For failed commands with valid sense data (e.g. NCQ commands),
scsi_check_sense() is used in ata_analyze_tf() to determine if the
command can be retried. In such case, rely on this decision and ignore
the command error mask based decision done in ata_worth_retry().
This fixes useless retries of commands such as unaligned writes on zoned
disks (TYPE_ZAC).
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently, libata ignores requests RQF_QUIET flag and print error
messages for failed commands, regardless if this flag is set in the
command request. Fix this by introducing the ata_eh_quiet() function and
using this function in ata_eh_link_autopsy() to determine if the EH
context should be quiet. This works by counting the number of failed
commands and the number of commands with the quiet flag set. If both
numbers are equal, the the EH context can be set to quiet and all error
messages suppressed. Otherwise, only the error messages for the failed
commands are suppressed and the link Emask and irq_stat messages printed.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
For a successful setting of the device transfer speed mode in
ata_dev_set_mode(), do not print the message
"ataX.XX: configured for xxx" if the EH context has the quiet flag set,
unless the device port is being reset.
This preserves the output of the message during device scan but removes
it in the case of a simple device revalidation such as trigerred by
enabling the NCQ I/O priority feature of the device
e.g. echo 1 > /sys/block/sdxx/device/ncq_iprio_enable
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add proper error string output for ATA_ERR_NCQ and ATA_ERR_NODEV_HINT
instead of returning "unknown error".
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
- Fix for a 4.17-rc1 change to dm-bufio's buffer alignment.
- Fixes for a few sparse warnings.
- Remove VLA usage in DM mirror target.
- Improve DM thinp Documentation for the "read_only" feature.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJa9Gn4AAoJEMUj8QotnQNa+6sH/0lu9XA7fpaopD29wPkjtFLg
nDY8yCBrBvo1GRQBCAM3TWYDdTYLgO0srn24y9AM0AnhuiR+YFeDuoMyhzIQjWay
X+RGgiMtLwroLWO9t7hhP1eK3u3SX+40bhvle6vNOn/KGb7XOuFnEksUJ85B9pJZ
xF1aGos8+YIXTqBRP4RLJPWKPme1HIpdVGUcwnt9fW3J9PYzkN9xIry/cow0JWEl
xmr69l2KpOQ7jVpcBhA52NDosW/LCOipyr9mhe0+lq60BDcsCbjCkK5p6F38Ufa8
+24cqgdT2fdbogL3JTfs0lIgrOaLOhYmL5qJemopcxE6TKXvP6AzHhihlT48fNA=
=w2u8
-----END PGP SIGNATURE-----
Merge tag 'for-4.17/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a stable fix for DM integrity to use kvfree
- fix for a 4.17-rc1 change to dm-bufio's buffer alignment
- fixes for a few sparse warnings
- remove VLA usage in DM mirror target
- improve DM thinp Documentation for the "read_only" feature
* tag 'for-4.17/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm thin: update Documentation to clarify when "read_only" is valid
dm mirror: remove VLA usage
dm: fix some sparse warnings and whitespace in dax methods
dm cache background tracker: fix sparse warning
dm bufio: fix buffer alignment
dm integrity: use kvfree for kvmalloc'd memory
sata_nv sets the block bounce limit to the reduce dma mask for ATAPI
devices, which means that the iommu or swiotlb already take care of
the bounce buffering, and the block bouncing can be removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
When we perform the following command lines:
$ perf record -e "{cycles,branches}" ./div
$ perf annotate main --stdio
The output shows only the first event, "cycles" and the displaying
format is not correct.
Percent | Source code & Disassembly of div for cycles (44550 samples)
-----------------------------------------------------------------------------------
:
:
:
: Disassembly of section .text:
:
: 00000000004004b0 <main>:
: main():
:
: return i;
: }
:
: int main(void)
: {
0.00 : 4004b0: push %rbx
: int i;
: int flag;
: volatile double x = 1212121212, y = 121212;
:
: s_randseed = time(0);
0.00 : 4004b1: xor %edi,%edi
: srand(s_randseed);
0.00 : 4004b3: mov $0x77359400,%ebx
:
: return i;
: }
The issue is that the value of the 'nr_percent' variable is hardcoded to
1. This patch fixes it.
With this patch, the output is:
Percent | Source code & Disassembly of div for cycles (44550 samples)
-----------------------------------------------------------------------------------
:
:
:
: Disassembly of section .text:
:
: 00000000004004b0 <main>:
: main():
:
: return i;
: }
:
: int main(void)
: {
0.00 0.00 : 4004b0: push %rbx
: int i;
: int flag;
: volatile double x = 1212121212, y = 121212;
:
: s_randseed = time(0);
0.00 0.00 : 4004b1: xor %edi,%edi
: srand(s_randseed);
0.00 0.00 : 4004b3: mov $0x77359400,%ebx
:
: return i;
: }
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes: f681d593d1 ("perf annotate: Remove disasm__calc_percent() from disasm_line__print()")
Link: http://lkml.kernel.org/r/1525881435-4092-1-git-send-email-yao.jin@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf test "probe libc's inet_pton & backtrace it with ping" fails on
4.17.0rc3 on s/390. It turned out that function __inet_pton is reported
as inline:
[root@s8360047 perf]# ./perf script -i /tmp/perf.data.111
ping 12457 [000] 1584.478959: probe_libc:inet_pton: (3ffb5a347e8)
1347e8 __inet_pton (inlined)
f19d7 gaih_inet.constprop.5 (/usr/lib64/libc-2.24.so)
f4c3f __GI_getaddrinfo (inlined)
410b main (/usr/bin/ping)
Allow __inet_pton listed as inline.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Link: http://lkml.kernel.org/r/20180503065837.71043-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The 88E6141/6341 switches (also known as Topaz) have 1 SGMII lane,
which can be configured the same way as the SERDES lane on 88E6390.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for U32 filter by using an HW only feature called
Flexible RX Parser. This allow us to match any given packet field with a
pattern and accept/reject or even route the packet to a specific DMA
channel.
Right now we only support acception or rejection of frame and we only
support simple rules. Though, the Parser has the flexibility of jumping to
specific rules as an if condition so complex rules can be established.
This is only supported in GMAC5.10+.
The following commands can be used to test this code:
1) Setup an ingress qdisk:
# tc qdisc add dev eth0 handle ffff: ingress
2) Setup a filter (e.g. filter by IP):
# tc filter add dev eth0 parent ffff: protocol ip u32 match ip \
src 192.168.0.3 skip_sw action drop
In every tests performed we always used the "skip_sw" flag to make sure
only the RX Parser was involved.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support of hardware rx-vlan-offload to VF driver.
VF uses mailbox to convey PF to configure the hardware.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver for Microchip LAN87XX T1 PHYs
This patch support driver for Microchp T1 PHYs.
There will be followup patches to this driver to support T1 PHY
features such as cable diagnostics, signal quality indicator(SQI),
sleep and wakeup (TC10) support.
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the user passed the right value to
sbitmap_queue_min_shallow_depth().
Acked-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We don't expect the async depth to be smaller than the wake batch
count for sbitmap, but just in case, inform sbitmap of what shallow
depth kyber may use.
Acked-by: Paolo Valente <paolo.valente@linaro.org>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If our shallow depth is smaller than the wake batching of sbitmap,
we can introduce hangs. Ensure that sbitmap knows how low we'll go.
Acked-by: Paolo Valente <paolo.valente@linaro.org>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The sbitmap queue wake batch is calculated such that once allocations
start blocking, all of the bits which are already allocated must be
enough to fulfill the batch counters of all of the waitqueues. However,
the shallow allocation depth can break this invariant, since we block
before our full depth is being utilized. Add
sbitmap_queue_min_shallow_depth(), which saves the minimum shallow depth
the sbq will use, and update sbq_calc_wake_batch() to take it into
account.
Acked-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bfqd->sb_shift was attempted used as a cache for the sbitmap queue
shift, but we don't need it, as it never changes. Kill it with fire.
Acked-by: Paolo Valente <paolo.valente@linaro.org>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It doesn't change, so don't put it in the per-IO hot path.
Acked-by: Paolo Valente <paolo.valente@linaro.org>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reserved tags are used for error handling, we don't need to
care about them for regular IO. The core won't call us for these
anyway.
Acked-by: Paolo Valente <paolo.valente@linaro.org>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
On the Huawei D03 development board the system UART is
the UART connected on the LPC bus.
The profile for the device driver required for this HW
is as follows:
- platform driver
- 16550
- ACPI support
- polling mode support
- IO space support
In principle we should use the PNP driver (8250_dw.c) for
8250-devices with ACPI FW. However since this driver does
not support PNP devices, and modifying the PNP core code
to support it is not worth the effort, use the generic
8250 isa driver.
For this, we setup the pdev platform data for the serial
8250 port.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Since we no longer use the MFD APIs to enumerate the
child devices on the bus, use the platform driver APIs
directly.
In this patch we iterate of the children devices for the
host, and create a platform device directly per child.
For the iterating, we match the child ACPI HID against a
known list of supported child devices and their respective
ACPIs HID, to find the device name and any other
supplementary data.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The MFD APIs should only be used by drivers in
drivers/mfd. It is not worth splitting the driver to have
separate parts in drivers/bus and drivers/mfd, so just
drop MFD API usage.
As a solution, we will use the platform device APIs directly
to achieve the same as we had when using MFD APIs.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
When sending packets as fast as possible using "cangen -g 0 -i -x", the
HI-3110 occasionally latches the interrupt pin high on completion of a
packet, but doesn't set the TXCPLT bit in the INTF register. The INTF
register contains 0x00 as if no interrupt has occurred. Even waiting
for a few milliseconds after the interrupt doesn't help.
Work around this apparent erratum by instead checking the TXMTY bit in
the STATF register ("TX FIFO empty"). We know that we've queued up a
packet for transmission if priv->tx_len is nonzero. If the TX FIFO is
empty, transmission of that packet must have completed.
Note that this is congruent with our handling of received packets, which
likewise gleans from the STATF register whether a packet is waiting in
the RX FIFO, instead of looking at the INTF register.
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Trivial fix to spelling mistake in dprintf message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
hi3110_get_berr_counter() may run concurrently to the rest of the driver
but neglects to acquire the lock protecting access to the SPI device.
As a result, it and the rest of the driver may clobber each other's tx
and rx buffers.
We became aware of this issue because transmission of packets with
"cangen -g 0 -i -x" frequently hung. It turns out that agetty executes
->do_get_berr_counter every few seconds via the following call stack:
CPU: 2 PID: 1605 Comm: agetty
[<7f3f7500>] (hi3110_get_berr_counter [hi311x])
[<7f130204>] (can_fill_info [can_dev])
[<80693bc0>] (rtnl_fill_ifinfo)
[<806949ec>] (rtnl_dump_ifinfo)
[<806b4834>] (netlink_dump)
[<806b4bc8>] (netlink_recvmsg)
[<8065f180>] (sock_recvmsg)
[<80660f90>] (___sys_recvmsg)
[<80661e7c>] (__sys_recvmsg)
[<80661ec0>] (SyS_recvmsg)
[<80108b20>] (ret_fast_syscall+0x0/0x1c)
agetty listens to netlink messages in order to update the login prompt
when IP addresses change (if /etc/issue contains \4 or \6 escape codes):
https://git.kernel.org/pub/scm/utils/util-linux/util-linux.git/commit/?id=e36deb6424e8
It's a useful feature, though it seems questionable that it causes CAN
bit error statistics to be queried.
Be that as it may, if hi3110_get_berr_counter() is invoked while a frame
is sent by hi3110_hw_tx(), bogus SPI transfers like the following may
occur:
=> 12 00 (hi3110_get_berr_counter() wanted to transmit
EC 00 to query the transmit error counter,
but the first byte was overwritten by
hi3110_hw_tx_frame())
=> EA 00 3E 80 01 FB (hi3110_hw_tx_frame() wanted to transmit a
frame, but the first byte was overwritten by
hi3110_get_berr_counter() because it wanted
to query the receive error counter)
This sequence hangs the transmission because the driver believes it has
sent a frame and waits for the interrupt signaling completion, but in
reality the chip has never sent away the frame since the commands it
received were malformed.
Fix by acquiring the SPI lock in hi3110_get_berr_counter().
I've scrutinized the entire driver for further unlocked SPI accesses but
found no others.
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Cc: Stef Walter <stefw@redhat.com>
Cc: Karel Zak <kzak@redhat.com>
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When invoked for an I/O request rq, the prepare_request hook of bfq
increments reference counters in the destination bfq_queue for rq. In
this respect, after this hook has been invoked, rq may still be
transformed into a request with no icq attached, i.e., for bfq, a
request not associated with any bfq_queue. No further hook is invoked
to signal this tranformation to bfq (in general, to the destination
elevator for rq). This leads bfq into an inconsistent state, because
bfq has no chance to correctly lower these counters back. This
inconsistency may in its turn cause incorrect scheduling and hangs. It
certainly causes memory leaks, by making it impossible for bfq to free
the involved bfq_queue.
On the bright side, no transformation can still happen for rq after rq
has been inserted into bfq, or merged with another, already inserted,
request. Exploiting this fact, this commit addresses the above issue
by delaying the preparation of an I/O request to when the request is
inserted or merged.
This change also gives a performance bonus: a lock-contention point
gets removed. To prepare a request, bfq needs to hold its scheduler
lock. After postponing request preparation to insertion or merging, no
lock needs to be grabbed any longer in the prepare_request hook, while
the lock already taken to perform insertion or merging is used to
preparare the request as well.
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The function 'xfs_qm_dqiterate' doesn't iterate dquots at all, it
iterates all dquot blocks of a quota inode and clears the counters.
Therefore, change the name to something more descriptive so that we can
introduce a real dquot iterator later.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
DQALLOC is only ever used with xfs_qm_dqget*, and the only flag that the
_dqget family of functions cares about is DQALLOC. Therefore, change
it to a boolean 'can alloc?' flag for the dqget interfaces where that
makes sense.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
The quota initialization code needs an "uncached" variant of _dqget to
read in default quota limits and timers before the dquot cache is fully
set up. We've already split up _dqget into its component pieces so
create a fourth variant to address this need, and make dqread internal
to xfs_dquot.c again.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Separate the disk dquot read and allocation functionality into
two helper functions, then refactor dqread to call them directly.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Create two incore dquot initialization functions that will help us to
disentangle dqget and dqread.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Quotacheck only runs during mount, which means that there are no other
processes in the system that could be doing chown or chproj. Therefore
there's no potential for racing to attach dquots to the inode so we can
drop all the ILOCK and race detection bits from quotacheck.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
There are two uses of dqget here -- one is to return the dquot for a
given type and id, and the other is to return the dquot for a given type
and inode. Those are two separate things, so split them into two
smaller functions.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The flags argument is always zero, get rid of it.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move the dqget input checks to a separate function in preparation for
splitting up the dqget functionality.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Delegate the dquot cache handling (radix tree lookup and insertion) to
separate helper functions so that we can continue to simplify the body
of dqget.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
There's only one caller of DQNEXT and its semantics can be moved into a
separate function, so create the function and get rid of the flag.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
When dquot flush or purge fail there's no need to spam the logs, we've
already logged the IO error or fs shutdown that caused the flush
failures.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
In commit efa092f3d4 "[XFS] Fixes a bug in the quota code when
allocating a new dquot record", we allocate a new dquot block, grab a
buffer to initialize it, and return the locked initialized dquot buffer
to the caller for further in-core dquot initialization. Unfortunately,
if the _bmap_finish errored out, _qm_dqalloc would also error out
without bothering to free the (locked) buffer. Leaking a locked buffer
caused hangs in generic/388 when quotas are enabled.
Furthermore, the _bmap_finish -> _defer_finish conversion in
310a75a3c6 ("xfs: change xfs_bmap_{finish,cancel,init,free} ->
xfs_defer_*") failed to observe that the buffer was held going into
_defer_finish and therefore failed to notice that the buffer lock is
/not/ maintained afterwards. Now that we can bjoin a buffer to a
defer_ops, use this mechanism to ensure that the buffer stays locked
across the _defer_finish. Release the holds and locks on the buffer as
appropriate if we have to error out.
There is a subtlety here for the caller in that the buffer emerges
locked and held to the transaction, so if the _trans_commit fails we
have to release the buffer explicitly. This fixes the unmount hang
in generic/388 when quotas are enabled.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Unwritten extents by definition have not been written to until they
are converted to normal written extents. If unwritten extents are
freed from a file, it is therefore guaranteed that the blocks have
not been written to since allocation (note that zero range punches
and reallocates blocks).
To cut down on online discards generated from workloads that make
use of preallocation, skip discards of extents if they are in the
unwritten state when the extent is freed.
Note that this optimization does not apply to log recovery, during
which all freed extents are discarded if online discard is enabled.
Also note that it may be possible for a filesystem crash to occur
after write completion of an unwritten extent but before unwritten
conversion such that the extent remains unwritten after log
recovery. Since this pseudo-inconsistency may already be possible
after a crash (consider writing to recently allocated blocks where
the allocation transaction is lost after a crash), this change
shouldn't introduce any fundamental limitations that don't already
exist. In short, on storage stacks where discards are important,
it's good practice to run an occasional fstrim even with online
discard enabled in the filesystem, particularly after a crash.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
We've had reports of online discard operations being sent from XFS
on write-only workloads. These discards occur as a result of
eofblocks trims that can occur after a large file copy completes.
These discards are slightly confusing for users who might be paying
close attention to online discards (i.e., vdo) due to performance
sensitivity. They also happen to be spurious because freed post-eof
blocks by definition have not been written to during the current
allocation cycle.
Update xfs_free_eofblocks() to skip discards that are purely
attributed to eofblocks trims. This cuts down the number of spurious
discards that may occur on write-only workloads due to normal
preallocation activity.
Note that discards of post-eof extents can still occur from other
codepaths that do not isolate handling of post-eof blocks from those
within eof. For example, file unlinks and truncates may still cause
discards for any file blocks affected by the operation.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Freed extents are unconditionally discarded when online discard is
enabled. Define XFS_BMAPI_NODISCARD to allow callers to bypass
discards when unnecessary. For example, this will be useful for
eofblocks trimming.
This patch does not change behavior.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
It's just a connector between a transaction and a log item. There's
a 1:1 relationship between a log item descriptor and a log item,
and a 1:1 relationship between a log item descriptor and a
transaction. Both relationships are created and terminated at the
same time, so why do we even have the descriptor?
Replace it with a specific list_head in the log item and a new
log item dirtied flag to replace the XFS_LID_DIRTY flag.
Signed-Off-By: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[darrick: fix up deferred agfl intent finish_item use of LID_DIRTY]
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Just to make sure the item isn't associated with another
transaction when we try to reuse it.
Signed-Off-By: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
xfs_reflink_clear_inode_flag double-joins an inode to a transaction,
which is not allowed. Fix that and document that the caller must have
already joined it.
Signed-Off-By: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
[darrick: edit out trace for nonexistent ASSERT]
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
xfs_reflink_cancel_cow_range joins an inode twice to the same
transaction. This is not allowed, so fix it and document that the
callers of xfs_reflink_cancel_cow_blocks() must have already joined the
inode to the permanent transaction passed in.
Signed-Off-By: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
[darrick: edited the commit log to remove trace for nonexistent ASSERT]
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
xfs_inactive_symlink_rmt() does something nasty - it joins an inode
into a transaction it is already joined to. This means the inode can
have multiple log item descriptors attached to the transaction for
it. This breaks teh 1:1 mapping that is supposed to exist
between the log item and log item descriptor.
This results in the log item being processed twice during
transaction commit and CIL formatting, and there are lots of other
potential issues tha arise from double processing of log items in
the transaction commit state machine.
In this case, the inode is already held by the rolling transaction
returned from xfs_defer_finish(), so there's no need to join it
again.
Signed-Off-By: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
