Previously, we just reset the ring register in the context image such
that we could skip over the broken batch and emit the closing
breadcrumb. However, on resume the context image and GPU state would be
reloaded, which may have been left in an inconsistent state by the
reset. The presumption was that at worst it would just cause another
reset and skip again until it recovered, however it seems just as likely
to cause an unrecoverable hang. Instead of risking loading an incomplete
context image, restore it back to the default state.
v2: Fix up off-by-one from including the ppHSWP in with the register
state.
v3: Use a ring local to compact a few lines.
v4: Beware setting the ring local before checking for a NULL request.
References: https://bugs.freedesktop.org/show_bug.cgi?id=105304
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20180428111532.15819-1-chris@chris-wilson.co.uk
Revision 7 of PCIe dongle interface increases the item size of tx and rx
complete rings to accommodate extra payload for new feature. This patch
simply bump up the size of these two rings without adding the support
for utilizing the new space. This makes brcmfmac compatible with rev7
firmware.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A hostready signal is introduced to inform firmware through mailbox
doorbell1 when common ring initialized or D3 exited.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The information in the firmware mapping does not need to be modified
so it can be static const.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The enum nl80211_band used to retrieve wiphy->bands is the same as
wiphy->bands->band which is checked by wiphy_register(). So it can be used
directly as parameter of ieee80211_channel_to_frequency().
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Provides a timestamp in bss information so user space can see when the
bss info was updated. Since tsf is not available from the dongle events
boottime is reported instead.
Reported-by: Dmitry Shmidt <dimitrysh@google.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The mac address for p2pdev must be different from the primary interface
due to firmware requirement. Add an explicit check for this requirement
if user-space provides a mac address.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in comment and in the ord_data text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename several macros that contain mispellings of UNKNOWN
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a potential execution path in which variable ret is returned
without being properly initialized previously.
Fix this by storing the value returned by function
rsi_usb_master_reg_write into _ret_.
Addresses-Coverity-ID: 1468407 ("Uninitialized scalar variable")
Fixes: 16d3bb7b2f ("rsi: disable fw watchdog timer during reset")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function rsi_hal_key_config returns before reaching code at line
922 if (status), hence this code is structurally dead.
Fix this by storing the value returned by rsi_hal_load_key
into _status_ for its further evaluation and use.
Addresses-Coverity-ID: 1468409 ("Structurally dead code")
Fixes: 4fd6c4762f ("rsi: roaming enhancements")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pm_runtime handles sdio power on and power off transitions.
An old workaround for trying to control the power explicitly from the
driver was in fact causing failures on suspend/resume as the mmc layer
already power the module on resume.
In case of resume pm_runtime_get sync returns a positive device's usage
count causing the driver to try an re-initialize an already initialized
device. This was causing sdio bus failure on resume.
Remove this manual power on/off sequence as it is in-fact not needed.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
dma_tx_fragment() is never called in atomic context.
dma_tx_fragment() is only called by b43legacy_dma_tx(), which is
only called by b43legacy_tx_work().
b43legacy_tx_work() is only set a parameter of INIT_WORK() in
b43legacy_wireless_init().
Despite never getting called from atomic context,
dma_tx_fragment() calls alloc_skb() with GFP_ATOMIC,
which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL,
which can sleep and improve the possibility of sucessful allocation.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During changing virtual interface, keep using previous net device
mac address.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When interface type changed, firmware using a new connction pointer.
We need Re-configure the mac address.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For user configurated mac address, directly set to firmware with no change.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The check within mt76_txq_send_burst is not enough, as it happens after
a first frame has already been queued up
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avoids having the tid or station entry disappear prematurely.
Also cancel the reorder work earlier to avoid further processing delayed
by waiting for the lock to be released
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a spinlock in mt76_rx_complete. Without this, multiple stats updates
could happen in parallel, which can lead to deadlocks. There are
probably more corner cases fixed by this change.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix is_mt7612 routine since asic version is set in mt76_dev revision
field and not in mt76x2_dev one.
Moreover remove mt76x2_dev rev field since it is never used in the
driver
Fixes: 7bc04215a6 ('mt76: add driver code for MT76x2e')
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Some preparations for new hardware;
* A workaround to rescan the bus for the rare situation when older
devices become irresponsive,
* Hardening of the firmware loading code to avoid issues with
corrupted files;
* A few clean-ups and bugfixes.
-----BEGIN PGP SIGNATURE-----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=pOKl
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2018-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Second batch of iwlwifi patches for 4.18
* Some preparations for new hardware;
* A workaround to rescan the bus for the rare situation when older
devices become irresponsive,
* Hardening of the firmware loading code to avoid issues with
corrupted files;
* A few clean-ups and bugfixes.
This patch adds a LCD driver supporting the OTM3225A LCD SoC
from ORISE Technology. This device can drive TFT LC panels having a
resolution of 240x320 pixels. After initializing the OTM3225A using
it's SPI interface it switches to use 16-bib RGB as external
display interface.
Signed-off-by: Felix Brack <fb@ltec.ch>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The documentation was wrong, gpiod_get_direction() returns 0/1 instead
of the GPIOF_* flags. The docs were fixed with commit 94fc73094a
("gpio: correct docs about return value of gpiod_get_direction"). Now,
fix this user (until a better, system-wide solution is in place).
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some panels (i.e. N116BGE-L41), in their power sequence specifications,
request a delay between set the PWM signal and enable the backlight and
between clear the PWM signal and disable the backlight. Add support for
the new post-pwm-on-delay-ms and pwm-off-delay-ms proprieties to meet
the timings.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Hardware needs a delay between setting an initial (non-zero) PWM and
enabling the backlight using GPIO. The post-pwm-on-delay-ms specifies
this delay in milli seconds. Hardware also needs a delay between disabing
the backlight using GPIO and setting PWM value to 0. The pwm-off-delay-ms
is this delay in milli seconds.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Before this patch the enable signal was set before the PWM signal and
vice-versa on power off. This sequence is wrong, at least, it is on
the different panels datasheets that I checked, so I inverted the sequence
to follow the specs.
For reference the following panels have the mentioned sequence:
- N133HSE-EA1 (Innolux)
- N116BGE (Innolux)
- N156BGE-L21 (Innolux)
- B101EAN0 (Auo)
- B101AW03 (Auo)
- LTN101NT05 (Samsung)
- CLAA101WA01A (Chunghwa)
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add Device Tree bindings for RAVE SP backlight driver - an MFD cell of
parent RAVE SP driver (documented in
Documentation/devicetree/bindings/mfd/zii,rave-sp.txt).
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver provides access to RAVE SP backlight control
functionality.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Give a clear testcase for people wishing to change this code. It is also
a reminder for me if people ask about it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The PiTFT (ili9340) has a hardware reset circuit that resets only
on power-on and not on each reboot through a gpio like the
rpi-display does. As a result, we need to always apply the
rotation value regardless of the display "on/off" state.
Moved the rotation setting code below out_enable:.
Signed-off-by: Tom Callaway <tcallawa@redhat.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423161639.14420-1-tcallawa@redhat.com
The Dell XPS 13 9360 uses a QCA Rome chip which needs to be reset
(and have its firmware reloaded) for bluetooth to work after
suspend/resume.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836
Cc: stable@vger.kernel.org
Cc: Garrett LeSage <glesage@redhat.com>
Reported-and-tested-by: Garrett LeSage <glesage@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
tracepoints to bpf core were added as a way to provide introspection
to bpf programs and maps, but after some time it became clear that
this approach is inadequate, so prog_id, map_id and corresponding
get_next_id, get_fd_by_id, get_info_by_fd, prog_query APIs were
introduced and fully adopted by bpftool and other applications.
The tracepoints in bpf core started to rot and causing syzbot warnings:
WARNING: CPU: 0 PID: 3008 at kernel/trace/trace_event_perf.c:274
Kernel panic - not syncing: panic_on_warn set ...
perf_trace_bpf_map_keyval+0x260/0xbd0 include/trace/events/bpf.h:228
trace_bpf_map_update_elem include/trace/events/bpf.h:274 [inline]
map_update_elem kernel/bpf/syscall.c:597 [inline]
SYSC_bpf kernel/bpf/syscall.c:1478 [inline]
Hence this patch deletes tracepoints in bpf core.
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Reported-by: syzbot <bot+a9dbb3c3e64b62536a4bc5ee7bbd4ca627566188@syzkaller.appspotmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Unfortunately some DSDTs issue bogus i2c reads to non existing devices
resulting in -EREMOTEIO errors because the non existing device of course
does not ack.
This happens e.g. from the The Asus T100TA's _BIX method, the DSDT on
the T100TA defines 2 resources on the I2C1 bus:
Name (EHID, ResourceTemplate ()
{
I2cSerialBusV2 (0x005B, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.I2C1",
0x00, ResourceConsumer, , Exclusive,
)
})
OperationRegion (EHOR, GenericSerialBus, Zero, 0x0100)
Field (EHOR, BufferAcc, NoLock, Preserve)
{
Connection (EHID),
Offset (0x01),
AccessAs (BufferAcc, AttribBytes (0x10)),
ABCD, 8
}
Name (UMPC, ResourceTemplate ()
{
I2cSerialBusV2 (0x0066, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.I2C1",
0x00, ResourceConsumer, , Exclusive,
)
})
The _BIX method does a single read (on each BIX() call) from the EHID
device through the ABCD Field, only to completely ignore the result.
This read always fails as there is no i2c client at address 0x5b.
The _BIX method also does several reads from the UMPC device and actually
uses the results of those to provide battery information.
IIRC I've also seen some DSTDs which do an i2c read to detect if a device
is present, also leading to false positive errors being logged.
Esp. the _BIX use is problematic as the _BIX method gets called
periodically to monitor battery status.
This commit stops the logs from filling up with errors like these:
[ 57.327858] i2c i2c-0: i2c read 16 bytes from client@0x5b starting at
reg 0x1 failed, error: -121
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When we get an error doing an ACPI SerialBus I2C OpRegion read log some
useful details, like the client address and which register is being
read.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jeremy Cline correctly points out in rhbz#1514836 that a device where the
QCA rome chipset needs the USB_QUIRK_RESET_RESUME quirk, may also ship
with a different wifi/bt chipset in some configurations.
If that is the case then we are needlessly penalizing those other chipsets
with a reset-resume quirk, typically causing 0.4W extra power use because
this disables runtime-pm.
This commit moves the DMI table check to a btusb_check_needs_reset_resume()
helper (so that we can easily also call it for other chipsets) and calls
this new helper only for QCA_ROME chipsets for now.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836
Cc: stable@vger.kernel.org
Cc: Jeremy Cline <jcline@redhat.com>
Suggested-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit f44cb4b19e ("Bluetooth: btusb: Fix quirk for Atheros
1525/QCA6174") is causing bluetooth to no longer work for several
people, see: https://bugzilla.redhat.com/show_bug.cgi?id=1568911
So lets revert it for now and try to find another solution for
devices which need the modified quirk.
Cc: stable@vger.kernel.org
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The PCIe-IDIO-24 features 8 bits of TTL GPIO which may be configured for
output or input. This patch fixes an off-by-one error in the loop
conditional for the get_multiple callback so that the TTL GPIO are
handled.
Fixes: ca37081595 ("gpio: pcie-idio-24: Implement get_multiple/set_multiple callbacks")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
It adds capability register description to documentation.
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It allows mlxcpld driver to be connected to pre-defined adapter number
equal or greater than one, in order to avoid current limitation, assuming
usage of id number one only.
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It fixes report about supported functionality.
Functionality can be different up to CPLD capability.
Fixes: 6bec23bff9 (i2c: mlxcpld: add master driver for mellanox systems)
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It adds support for smbus block read transaction. CPLD smbus block read bit
of capability register is verified during driver initialization, and driver
data is updated if such capability is available. In case an upper layer
requests a read transaction of length one and expects that length will be
the first received byte, driver will notify CPLD about SMBus block read
transaction flavor, so CPLD will know to execute such kind of transaction.
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It adds support for extended length of read and write transactions.
New CPLD logic allows double size of the read and write transactions
length. This feature is verified through capability register, which is
renamed from unclear LPF_REG to CPBLTY_REG. Two bits 5 and 6 of these
register are used for length capability detection, while only 01
combination indicates support of extended transaction length.
Others mean lack of such support.
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The usage of of_device_get_match_data() reduce the code size a bit.
Also, the only way to call mtk_i2c_probe() is to match an entry in
mtk_i2c_of_match[], so of_id cannot be NULL.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Restoring configuration registers is only needed when we hand control
to the firmware. This is never the case with runtime power
management. The device will autosuspend whenever not used, so avoid
useless register writes by defining suspend/resume only, and not
runtime_suspend/runtime_resume.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With FIFO enabled it is possible to read multiple bytes
at once in the interrupt handler as long as RXRDY is
set. This may also reduce the number of interrupts.
This patch polls RXRDY and reads all available bytes at
once.
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[wsa: reformatted comment]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
