[ Upstream commit 7efd105c27 ]
Since devm_regmap_init_mmio_clk can fail, add return value checking.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5da6cbcd2f ]
When the driver is used with a subdevice that is disabled in the
kernel configuration, clang gets a little confused about the
control flow and fails to notice that n_subdevs is only
uninitialized when subdevs is NULL, and we check for that,
leading to a false-positive warning:
drivers/mfd/arizona-core.c:1423:19: error: variable 'n_subdevs' is uninitialized when used here
[-Werror,-Wuninitialized]
subdevs, n_subdevs, NULL, 0, NULL);
^~~~~~~~~
drivers/mfd/arizona-core.c:999:15: note: initialize the variable 'n_subdevs' to silence this warning
int n_subdevs, ret, i;
^
= 0
Ideally, we would rearrange the code to avoid all those early
initializations and have an explicit exit in each disabled case,
but it's much easier to chicken out and add one more initialization
here to shut up the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c176c6d7e9 ]
The logic for setting the of_node on devices created by mfd did not set
the fwnode pointer to match, which caused fwnode-based APIs to
malfunction on these devices since the fwnode pointer was null. Fix
this.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5aa3709c0a ]
MODULE_DEVICE_TABLE(of, <of_match_table>) should be called to complete DT
OF mathing mechanism and register it.
Before this patch:
modinfo ./drivers/mfd/madera.ko | grep alias
After this patch:
modinfo ./drivers/mfd/madera.ko | grep alias
alias: of:N*T*Ccirrus,wm1840C*
alias: of:N*T*Ccirrus,wm1840
alias: of:N*T*Ccirrus,cs47l91C*
alias: of:N*T*Ccirrus,cs47l91
alias: of:N*T*Ccirrus,cs47l90C*
alias: of:N*T*Ccirrus,cs47l90
alias: of:N*T*Ccirrus,cs47l85C*
alias: of:N*T*Ccirrus,cs47l85
alias: of:N*T*Ccirrus,cs47l35C*
alias: of:N*T*Ccirrus,cs47l35
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80e5302e4b ]
An impending change to enable HAVE_C_RECORDMCOUNT on powerpc leads to
warnings such as the following:
# modprobe kprobe_example
ftrace-powerpc: Not expected bl: opcode is 3c4c0001
WARNING: CPU: 0 PID: 227 at kernel/trace/ftrace.c:2001 ftrace_bug+0x90/0x318
Modules linked in:
CPU: 0 PID: 227 Comm: modprobe Not tainted 5.2.0-rc6-00678-g1c329100b942 #2
NIP: c000000000264318 LR: c00000000025d694 CTR: c000000000f5cd30
REGS: c000000001f2b7b0 TRAP: 0700 Not tainted (5.2.0-rc6-00678-g1c329100b942)
MSR: 900000010282b033 <SF,HV,VEC,VSX,EE,FP,ME,IR,DR,RI,LE,TM[E]> CR: 28228222 XER: 00000000
CFAR: c0000000002642fc IRQMASK: 0
<snip>
NIP [c000000000264318] ftrace_bug+0x90/0x318
LR [c00000000025d694] ftrace_process_locs+0x4f4/0x5e0
Call Trace:
[c000000001f2ba40] [0000000000000004] 0x4 (unreliable)
[c000000001f2bad0] [c00000000025d694] ftrace_process_locs+0x4f4/0x5e0
[c000000001f2bb90] [c00000000020ff10] load_module+0x25b0/0x30c0
[c000000001f2bd00] [c000000000210cb0] sys_finit_module+0xc0/0x130
[c000000001f2be20] [c00000000000bda4] system_call+0x5c/0x70
Instruction dump:
419e0018 2f83ffff 419e00bc 2f83ffea 409e00cc 4800001c 0fe00000 3c62ff96
39000001 39400000 386386d0 480000c4 <0fe00000> 3ce20003 39000001 3c62ff96
---[ end trace 4c438d5cebf78381 ]---
ftrace failed to modify
[<c0080000012a0008>] 0xc0080000012a0008
actual: 01:00:4c:3c
Initializing ftrace call sites
ftrace record flags: 2000000
(0)
expected tramp: c00000000006af4c
Looking at the relocation records in __mcount_loc shows a few spurious
entries:
RELOCATION RECORDS FOR [__mcount_loc]:
OFFSET TYPE VALUE
0000000000000000 R_PPC64_ADDR64 .text.unlikely+0x0000000000000008
0000000000000008 R_PPC64_ADDR64 .text.unlikely+0x0000000000000014
0000000000000010 R_PPC64_ADDR64 .text.unlikely+0x0000000000000060
0000000000000018 R_PPC64_ADDR64 .text.unlikely+0x00000000000000b4
0000000000000020 R_PPC64_ADDR64 .init.text+0x0000000000000008
0000000000000028 R_PPC64_ADDR64 .init.text+0x0000000000000014
The first entry in each section is incorrect. Looking at the
relocation records, the spurious entries correspond to the
R_PPC64_ENTRY records:
RELOCATION RECORDS FOR [.text.unlikely]:
OFFSET TYPE VALUE
0000000000000000 R_PPC64_REL64 .TOC.-0x0000000000000008
0000000000000008 R_PPC64_ENTRY *ABS*
0000000000000014 R_PPC64_REL24 _mcount
<snip>
The problem is that we are not validating the return value from
get_mcountsym() in sift_rel_mcount(). With this entry, mcountsym is 0,
but Elf_r_sym(relp) also ends up being 0. Fix this by ensuring
mcountsym is valid before processing the entry.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Tested-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aaf06665f7 ]
Commit ed49f7fd64 ("powerpc/xmon: Disable tracing when entering
xmon") added code to disable recording trace entries while in xmon. The
commit introduced a variable 'tracing_enabled' to record if tracing was
enabled on xmon entry, and used this to conditionally enable tracing
during exit from xmon.
However, we are not checking the value of 'fromipi' variable in
xmon_core() when setting 'tracing_enabled'. Due to this, when secondary
cpus enter xmon, they will see tracing as being disabled already and
tracing won't be re-enabled on exit. Fix the same.
Fixes: ed49f7fd64 ("powerpc/xmon: Disable tracing when entering xmon")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04db3ede40 ]
The powerpc's flush_cache_vmap() is defined as a macro and never use
both of its arguments, so it will generate a compilation warning,
lib/ioremap.c: In function 'ioremap_page_range':
lib/ioremap.c:203:16: warning: variable 'start' set but not used
[-Wunused-but-set-variable]
Fix it by making it an inline function.
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 208a68c839 ]
On some machines, iio-sensor-proxy was returning all 0's for IIO sensor
values. It turns out that the bits_used for this sensor is 32, which makes
the mask calculation:
*mask = (1 << 32) - 1;
If the compiler interprets the 1 literals as 32-bit ints, it generates
undefined behavior depending on compiler version and optimization level.
On my system, it optimizes out the shift, so the mask value becomes
*mask = (1) - 1;
With a mask value of 0, iio-sensor-proxy will always return 0 for every axis.
Avoid incorrect 0 values caused by compiler optimization.
See original fix by Brett Dutro <brett.dutro@gmail.com> in
iio-sensor-proxy:
9615ceac7c
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 181fa434d0 ]
According to the PCI Local Bus specification Revision 3.0,
section 6.8.1.3 (Message Control for MSI), endpoints that
are Multiple Message Capable as defined by bits [3:1] in
the Message Control for MSI can request a number of vectors
that is power of two aligned.
As specified in section 6.8.1.6 "Message data for MSI", the Multiple
Message Enable field (bits [6:4] of the Message Control register)
defines the number of low order message data bits the function is
permitted to modify to generate its system software allocated
vectors.
The MSI controller in the Xilinx NWL PCIe controller supports a number
of MSI vectors specified through a bitmap and the hwirq number for an
MSI, that is the value written in the MSI data TLP is determined by
the bitmap allocation.
For instance, in a situation where two endpoints sitting on
the PCI bus request the following MSI configuration, with
the current PCI Xilinx bitmap allocation code (that does not
align MSI vector allocation on a power of two boundary):
Endpoint #1: Requesting 1 MSI vector - allocated bitmap bits 0
Endpoint #2: Requesting 2 MSI vectors - allocated bitmap bits [1,2]
The bitmap value(s) corresponds to the hwirq number that is programmed
into the Message Data for MSI field in the endpoint MSI capability
and is detected by the root complex to fire the corresponding
MSI irqs. The value written in Message Data for MSI field corresponds
to the first bit allocated in the bitmap for Multi MSI vectors.
The current Xilinx NWL MSI allocation code allows a bitmap allocation
that is not a power of two boundaries, so endpoint #2, is allowed to
toggle Message Data bit[0] to differentiate between its two vectors
(meaning that the MSI data will be respectively 0x0 and 0x1 for the two
vectors allocated to endpoint #2).
This clearly aliases with the Endpoint #1 vector allocation, resulting
in a broken Multi MSI implementation.
Update the code to allocate MSI bitmap ranges with a power of two
alignment, fixing the bug.
Fixes: ab597d35ef ("PCI: xilinx-nwl: Add support for Xilinx NWL PCIe Host Controller")
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a222061b85 ]
__uint128_t crops up in a few files that export symbols to modules, so
teach genksyms about it and the other GCC built-in 128-bit integer types
so that we don't end up skipping the CRC generation for some symbols due
to the parser failing to spot them:
| WARNING: EXPORT symbol "kernel_neon_begin" [vmlinux] version
| generation failed, symbol will not be versioned.
| ld: arch/arm64/kernel/fpsimd.o: relocation R_AARCH64_ABS32 against
| `__crc_kernel_neon_begin' can not be used when making a shared
| object
| ld: arch/arm64/kernel/fpsimd.o:(.data+0x0): dangerous relocation:
| unsupported relocation
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 589834b3a0 ]
In commit ebcc5928c5 ("arm64: Silence gcc warnings about arch ABI
drift"), the arm64 Makefile added -Wno-psabi to KBUILD_CFLAGS, which is
a GCC only option so clang rightfully complains:
warning: unknown warning option '-Wno-psabi' [-Wunknown-warning-option]
https://clang.llvm.org/docs/DiagnosticsReference.html#wunknown-warning-option
However, by default, this is merely a warning so the build happily goes
on with a slew of these warnings in the process.
Commit c3f0d0bc5b ("kbuild, LLVMLinux: Add -Werror to cc-option to
support clang") worked around this behavior in cc-option by adding
-Werror so that unknown flags cause an error. However, this all happens
silently and when an unknown flag is added to the build unconditionally
like -Wno-psabi, cc-option will always fail because there is always an
unknown flag in the list of flags. This manifested as link time failures
in the arm64 libstub because -fno-stack-protector didn't get added to
KBUILD_CFLAGS.
To avoid these weird cryptic failures in the future, make clang behave
like gcc and immediately error when it encounters an unknown flag by
adding -Werror=unknown-warning-option to CLANG_FLAGS. This can be added
unconditionally for clang because it is supported by at least 3.0.0,
according to godbolt [1] and 4.0.0, according to its documentation [2],
which is far earlier than we typically support.
[1]: https://godbolt.org/z/7F7rm3
[2]: https://releases.llvm.org/4.0.0/tools/clang/docs/DiagnosticsReference.html#wunknown-warning-option
Link: https://github.com/ClangBuiltLinux/linux/issues/511
Link: https://github.com/ClangBuiltLinux/linux/issues/517
Suggested-by: Peter Smith <peter.smith@linaro.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79b4499524 ]
During probe, return the "get_irq" error value instead of -EINVAL which
allows the driver to be deferred probed if needed.
Fix also the case where of_irq_get() returns a negative value.
Note :
On failure of_irq_get() returns 0 or a negative value while
platform_get_irq() returns a negative value.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc6b698a86 ]
With CONFIG_PROVE_LOCKING=y, using sysfs to remove a bridge with a device
below it causes a lockdep warning, e.g.,
# echo 1 > /sys/class/pci_bus/0000:00/device/0000:00:00.0/remove
============================================
WARNING: possible recursive locking detected
...
pci_bus 0000:01: busn_res: [bus 01] is released
The remove recursively removes the subtree below the bridge. Each call
uses a different lock so there's no deadlock, but the locks were all
created with the same lockdep key so the lockdep checker can't tell them
apart.
Mark the "remove" sysfs attribute with __ATTR_IGNORE_LOCKDEP() as it is
safe to ignore the lockdep check between different "remove" kernfs
instances.
There's discussion about a similar issue in USB at [1], which resulted in
356c05d58a ("sysfs: get rid of some lockdep false positives") and
e9b526fe70 ("i2c: suppress lockdep warning on delete_device"), which do
basically the same thing for USB "remove" and i2c "delete_device" files.
[1] https://lore.kernel.org/r/Pine.LNX.4.44L0.1204251436140.1206-100000@iolanthe.rowland.org
Link: https://lore.kernel.org/r/20190526225151.3865-1-marek.vasut@gmail.com
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
[bhelgaas: trim commit log, details at above links]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d99482673f ]
This patch adds a check for the GPIOs property existence, before the
GPIO is requested. This fixes an issue seen when the 8250 mctrl_gpio
support is added (2nd patch in this patch series) on x86 platforms using
ACPI.
Here Mika's comments from 2016-08-09:
"
I noticed that with v4.8-rc1 serial console of some of our Broxton
systems does not work properly anymore. I'm able to see output but input
does not work.
I bisected it down to commit 4ef03d3287
("tty/serial/8250: use mctrl_gpio helpers").
The reason why it fails is that in ACPI we do not have names for GPIOs
(except when _DSD is used) so we use the "idx" to index into _CRS GPIO
resources. Now mctrl_gpio_init_noauto() goes through a list of GPIOs
calling devm_gpiod_get_index_optional() passing "idx" of 0 for each. The
UART device in Broxton has following (simplified) ACPI description:
Device (URT4)
{
...
Name (_CRS, ResourceTemplate () {
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO0", 0x00, ResourceConsumer)
{
0x003A
}
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO0", 0x00, ResourceConsumer)
{
0x003D
}
})
In this case it finds the first GPIO (0x003A which happens to be RX pin
for that UART), turns it into GPIO which then breaks input for the UART
device. This also breaks systems with bluetooth connected to UART (those
typically have some GPIOs in their _CRS).
Any ideas how to fix this?
We cannot just drop the _CRS index lookup fallback because that would
break many existing machines out there so maybe we can limit this to
only DT enabled machines. Or alternatively probe if the property first
exists before trying to acquire the GPIOs (using
device_property_present()).
"
This patch implements the fix suggested by Mika in his statement above.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4368a1539c ]
add_display_components() calls of_platform_populate, and we depopluate
on pdev remove, but not when probe fails. So if we get a probe deferral
in one of the components, we won't depopulate the platform. This causes
the core to keep references to devices which should be destroyed, which
causes issues when those same devices try to re-initialize on the next
probe attempt.
I think this is the reason we had issues with the gmu's device-managed
resources on deferral (worked around in commit 94e3a17f33a5).
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617201301.133275-3-sean@poorly.run
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df5be5be87 ]
When the firmware does PCI BAR resource allocation, it passes the assigned
addresses and flags (prefetch/64bit/...) via the "reg" property of
a PCI device device tree node so the kernel does not need to do
resource allocation.
The flags are stored in resource::flags - the lower byte stores
PCI_BASE_ADDRESS_SPACE/etc bits and the other bytes are IORESOURCE_IO/etc.
Some flags from PCI_BASE_ADDRESS_xxx and IORESOURCE_xxx are duplicated,
such as PCI_BASE_ADDRESS_MEM_PREFETCH/PCI_BASE_ADDRESS_MEM_TYPE_64/etc.
When parsing the "reg" property, we copy the prefetch flag but we skip
on PCI_BASE_ADDRESS_MEM_TYPE_64 which leaves the flags out of sync.
The missing IORESOURCE_MEM_64 flag comes into play under 2 conditions:
1. we remove PCI_PROBE_ONLY for pseries (by hacking pSeries_setup_arch()
or by passing "/chosen/linux,pci-probe-only");
2. we request resource alignment (by passing pci=resource_alignment=
via the kernel cmd line to request PAGE_SIZE alignment or defining
ppc_md.pcibios_default_alignment which returns anything but 0). Note that
the alignment requests are ignored if PCI_PROBE_ONLY is enabled.
With 1) and 2), the generic PCI code in the kernel unconditionally
decides to:
- reassign the BARs in pci_specified_resource_alignment() (works fine)
- write new BARs to the device - this fails for 64bit BARs as the generic
code looks at IORESOURCE_MEM_64 (not set) and writes only lower 32bits
of the BAR and leaves the upper 32bit unmodified which breaks BAR mapping
in the hypervisor.
This fixes the issue by copying the flag. This is useful if we want to
enforce certain BAR alignment per platform as handling subpage sized BARs
is proven to cause problems with hotplug (SLOF already aligns BARs to 64k).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Reviewed-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Shawn Anastasio <shawn@anastas.io>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de23f0b757 ]
The O2 controller supports 8-bit EMMC access.
JESD84-B51 section A.6.3.a defines the bus testing procedure that
`mmc_select_bus_width()` implements. This is used to determine the actual
bus width of the eMMC.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 508595515f ]
In some cases the "Allocate & copy" block in ffs_epfile_io() is not
executed. Consequently, in such a case ffs_alloc_buffer() is never called
and struct ffs_io_data is not initialized properly. This in turn leads to
problems when ffs_free_buffer() is called at the end of ffs_epfile_io().
This patch uses kzalloc() instead of kmalloc() in the aio case and memset()
in non-aio case to properly initialize struct ffs_io_data.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13b18d3590 ]
A bug was introduced by commit b3b5764618 ("tty: serial_core: convert
uart_open to use tty_port_open"). It caused a constant warning printed
into the system log regarding the tty and port counter mismatch:
[ 21.644197] ttyS ttySx: tty_port_close_start: tty->count = 1 port count = 2
in case if session hangup was detected so the warning is printed starting
from the second open-close iteration.
Particularly the problem was discovered in situation when there is a
serial tty device without hardware back-end being setup. It is considered
by the tty-serial subsystems as a hardware problem with session hang up.
In this case uart_startup() will return a positive value with TTY_IO_ERROR
flag set in corresponding tty_struct instance. The same value will get
passed to be returned from the activate() callback and then being returned
from tty_port_open(). But since in this case tty_port_block_til_ready()
isn't called the TTY_PORT_ACTIVE flag isn't set (while the method had been
called before tty_port_open conversion was introduced and the rest of the
subsystem code expected the bit being set in this case), which prevents the
uart_hangup() method to perform any cleanups including the tty port
counter setting to zero. So the next attempt to open/close the tty device
will discover the counters mismatch.
In order to fix the problem we need to manually set the TTY_PORT_ACTIVE
flag in case if uart_startup() returned a positive value. In this case
the hang up procedure will perform a full set of cleanup actions including
the port ref-counter resetting.
Fixes: b3b5764618 "tty: serial_core: convert uart_open to use tty_port_open"
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e828c3e09 ]
imx_uart_set_termios() called imx_uart_rts_active(), or
imx_uart_rts_inactive() before taking port->port.lock.
As a consequence, sport->port.mctrl that these functions modify
could have been changed without holding port->port.lock.
Moved locking of port->port.lock above the calls to fix the issue.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99b9683f21 ]
When fixing up the clock in vop_crtc_mode_fixup() we're not doing it
quite correctly. Specifically if we've got the true clock 266666667 Hz,
we'll perform this calculation:
266666667 / 1000 => 266666
Later when we try to set the clock we'll do clk_set_rate(266666 *
1000). The common clock framework won't actually pick the proper clock
in this case since it always wants clocks <= the specified one.
Let's solve this by using DIV_ROUND_UP.
Fixes: b59b8de314 ("drm/rockchip: return a true clock rate to adjusted_mode")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20190614224730.98622-1-dianders@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e59a175faa ]
CPU online/offline code paths are sensitive to parts of the device
tree (various cpu node properties, cache nodes) that can be changed as
a result of a migration.
Prevent CPU hotplug while the device tree potentially is inconsistent.
Fixes: 410bccf978 ("powerpc/pseries: Partition migration in the kernel")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4a36e8292 ]
This patch fixes memory leak at error paths of the probe function.
In for_each_child_of_node, if the loop returns, the driver should
call of_put_node() before returns.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Fixes: 1233f59f74 ("phy: Renesas R-Car Gen2 PHY driver")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ff3a5c88e ]
After data is copied to the cache entry, atomic_set is used indicate
that the data is the entry is valid without appropriate memory barriers.
Similarly the read side was missing the corresponding memory barriers.
Signed-off-by: David Riley <davidriley@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20190610211810.253227-5-davidriley@chromium.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f04bee34d6 ]
[Why]
Unlike our regular connectors, MST connectors don't start off with
an initial connector state. This causes a NULL pointer dereference to
occur when attaching the bpc property since it tries to modify the
connector state.
We need an initial connector state on the connector to avoid the crash.
[How]
Use our reset helper to allocate an initial state and reset the values
to their defaults. We were already doing this before, just not for
MST connectors.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db1b5bc047 ]
Interrupt handler checked THRE bit (transmitter holding register
empty) in LSR to detect if TX fifo is empty.
In case when there is only receive interrupts the TX handling
got called because THRE bit in LSR is set when there is no
transmission (FIFO empty). TX handling caused TX stop, which in
RS-485 half-duplex mode actually resets receiver FIFO. This is not
desired during reception because of possible data loss.
The fix is to check if THRI is set in IER in addition of the TX
fifo status. THRI in IER is set when TX is started and cleared
when TX is stopped.
This ensures that TX handling is only called when there is really
transmission on going and an interrupt for THRE and not when there
are only RX interrupts.
Signed-off-by: Kimmo Rautkoski <ext-kimmo.rautkoski@vaisala.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba3684f99f ]
The function msm_wait_for_xmitr can be taken with interrupts
disabled. In order to avoid a potential system lockup - demonstrated
under stress testing conditions on SoC QCS404/5 - make sure we wait
for a bounded amount of time.
Tested on SoC QCS404.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65f1a0d39c ]
If bus_register fails. On its error handling path, it has cleaned up
what it has done. There is no need to call bus_unregister again.
Otherwise, if bus_unregister is called, issues such as null-ptr-deref
will arise.
Syzkaller report this:
kobject_add_internal failed for memstick (error: -12 parent: bus)
BUG: KASAN: null-ptr-deref in sysfs_remove_file_ns+0x1b/0x40 fs/sysfs/file.c:467
Read of size 8 at addr 0000000000000078 by task syz-executor.0/4460
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xa9/0x10e lib/dump_stack.c:113
__kasan_report+0x171/0x18d mm/kasan/report.c:321
kasan_report+0xe/0x20 mm/kasan/common.c:614
sysfs_remove_file_ns+0x1b/0x40 fs/sysfs/file.c:467
sysfs_remove_file include/linux/sysfs.h:519 [inline]
bus_remove_file+0x6c/0x90 drivers/base/bus.c:145
remove_probe_files drivers/base/bus.c:599 [inline]
bus_unregister+0x6e/0x100 drivers/base/bus.c:916 ? 0xffffffffc1590000
memstick_init+0x7a/0x1000 [memstick]
do_one_initcall+0xb9/0x3b5 init/main.c:914
do_init_module+0xe0/0x330 kernel/module.c:3468
load_module+0x38eb/0x4270 kernel/module.c:3819
__do_sys_finit_module+0x162/0x190 kernel/module.c:3909
do_syscall_64+0x72/0x2a0 arch/x86/entry/common.c:298
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: baf8532a14 ("memstick: initial commit for Sony MemoryStick support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai26@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d99004d720 ]
I. was. blind.
Caught with vkms, which has some really slow crc computation function.
Fixes: 1882018a70 ("drm/crc-debugfs: User irqsafe spinlock in drm_crtc_add_crc_entry")
Cc: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Emil Velikov <emil.velikov@collabora.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190606211544.5389-1-daniel.vetter@ffwll.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1882018a70 ]
We can be called from any context, we need to be prepared.
Noticed this while hacking on vkms, which calls this function from a
normal worker. Which really upsets lockdep.
Cc: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Emil Velikov <emil.velikov@collabora.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190605194556.16744-1-daniel.vetter@ffwll.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e390478cf ]
Recent versions of the DMA API debug code have started to warn about
violations of the maximum DMA segment size. This is because the segment
size defaults to 64 KiB, which can easily be exceeded in large buffer
allocations such as used in DRM/KMS for framebuffers.
Technically the Tegra SMMU and ARM SMMU don't have a maximum segment
size (they map individual pages irrespective of whether they are
contiguous or not), so the choice of 4 MiB is a bit arbitrary here. The
maximum segment size is a 32-bit unsigned integer, though, so we can't
set it to the correct maximum size, which would be the size of the
aperture.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8dbfc5b650 ]
The pixel clock unit in the first two registers (0x00 and 0x01) of
sii9022 is 10kHz, not 1kHz as in struct drm_display_mode. Division by
10 fixes the issue.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1a2a8eae0b9d6333e7a5841026bf7fd65c9ccd09.1558964241.git.jsarha@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3231573065 ]
We need to know the link bandwidth to filter out modes we cannot
support, so we need to have read the display props before doing the
filtering.
To ensure we have up to date display props, call tc_get_display_props()
in the beginning of tc_connector_get_modes().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-22-tomi.valkeinen@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76002d8b48 ]
Commit 0e7df22401 ("PCI: Add sysfs sriov_drivers_autoprobe to control
VF driver binding") allows the user to specify that drivers for VFs of
a PF should not be probed, but it actually causes pci_device_probe() to
return success back to the driver core in this case. Therefore by all
sysfs appearances the device is bound to a driver, the driver link from
the device exists as does the device link back from the driver, yet the
driver's probe function is never called on the device. We also fail to
do any sort of cleanup when we're prohibited from probing the device,
the IRQ setup remains in place and we even hold a device reference.
Instead, abort with errno before any setup or references are taken when
pci_device_can_probe() prevents us from trying to probe the device.
Link: https://lore.kernel.org/lkml/155672991496.20698.4279330795743262888.stgit@gimli.home
Fixes: 0e7df22401 ("PCI: Add sysfs sriov_drivers_autoprobe to control VF driver binding")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f1f1a2dab ]
In drm_load_edid_firmware(), fwstr is allocated by kstrdup(). And fwstr
is dereferenced in the following codes. However, memory allocation
functions such as kstrdup() may fail and returns NULL. Dereferencing
this null pointer may cause the kernel go wrong. Thus we should check
this kstrdup() operation.
Further, if kstrdup() returns NULL, we should return ERR_PTR(-ENOMEM) to
the caller site.
Signed-off-by: Gen Zhang <blackgod016574@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190524023222.GA5302@zhanggen-UX430UQ
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 065e4bdfa1 ]
Previous codes assumes there are two sdma engines.
This is not true e.g., Raven only has 1 SDMA engine.
Fix the issue by using sdma engine number info in
device_info.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1090d58d48 ]
[Why]
When disable driver, OS will set backlight optimization
then do stop device. But this flag will cause driver to
enable ABM when driver disabled.
[How]
Send ABM disable command before destroy ABM construct
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe2b5323d2 ]
it requires to initialize HDP_NONSURFACE_BASE, so as to avoid
using the value left by a previous VM under sriov scenario.
v2: it should not hurt baremetal, generalize it for both sriov
and baremetal
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Tiecheng Zhou <Tiecheng.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1352c779cb ]
[Why]
An assertion is thrown when using SURFACE_PIXEL_FORMAT_GRPH_RGB565
formats on DCE since the prescale_params->scale wasn't being filled.
Found by a dmesg-fail when running the
igt@kms_plane@pixel-format-pipe-a-planes test on Baffin.
[How]
Fill in the scale parameter.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06aaa3d066 ]
SMC relocation can also be activated earlier by the bootloader,
so the driver's behaviour cannot rely on selected kernel config.
When the SMC is relocated, CPM_CR_INIT_TRX cannot be used.
But the only thing CPM_CR_INIT_TRX does is to clear the
rstate and tstate registers, so this can be done manually,
even when SMC is not relocated.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 9ab9212014 ("cpm_uart: fix non-console port startup bug")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c89c70634 ]
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/pinctrl-rockchip.c:3221:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3196, but without a corresponding object release within this function.
./drivers/pinctrl/pinctrl-rockchip.c:3223:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3196, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-gpio@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35240ba26a ]
Current calculator doesn't do it' job quite correct. First of all the
max310x baud-rates generator supports the divisor being less than 16.
In this case the x2/x4 modes can be used to double or quadruple
the reference frequency. But the current baud-rate setter function
just filters all these modes out by the first condition and setups
these modes only if there is a clocks-baud division remainder. The former
doesn't seem right at all, since enabling the x2/x4 modes causes the line
noise tolerance reduction and should be only used as a last resort to
enable a requested too high baud-rate.
Finally the fraction is supposed to be calculated from D = Fref/(c*baud)
formulae, but not from D % 16, which causes the precision loss. So to speak
the current baud-rate calculator code works well only if the baud perfectly
fits to the uart reference input frequency.
Lets fix the calculator by implementing the algo fully compliant with
the fractional baud-rate generator described in the datasheet:
D = Fref / (c*baud), where c={16,8,4} is the x1/x2/x4 rate mode
respectively, Fref - reference input frequency. The divisor fraction is
calculated from the same formulae, but making sure it is found with a
resolution of 0.0625 (four bits).
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5617592927 ]
If the device rejects the control transfer to enable device-initiated
U1/U2 entry, then the device will not initiate U1/U2 transition. To
improve the performance, the downstream port should not initate
transition to U1/U2 to avoid the delay from the device link command
response (no packet can be transmitted while waiting for a response from
the device). If the device has some quirks and does not implement U1/U2,
it may reject all the link state change requests, and the downstream
port may resend and flood the bus with more requests. This will affect
the device performance even further. This patch disables the
hub-initated U1/U2 if the device-initiated U1/U2 entry fails.
Reference: USB 3.2 spec 7.2.4.2.3
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8c2869300 ]
Check on called function's returned value for error and return 0 on
success or a negative errno value on error instead of a boolean value.
Signed-off-by: Quentin Deslandes <quentin.deslandes@itdev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
