes Max's entry for titan_1284p1 (base != -1 specifies the
ioport for ECP mode) and replaces akpm's entry for netmos_9805 which
specified -1 (=none). Both share the same PCI-ID (my card has subsystem
0x1000 / 0x0020 so it should match PCI_ANY).
While here I also drop the entry for titan_1284p2 which is the same as
netmos_9815.
Cc: Maximilian Attems <maks@stro.at>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e078146df upstream.
With b8668fd0a7 "s390/uapi: change struct statfs[64] member types
to unsigned values" the size of a couple of struct statfs64 member got
incorrectly changed from 64 to 32 bit for 32 bit builds.
Fix this by changing the type of couple of struct statfs64 members from
unsigned long to unsigned long long.
The definition of struct compat_statfs64 was correct however.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 743db27c52 upstream.
The diagnose code to be used is the contents of the base register (if not
zero), plus the displacement. The current code ignores the base register
contents. So let's fix that...
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3685f19e07 upstream.
Tegra chips have 4 or 5 identical UART modules embedded. UARTs C..E have
their MODEM-control signals tied off to a static state. However UARTs A
and B can optionally route those signals to/from package pins, depending
on the exact pinmux configuration.
When these signals are not routed to package pins, false interrupts may
trigger either temporarily, or permanently, all while not showing up in
the IIR; it will read as NO_INT. This will eventually lead to the UART
IRQ being disabled due to unhandled interrupts. When this happens, the
kernel may print e.g.:
irq 68: nobody cared (try booting with the "irqpoll" option)
In order to prevent this, enable UART_BUG_NOMSR. This prevents
UART_IER_MSI from being enabled, which prevents the false interrupts
from triggering.
In practice, this is not needed under any of the following conditions:
* On Tegra chips after Tegra30, since the HW bug has apparently been
fixed.
* On UARTs C..E since their MODEM control signals are tied to the correct
static state which doesn't trigger the issue.
* On UARTs A..B if the MODEM control signals are routed out to package
pins, since they will then carry valid signals.
However, we ignore these exceptions for now, since they are only relevant
if a board actually hooks up more than a 4-wire UART, and no currently
supported board does this. If we ever support a board that does, we can
refine the algorithm that enables UART_BUG_NOMSR to take those exceptions
into account, and/or read a flag from DT/... that indicates that the
board has hooked up and pinmux'd more than a 4-wire UART.
Reported-by: Olof Johansson <olof@lixom.net> # autotester
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c5320f8d7 upstream.
Fix the initialisation of older Quatech serial cards which are fitted with
the AMCC PCI Matchmaker interface chip.
Signed-off-by: Jonathan Woithe (jwoithe@just42.net)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d303b1b5fb upstream.
Add new PCI ID to support new model "Kaveri" family.
Signed-off-by: Philip Pokorny <ppokorny@penguincomputing.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1588c51cf6 upstream.
There was a copy/paste error when reading the nwe_pulse value.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0cc7c6c791 upstream.
Interrupts were being cleaned up late in the shutdown handler, it is possible
that an interrupt can occur and schedule a tasklet that runs after the port is
cleaned up. There is a null dereference due to this race condition with the
following stacktrace:
[<c02092b0>] (atmel_tasklet_func+0x514/0x814) from [<c001fd34>] (tasklet_action+0x70/0xa8)
[<c001fd34>] (tasklet_action+0x70/0xa8) from [<c001f60c>] (__do_softirq+0x90/0x144)
[<c001f60c>] (__do_softirq+0x90/0x144) from [<c001fa18>] (irq_exit+0x40/0x4c)
[<c001fa18>] (irq_exit+0x40/0x4c) from [<c000e298>] (handle_IRQ+0x64/0x84)
[<c000e298>] (handle_IRQ+0x64/0x84) from [<c000d6c0>] (__irq_svc+0x40/0x50)
[<c000d6c0>] (__irq_svc+0x40/0x50) from [<c0208060>] (atmel_rx_dma_release+0x88/0xb8)
[<c0208060>] (atmel_rx_dma_release+0x88/0xb8) from [<c0209740>] (atmel_shutdown+0x104/0x160)
[<c0209740>] (atmel_shutdown+0x104/0x160) from [<c0205e8c>] (uart_port_shutdown+0x2c/0x38)
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f248dae13 upstream.
byBBPreEDIndex value is initially 0, this means that from
cold BBvUpdatePreEDThreshold is never set.
This means that sensitivity may be in an ambiguous state,
failing to scan any wireless points or at least distant ones.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a21f00a50 upstream.
The latest version of NetworkManager does not recognize the device as wireless
without this change.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64e5acb09c upstream.
Use the right function to update frequency value.
If rx skb is probe response or beacon, the wrong frequency value can
cause problem that bss info can't be updated when it should be.
Fixes: 8318d78a44 ("cfg80211 API for channels/bitrates, mac80211 and driver conversion")
Signed-off-by: ZHAO Gang <gamerh2o@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4520286653 upstream.
The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0673effd41 upstream.
The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.
To be able to access the completion structure at teardown, it had to be moved
into the b43_wldev structure.
This patch also fixes a typo in a comment.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09164043f6 upstream.
In https://bugzilla.kernel.org/show_bug.cgi?id=67561, a locking dependency is reported
when b43 is used with hostapd, and rfkill is used to kill the radio output.
The lockdep splat (in part) is as follows:
======================================================
[ INFO: possible circular locking dependency detected ]
3.12.0 #1 Not tainted
-------------------------------------------------------
rfkill/10040 is trying to acquire lock:
(rtnl_mutex){+.+.+.}, at: [<ffffffff8146f282>] rtnl_lock+0x12/0x20
but task is already holding lock:
(rfkill_global_mutex){+.+.+.}, at: [<ffffffffa04832ca>] rfkill_fop_write+0x6a/0x170 [rfkill]
--snip--
Chain exists of:
rtnl_mutex --> misc_mtx --> rfkill_global_mutex
The fix is to move the initialization of the hardware random number generator
outside the code range covered by the rtnl_mutex.
Reported-by: yury <urykhy@gmail.com>
Tested-by: yury <urykhy@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91b0d11984 upstream.
Cleanup of iwl_mvm_leds was missing in case of error,
resulting in the following warning:
WARNING: at lib/kobject.c:196 kobject_add_internal+0x1f4/0x210()
kobject_add_internal failed for phy0-led with -EEXIST, don't try to register things with the same name in the same directory.
which prevents further reloads of the driver.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e202242ee upstream.
bit 14 is actually reserved and bit 12 & 13 should be used for
11ac capability in fw_cap_info.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9795229752 upstream.
It is u64 data received from firmware. Little endian to cpu
conversion is required here.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f699273d6a upstream.
The static analyser "cppcheck" shows the following typo:
drivers/net/wireless/rtlwifi/rtl8188ee/dm.c:1081]: (style) Same expression on both sides of '!='.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: David Binderman <dcb314@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9806eacf5d upstream.
This patch uses the newly introduced power index register routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc64057122 upstream.
The current number of RX buffers queued is 32, which is too small under
heavy load. That number is doubled.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c908c74e00 upstream.
Changes in the gain-control mechanism will require some changes in the header.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 619ce76f8b upstream.
The present code fails to set the linked state when an interface is
added.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9a758a8c9 upstream.
The initial USB driver did not use some register save locations in the
private data storage. To save some memory, a union was used to overlay these
variables with USB I/O components. In an update of the gain-control code,
these register save locations are now needed for USB drivers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62009b7f12 upstream.
Vendor driver rtl8188C_8192C_8192D_usb_linux_v3.4.2_3727.20120404 introduced
new firmware for these chips. The code try for the new file, and fall back to
the original firmware if the new file is not available.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fd77aec1a upstream.
This driver has a watchdog timer that attempts to reconnect when beacon frames
are not seen for 6 seconds. This patch disables that reconnect whenever the
device has never been connected.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65b9cc97c6 upstream.
The USB drivers were not updating the beacon statistics, which led to
false beacon loss indications.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f87f960b2f upstream.
Reported-by: Jan Prinsloo <janroot@gmail.com>
Tested-by: Jan Prinsloo <janroot@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit feffe09f51 upstream.
According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement a special ehci_write
for imx28.
Discussion for it at below:
http://marc.info/?l=linux-usb&m=137996395529294&w=2
Without this patcheset, imx28 works unstable at high AHB bus loading.
If the bus loading is not high, the imx28 usb can work well at the most
of time. There is a IC errata for this problem, usually, we consider
IC errata is a problem not a new feature, and this workaround is needed
for that, so we need to add them to stable tree 3.11+.
Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 543d7784b0 upstream.
There is a race in the hub driver between hub_disconnect() and
recursively_mark_NOTATTACHED(). This race can be triggered if the
driver is unbound from a device at the same time as the bus's root hub
is removed. When the race occurs, it can cause an oops:
BUG: unable to handle kernel NULL pointer dereference at 0000015c
IP: [<c16d5fb0>] recursively_mark_NOTATTACHED+0x20/0x60
Call Trace:
[<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<c16d6082>] usb_set_device_state+0x92/0x120
[<c16d862b>] usb_disconnect+0x2b/0x1a0
[<c16dd4c0>] usb_remove_hcd+0xb0/0x160
[<c19ca846>] ? _raw_spin_unlock_irqrestore+0x26/0x50
[<c1704efc>] ehci_mid_remove+0x1c/0x30
[<c1704f26>] ehci_mid_stop_host+0x16/0x30
[<c16f7698>] penwell_otg_work+0xd28/0x3520
[<c19c945b>] ? __schedule+0x39b/0x7f0
[<c19cdb9d>] ? sub_preempt_count+0x3d/0x50
[<c125e97d>] process_one_work+0x11d/0x3d0
[<c19c7f4d>] ? mutex_unlock+0xd/0x10
[<c125e0e5>] ? manage_workers.isra.24+0x1b5/0x270
[<c125f009>] worker_thread+0xf9/0x320
[<c19ca846>] ? _raw_spin_unlock_irqrestore+0x26/0x50
[<c125ef10>] ? rescuer_thread+0x2b0/0x2b0
[<c1264ac4>] kthread+0x94/0xa0
[<c19d0f77>] ret_from_kernel_thread+0x1b/0x28
[<c1264a30>] ? kthread_create_on_node+0xc0/0xc0
One problem is that recursively_mark_NOTATTACHED() uses the intfdata
value and hub->hdev->maxchild while hub_disconnect() is clearing them.
Another problem is that it uses hub->ports[i] while the port device is
being released.
To fix this race, we need to hold the device_state_lock while
hub_disconnect() changes the values. (Note that usb_disconnect()
and hub_port_connect_change() already acquire this lock at similar
critical times during a USB device's life cycle.) We also need to
remove the port devices after maxchild has been set to 0, instead of
before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: "Du, Changbin" <changbinx.du@intel.com>
Tested-by: "Du, Changbin" <changbinx.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9005355af2 upstream.
If CONFIG_PCI is enabled, make sure xhci_cleanup_msix()
doesn't try to free a bogus PCI IRQ or dereference an invalid
pci_dev when the xHCI device is actually a platform_device.
This patch should be backported to kernels as old as 3.9, that
contain the commit 52fb61250a
"xhci-plat: Don't enable legacy PCI interrupts."
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
