[ Upstream commit 69e168ebdc ]
NFP shift instruction has something special. If shift direction is left
then shift amount of 1 to 31 is specified as 32 minus the amount to shift.
But no need to do this for indirect shift which has shift amount be 0. Even
after we do this subtraction, shift amount 0 will be turned into 32 which
will eventually be encoded the same as 0 because only low 5 bits are
encoded, but shift amount be 32 will fail the FIELD_PREP check done later
on shift mask (0x1f), due to 32 is out of mask range. Such error has been
observed when compiling nfp/bpf/jit.c using gcc 8.3 + O3.
This issue has started when indirect shift support added after which the
incoming shift amount to __emit_shf could be 0, therefore it is at that
time shift amount adjustment inside __emit_shf should have been tightened.
Fixes: 991f5b3651 ("nfp: bpf: support logic indirect shifts (BPF_[L|R]SH | BPF_X)")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Pablo Cascón <pablo.cascon@netronome.com
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63a0666bca ]
Fix lack of keyboard interrupts for RiscPC due to incorrect conversion.
Fixes: e8d36d5dbb ("ARM: kill off set_irq_flags usage")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a279345807 ]
There is an abnormally low about 20ms,when setting duty repeatedly.
Because setting the duty will disable PWM and then enable. Delete
this operation now.
Fixes: 211ed63075 ("pwm: Add support for Meson PWM Controller")
Signed-off-by: Bichao Zheng <bichao.zheng@amlogic.com>
[ Dropped code instead of hiding it behind a comment ]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51496e4446 ]
The pre-divider allows configuring longer PWM periods compared to using
the input clock directly. The pre-divider is 7 bit wide, meaning it's
maximum value is 128 (the register value is off-by-one: 0x7f or 127).
Change the loop to also allow for the maximum possible value to be
considered valid.
Fixes: 211ed63075 ("pwm: Add support for Meson PWM Controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 680f6af533 ]
If userspace provides a rule blob with trailing data after last target,
we trigger a splat, then convert ruleset to 64bit format (with trailing
data), then pass that to do_replace_finish() which then returns -EINVAL.
Erroring out right away avoids the splat plus unneeded translation and
error unwind.
Fixes: 81e675c227 ("netfilter: ebtables: add CONFIG_COMPAT support")
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d1f8b3d75 ]
The "out_data" variable is uninitialized at the point. Originally, this
used to print "status" instead and that seems like the correct thing to
print.
Fixes: bc2ef88432 ("alienware-wmi: For WMAX HDMI method, introduce a way to query HDMI cable status")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b72845ee55 ]
In vpbe_enum_outputs() we check if (temp_index >= cfg->num_outputs) but
the problem is that "temp_index" can be negative. This patch changes
the types to unsigned to address this array underflow bug.
Fixes: 66715cdc32 ("[media] davinci vpbe: VPBE display driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd6e2a981b ]
The "b->index" is a u32 the comes from the user in the ioctl. It hasn't
been checked. We aren't supposed to use it but we're instead supposed
to use the value that gets written to it when we call videobuf_dqbuf().
The videobuf_dqbuf() first memsets it to zero and then re-initializes it
inside the videobuf_status() function. It's this final value which we
want.
Hans Verkuil pointed out that we need to check the return from
videobuf_dqbuf(). I ended up doing a little cleanup related to that as
well.
Fixes: 72915e851d ("[media] V4L2: OMAP: VOUT: dma map and unmap v4l2 buffers in qbuf and dqbuf")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 534420c6ff ]
The build of aica sound driver has been broken since the timer API
conversion and some code rewrite. This patch fixes the breakage by
using the common substream field, as well as a bit cleaning up wrt the
timer handling in the code.
Fixes: d522bb6a10 ("ALSA: sh: aica: Convert timers to use timer_setup()")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6093e348a5 ]
device_for_each_child() stops executing callback function for remaining
child devices, if callback hits an error.
Each child mdev device is independent of each other.
While unregistering parent device, mdev core must remove all child mdev
devices.
Therefore, mdev_device_remove_cb() always returns success so that
device_for_each_child doesn't abort if one child removal hits error.
While at it, improve remove and unregister functions for below simplicity.
There isn't need to pass forced flag pointer during mdev parent
removal which invokes mdev_device_remove(). So simplify the flow.
mdev_device_remove() is called from two paths.
1. mdev_unregister_driver()
mdev_device_remove_cb()
mdev_device_remove()
2. remove_store()
mdev_device_remove()
Fixes: 7b96953bc6 ("vfio: Mediated device Core driver")
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6d6f4f160 ]
mdev_remove_sysfs_files() should follow exact mirror sequence of a
create, similar to what is followed in error unwinding path of
mdev_create_sysfs_files().
Fixes: 6a62c1dfb5 ("vfio/mdev: Re-order sysfs attribute creation")
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60e7f2c3fe ]
During mdev parent registration in mdev_register_device(),
if parent device is duplicate, it releases the reference of existing
parent device.
This is incorrect. Existing parent device should not be touched.
Fixes: 7b96953bc6 ("vfio: Mediated device Core driver")
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c73aa4102f ]
Fix the ->get handlers for the afs.cell and afs.volume xattrs to pass the
source data size to memcpy() rather than target buffer size.
Overcopying the source data occasionally causes the kernel to oops.
Fixes: d3e3b7eac8 ("afs: Add metadata xattrs")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42f1bc43e6 ]
Currently the protected management frames are
not appended with the MIC_LEN which results in
the protected management frames being encoded
incorrectly.
Add the extra space at the end of the protected
management frames to fix this encoding error for
the protected management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: 1807da4973 ("ath10k: wmi: add management tx by reference support over wmi")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e1943af29 ]
In the function mmc_alloc_host, the function put_device is called to
release allocated resources when mmc_gpio_alloc fails. Finally, the
function pointed by host->class_dev.class->dev_release (i.e.,
mmc_host_classdev_release) is used to release resources including the
host structure. However, after put_device, host is used and released
again. Resulting in a use-after-free bug.
Fixes: 1ed2171944 ("mmc: core: fix error path in mmc_host_alloc")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8dd29f1951 ]
The driver registers the watchdog with devm_watchdog_register_device() but
still calls watchdog_unregister_device() on remove. Since clocks have to
be stopped when removing the driver, after the watchdog device has been
unregistered, we can not drop the call to watchdog_unregister_device().
Use watchdog_register_device() to register the watchdog.
Fixes: 2bdf6acbfe ("watchdog: Add Realtek RTD1295")
Cc: Andreas Färber <afaerber@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f33e7bb3eb ]
Status of ADMA channel registers is not saved and restored during system
suspend. During active playback if system enters suspend, this results in
wrong state of channel registers during system resume and playback fails
to resume properly. Fix this by saving following channel registers in
runtime suspend and restore during runtime resume.
* ADMA_CH_LOWER_SRC_ADDR
* ADMA_CH_LOWER_TRG_ADDR
* ADMA_CH_FIFO_CTRL
* ADMA_CH_CONFIG
* ADMA_CH_CTRL
* ADMA_CH_CMD
* ADMA_CH_TC
Runtime PM calls will be inovked during system resume path if a playback
or capture needs to be resumed. Hence above changes work fine for system
suspend case.
Fixes: f46b195799 ("dmaengine: tegra-adma: Add support for Tegra210 ADMA")
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3cfe7ddbc ]
ena_com_set_hash_function() tests if a hash function is supported
by the device before setting it.
The test returns the opposite result than needed.
Reverse the condition to return the correct value.
Also use the BIT macro instead of inline shift.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b287cdbd1c ]
ena_up() calls ena_init_napi() but does not call ena_del_napi() in
case of failure. This causes a segmentation fault upon rmmod when
netif_napi_del() is called. Fix this bug by calling ena_del_napi()
before returning error from ena_up().
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c6eeff295 ]
second parameter should be the index of the table rather than the value.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Saeed Bshara <saeedb@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5daab58043 ]
The kernel parameter igfx_off is used by users to disable
DMA remapping for the Intel integrated graphic device. It
was designed for bare metal cases where a dedicated IOMMU
is used for graphic. This doesn't apply to virtual IOMMU
case where an include-all IOMMU is used. This makes the
kernel parameter work with virtual IOMMU as well.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Suggested-by: Kevin Tian <kevin.tian@intel.com>
Fixes: c0771df8d5 ("intel-iommu: Export a flag indicating that the IOMMU is used for iGFX.")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bf3e2b881 ]
Always consider the skb reserve space based on netdevice of the GID
attribute, regardless of vlan or non vlan netdevice.
Fixes: 43c9fc509f ("rdma_rxe: make rxe work over 802.1q VLAN devices")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f4426aa19 ]
The QP transition optional parameters for the various transition for XRC
QPs are identical to those for RC QPs.
Many of the XRC QP transition optional parameter bits are missing from the
QP optional mask table. These omissions caused failures when doing XRC QP
state transitions.
For example, when trying to change the response timer of an XRC receive QP
via the RTS2RTS transition, the new timer value was ignored because
MLX5_QP_OPTPAR_RNR_TIMEOUT bit was missing from the optional params mask
for XRC qps for the RTS2RTS transition.
Fix this by adding the missing XRC optional parameters for all QP
transitions to the opt_mask table.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Fixes: a4774e9095 ("IB/mlx5: Fix opt param mask according to firmware spec")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5acb4b9701 ]
Fix calculation of transfer size on completion in function
dwc2_gadget_get_xfersize_ddma().
Added increment of descriptor pointer to move to next descriptor in
the loop.
Fixes: aa3e8bc813 ("usb: dwc2: gadget: DDMA transfer start and complete")
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2100e3ca36 ]
The dependency to ensure this driver links correctly fails since
it can not be a loadable module:
drivers/usb/phy/phy-fsl-usb.o: In function `fsl_otg_set_peripheral':
phy-fsl-usb.c:(.text+0x2224): undefined reference to `usb_gadget_vbus_disconnect'
Make the option 'tristate' so it can work correctly.
Fixes: 5a8d651a2b ("usb: gadget: move gadget API functions to udc-core")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a7c59c6d9 ]
A stream may specify a rate range using 'rate_min' and 'rate_max', so a
stream may be valid and not specify any rates. However, as stream cannot
be valid and not have any channel. Let's use this condition instead to
determine if a stream is valid or not.
Fixes: cde79035c6 ("ASoC: Handle multiple codecs with split playback / capture")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2cf86e156 ]
Packet send checks that msg_name is at least sizeof sockaddr_ll.
Packet recv must return at least this length, so that its output
can be passed unmodified to packet send.
This ceased to be true since adding support for lladdr longer than
sll_addr. Since, the return value uses true address length.
Always return at least sizeof sockaddr_ll, even if address length
is shorter. Zero the padding bytes.
Change v1->v2: do not overwrite zeroed padding again. use copy_len.
Fixes: 0fb375fb9b ("[AF_PACKET]: Allow for > 8 byte hardware addresses.")
Suggested-by: David Laight <David.Laight@aculab.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a38df676a ]
The card detect pin was incorrectly using IRQ_TYPE_LEVEL_LOW
instead of GPIO_ACTIVE_LOW when reading the state of the CD pin.
This was previosly fixed on Torpedo, but missed on the SOM-LV
Fixes: 5cb8b0fa55 ("ARM: dts: Move most of logicpd-som-lv-37xx-devkit.dts to logicpd-som-lv-baseboard.dtsi")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8cff995405 ]
iProc config read flag has to be enabled for PAXBv2 instead of PAXB.
Fixes: f78e60a29d ("PCI: iproc: Reject unconfigured physical functions from PAXC")
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 270a8a297f ]
This is fixing flow offload for UDP traffic where packets only follow
one single direction.
The flow_offload_fixup_tcp() mechanism works fine in case that the
offloaded entry remains in SYN_RECV state, given sequence tracking is
reset and that conntrack handles syn+ack packets as a retransmission, ie.
sES + synack => sIG
for reply traffic.
Fixes: a3c90f7a23 ("netfilter: nf_tables: flow offload expression")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3309bec85e ]
The trace_hardirqs_on() sets current->hardirqs_enabled and from here
the lockdep assumes interrupts are enabled although they are remain
disabled until the context switches to the guest. Consequent
srcu_read_lock() checks the flags in rcu_lock_acquire(), observes
disabled interrupts and prints a warning (see below).
This moves trace_hardirqs_on/off closer to __kvmppc_vcore_entry to
prevent lockdep from being confused.
DEBUG_LOCKS_WARN_ON(current->hardirqs_enabled)
WARNING: CPU: 16 PID: 8038 at kernel/locking/lockdep.c:4128 check_flags.part.25+0x224/0x280
[...]
NIP [c000000000185b84] check_flags.part.25+0x224/0x280
LR [c000000000185b80] check_flags.part.25+0x220/0x280
Call Trace:
[c000003fec253710] [c000000000185b80] check_flags.part.25+0x220/0x280 (unreliable)
[c000003fec253780] [c000000000187ea4] lock_acquire+0x94/0x260
[c000003fec253840] [c00800001a1e9768] kvmppc_run_core+0xa60/0x1ab0 [kvm_hv]
[c000003fec253a10] [c00800001a1ed944] kvmppc_vcpu_run_hv+0x73c/0xec0 [kvm_hv]
[c000003fec253ae0] [c00800001a1095dc] kvmppc_vcpu_run+0x34/0x48 [kvm]
[c000003fec253b00] [c00800001a1056bc] kvm_arch_vcpu_ioctl_run+0x2f4/0x400 [kvm]
[c000003fec253b90] [c00800001a0f3618] kvm_vcpu_ioctl+0x460/0x850 [kvm]
[c000003fec253d00] [c00000000041c4f4] do_vfs_ioctl+0xe4/0x930
[c000003fec253db0] [c00000000041ce04] ksys_ioctl+0xc4/0x110
[c000003fec253e00] [c00000000041ce78] sys_ioctl+0x28/0x80
[c000003fec253e20] [c00000000000b5a4] system_call+0x5c/0x70
Instruction dump:
419e0034 3d220004 39291730 81290000 2f890000 409e0020 3c82ffc6 3c62ffc5
3884be70 386329c0 4bf6ea71 60000000 <0fe00000> 3c62ffc6 3863be90 4801273d
irq event stamp: 1025
hardirqs last enabled at (1025): [<c00800001a1e9728>] kvmppc_run_core+0xa20/0x1ab0 [kvm_hv]
hardirqs last disabled at (1024): [<c00800001a1e9358>] kvmppc_run_core+0x650/0x1ab0 [kvm_hv]
softirqs last enabled at (0): [<c0000000000f1210>] copy_process.isra.4.part.5+0x5f0/0x1d00
softirqs last disabled at (0): [<0000000000000000>] (null)
---[ end trace 31180adcc848993e ]---
possible reason: unannotated irqs-off.
irq event stamp: 1025
hardirqs last enabled at (1025): [<c00800001a1e9728>] kvmppc_run_core+0xa20/0x1ab0 [kvm_hv]
hardirqs last disabled at (1024): [<c00800001a1e9358>] kvmppc_run_core+0x650/0x1ab0 [kvm_hv]
softirqs last enabled at (0): [<c0000000000f1210>] copy_process.isra.4.part.5+0x5f0/0x1d00
softirqs last disabled at (0): [<0000000000000000>] (null)
Fixes: 8b24e69fc4 ("KVM: PPC: Book3S HV: Close race with testing for signals on guest entry", 2017-06-26)
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a861b49273 ]
The "(&ctio->u.status1.sense_data)[i]" where i >= 0 expressions in
qlt_send_resp_ctio() are probably typos and should have been
"(&ctio->u.status1.sense_data[4 * i])" instead. Instead of only fixing
these typos, modify the code for storing sense data such that it becomes
easy to read. This patch fixes a Coverity complaint about accessing an
array outside its bounds.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Fixes: be25152c0d ("qla2xxx: Improve T10-DIF/PI handling in driver.") # v4.11.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c04466c171 ]
The test "if (!cmd)" is not useful because it is guaranteed that cmd !=
NULL. Instead of testing the cmd pointer, rely on the tag to decide
whether or not command allocation failed.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Fixes: 33e7997755 ("qla2xxx: Add support for QFull throttling and Term Exchange retry") # v3.18.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19ce192cd7 ]
Since mcmd->sess->port_name is eight bytes long, use %8phC to format that
port name instead of %phC.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <gmalavali@marvell.com>
Fixes: 726b854870 ("qla2xxx: Add framework for async fabric discovery") # v4.11.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f29456d08 ]
Some definitions of Inner Cacheability attibutes need to be corrected.
Fixes: 8c828a535e ("irqchip/gicv3-its: Restore all cacheability attributes")
Signed-off-by: Hongbo Yao <yaohongbo@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6339a3889a ]
When loading an ELF image via kexec_file the segment alignment is ignored
in the calculation for the load address of the next segment. When there are
multiple segments this can lead to segment overlap and thus load failure.
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Fixes: 8be0188271 ("s390/kexec_file: Add ELF loader")
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59d63de076 ]
Clang points out a syntax error, as the etr_catu_buf_ops structure is
declared 'static' before the type is known:
In file included from drivers/hwtracing/coresight/coresight-tmc-etr.c:12:
drivers/hwtracing/coresight/coresight-catu.h:116:40: warning: tentative definition of variable with internal linkage has incomplete non-array type 'const struct etr_buf_operations' [-Wtentative-definition-incomplete-type]
static const struct etr_buf_operations etr_catu_buf_ops;
^
drivers/hwtracing/coresight/coresight-catu.h:116:21: note: forward declaration of 'struct etr_buf_operations'
static const struct etr_buf_operations etr_catu_buf_ops;
This seems worth fixing in the code, so replace pointer to the empty
constant structure with a NULL pointer. We need an extra NULL pointer
check here, but the result should be better object code otherwise,
avoiding the silly empty structure.
Fixes: 434d611cdd ("coresight: catu: Plug in CATU as a backend for ETR buffer")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Fixed line over 80 characters]
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14bebe3c90 ]
When flushing out dirty pages, the fact that we may hit fatal errors
is not a reason to stop writeback. Those errors are reported through
fsync(), not through the flush mechanism.
Fixes: a6598813a4 ("NFS: Don't write back further requests if there...")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4be5975aea ]
Further fix the file locking in the afs filesystem client in a number of
ways, including:
(1) Don't submit the operation to obtain a lock from the server in a work
queue context, but rather do it in the process context of whoever
issued the requesting system call.
(2) The owner of the file_lock struct at the front of the pending_locks
queue now owns right to talk to the server.
(3) Write locks can be instantly granted if they don't overlap with any
other locks *and* we have a write lock on the server.
(4) In the event of an authentication/permission error, all other matching
pending locks requests are also immediately aborted.
(5) Properly use VFS core locks_lock_file_wait() to distribute the server
lock amongst local client locks, including waiting for the lock to
become available.
Test with:
sqlite3 /afs/.../scratch/billings.sqlite <<EOF
CREATE TABLE hosts (
hostname varchar(80),
shorthost varchar(80),
room varchar(30),
building varchar(30),
PRIMARY KEY(shorthost)
);
EOF
With the version of sqlite3 that I have, this should fail consistently with
EAGAIN, whether or not the program is straced (which introduces some delays
between lock syscalls).
Fixes: 0fafdc9f88 ("afs: Fix file locking")
Reported-by: Jonathan Billings <jsbillin@umich.edu>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68ce801ffd ]
Fix AFS file locking to allow fine grained locks as some applications, such
as firefox, won't work if they can't take such locks on certain state files
- thereby preventing the use of kAFS to distribute a home directory.
Note that this cannot be made completely functional as the protocol only
has provision for whole-file locks, so there exists the possibility of a
process deadlocking itself by getting a partial read-lock on a file first
and then trying to get a non-overlapping write-lock - but we got the
server's read lock with the first lock, so we're now stuck.
OpenAFS solves this by just granting any partial-range lock directly
without consulting the server - and hoping there's no remote collision. I
want to implement that in a separate patch and it requires a bit more
thought.
Fixes: 8d6c554126b8 ("AFS: implement file locking")
Reported-by: Jonathan Billings <jsbillings@jsbillings.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 328e9f6973 ]
The error from snd_usb_mixer_apply_create_quirk() is ignored in the
current usb-audio driver code, which will continue the probing even
after the error. Let's take it more serious.
Fixes: 7b1eda223d ("ALSA: usb-mixer: factor out quirks")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 648865a79d ]
In 2D transfers (for the AXI DMAC), the number of frames (numf) represents
Y_LENGTH, and the length of a frame is X_LENGTH. 2D transfers are useful
for video transfers where screen resolutions ( X * Y ) are typically
aligned for X, but not for Y.
There is no requirement for Y_LENGTH to be aligned to the bus-width (or
anything), and this is also true for AXI DMAC.
Checking the Y_LENGTH for alignment causes false errors when initiating DMA
transfers. This change fixes this by checking only that the Y_LENGTH is
non-zero.
Fixes: 0e3b67b348 ("dmaengine: Add support for the Analog Devices AXI-DMAC DMA controller")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f57c4bbf34 ]
NEXTHDR_MAX is 255. What happens here is that we take a u8 value
"hdr->nexthdr" from the network and then look it up in
lowpan_nexthdr_nhcs[]. The problem is that if hdr->nexthdr is 0xff then
we read one element beyond the end of the array so the array needs to
be one element larger.
Fixes: 92aa7c65d2 ("6lowpan: add generic nhc layer interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Acked-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7861adbe3 ]
Each eTSEC MAC has its own TBI (SGMII) PCS and private MDIO bus.
But due to a DTS oversight, both SGMII-compatible MACs of the LS1021 SoC
are pointing towards the same internal PCS. Therefore nobody is
controlling the internal PCS of eTSEC0.
Upon initial ndo_open, the SGMII link is ok by virtue of U-boot
initialization. But upon an ifdown/ifup sequence, the code path from
ndo_open -> init_phy -> gfar_configure_serdes does not get executed for
the PCS of eTSEC0 (and is executed twice for MAC eTSEC1). So the SGMII
link remains down for eTSEC0. On the LS1021A-TWR board, to signal this
failure condition, the PHY driver keeps printing
'803x_aneg_done: SGMII link is not ok'.
Also, it changes compatible of mdio0 to "fsl,etsec2-mdio" to match
mdio1 device.
Fixes: 055223d4d2 ("ARM: dts: ls1021a: Enable the eTSEC ports on QDS and TWR")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff6d27823f ]
The 32-bit vDSO is not needed and not normally built for 64-bit
little-endian configurations. However, the vdso_install target still
builds and installs it. Add the same config condition as is normally
used for the build.
Fixes: e0d0059169 ("powerpc/vdso: Disable building the 32-bit VDSO ...")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
