If we're sending more pages via kernel_sendpage(), then set
MSG_SENDPAGE_NOTLAST.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Implement bus recovery methods for i2c-imx so we can recover from
situations where SCL/SDA are stuck low.
Once i2c bus SCL/SDA are stuck low during transfer, config the i2c
pinctrl to gpio mode by calling pinctrl sleep set function, and then
use GPIO to emulate the i2c protocol to send nine dummy clock to recover
i2c device. After recovery, set i2c pinctrl to default group setting.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is a 24c08 chip connected to i2c bus on Intel Galileo Gen2 board. Enable
it via ACPI ID INT3499.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Intel Galileo Gen2 the GPIO expanders are connected to the i2c bus. For
those devices the ACPI table has specific parameters that refer to an actual
i2c host controller. Since MFD now copes with that specific configuration we
have to provide a necessary information how to distinguish devices in ACPI
namespace. Here the _ADR values are provided.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Intel Galileo boards the GPIO expander is connected to i2c bus. Moreover it
is able to generate interrupt, but interrupt line is connected to GPIO. That's
why we have to have GPIO driver in place when we will probe i2c host with
device connected to it.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is at least one board on the market, i.e. Intel Galileo Gen2, that uses
_ADR to distinguish the devices under one actual device. Due to this we have to
improve the quirk in the MFD core to handle that board.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for on-chip I2C controller used on newer UniPhier SoCs
such as PH1-Pro4, PH1-Pro5, etc. This adapter is equipped with
8-depth TX/RX FIFOs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for on-chip I2C controller used on old UniPhier SoCs
such as PH1-LD4, PH1-sLD8, etc. This adapter is so simple that
it has no FIFO in it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The patch reverts commit a445900c90 (i2c: designware: Add support for
AMD I2C controller). It never worked anyhow because it did not register
a proper clkdev.
Since kernel 4.1 starts to support APD, there is no need to get freq
from id->driver_data for AMD0010. clkdev is supposed to be already
registered in APD.
So, revert old design and make AMD0010 looks like other ones.
Signed-off-by: Ken Xue <Ken.Xue@amd.com>
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update the documentation about:
1. Usage of PMU_SPARE2 register.
Bootloaders on Exynos542x-based boards often use the register
PMU_SPARE2 (0x908) in the same way as on Exynos3250: as a indicator
the secondary CPU was booted on. The bootloader will set this value
to non-zero, after sucessfull power up of secondary CPU. In the same
time this booted CPU will stuck (spin) waiting for software reset.
2. Exynos542x entry address for secondary CPU boot up after system
suspend (with MCPM enabled and in non-secure mode).
See arch/arm/mach-exynos/mcpm-exynos.c for source code.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Adds to the node of the DISP1 power domain the two clocks that need to
be reparented while the domain is powered off:
CLK_MOUT_ACLK200_DISP1_SUB and CLK_MOUT_ACLK300_DISP1_SUB.
Otherwise the state is unknown at power up and the mixer's clocks are
all messed up.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Link: http://lkml.kernel.org/g/561CDC33.7050103@collabora.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Since commit 29e5eea06b ("ARM: EXYNOS: Get current parent clock for
power domain on/off") the "pclkN" names of "clock-names" property is not
parsed any more. The bindings and driver were updated but the example
was not. Fix the example now.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The property name should be "gpio", not "gpios". Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The property name should be "gpio", not "gpios". Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Exynos USB2 PHY driver now supports VBUS regulator, so add it to all
boards which have it available. This also fixes commit
7eec126675 ("ARM: dts: Add Maxim 77693 PMIC to exynos4412-trats2"),
which added new regulators to Trats2 board, but without linking them to
the consumers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 7eec126675 ("ARM: dts: Add Maxim 77693 PMIC to exynos4412-trats2")
Signed-off-by: Kukjin Kim <kgene@kernel.org>
When the DISP1 power domain is powered off, there's two clocks that need
to be temporarily reparented to OSC, and back to their original parents
when the domain is powered on again.
We expose these two clocks in the DT bindings so that the DT node of the
power domain can reference them.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Odroid XU4 has a RTL8153-CG gigabit Ethernet adapter, connected over
USB 3.0.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Odroid-XU4 has a RTL8153-CG gigabit Ethernet adapter, connected over
USB 3.0.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Marvell WiFi-Ex driver tries to load a firmware on probe. So if the
driver is built-in and probed before a firmware is available, this is
not loaded and the chip does not work.
This happens for example if an initramfs isn't used since the driver is
probed before the root filesystem is mounted.
Change the default config since the driver isn't needed for machines to
boot and is more convenient to have it enabled as a module to avoid
requiring an initramfs or to have the firmware built into the kernel.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The simplefb driver allows the kernel to render on a pre-allocated
buffer that's been initialized by firmware before the kernel boots.
This option was enabled to have display working on the Exynos5250
Snow Chromebook by commit da9d0fbf5e ("ARM: exynos: defconfig
update") since proper DRM/KMS support did not exist at that time.
But now that the Exynos DRM driver has support for this hardware,
there is no need to have simplefb enabled. In fact, if a user has
a u-boot that injects the simplefb dev node to the FDT before pass
it to the kernel, display won't be properly initialized and only a
blank screen will be shown since there isn't a proper handoff from
the simplefb driver to the Exynos DRM driver.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Tested-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Odroid XU3 family boards come with RGB LEDs. Enabling LEDS_GPIO and
LEDS_PWM allows monitoring the board alive state (heartbeat) and
MMC/SDcard IO usage.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
[k.kozlowski: Rewritten the commit message]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
DWC2 (s3c-hsotg) hardware module is available on many Exynos based boards,
so enable DWC2 driver as well as the most common USB Ethernet gadget.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
DWC2 (s3c-hsotg) hardware module is available on many Exynos based boards,
so enable DWC2 driver as well as the most common USB Ethernet gadget.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos5420 Peach Pit and Exynos5800 Peach Pi boards have a built-in
Silicon Motion USB UVC WebCam. Enable support for the USB Video Class
driver and its needed media Kconfig symbols so the camera is supported.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Remove the mailbox attribute data, irq info and hwmod addr space
data that are used for creating the legacy-style mailbox devices,
there is no need for these as the support for legacy-mode for this
IP is being dropped.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The legacy-style device creation logic for hwspinlock
has been removed after the DT-support was added to the
driver. The hwmod addr space for spinlock is therefore
no longer needed, so remove it.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The legacy-style device creation logic for hwspinlock
has been removed after the DT-support was added to the
driver. The hwmod addr space for spinlock is therefore
no longer needed, so remove it.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
GPMC address information is provided by device tree. No longer need
to include this information within hwmod.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
[paul@pwsan.com: fixed chip names in subject line]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
There are some differences of mobile storage host between exynos3250
and exnos5250. For example, exynos3250 supports the HS400 mode, but
exynos5250 doesn't support it.
Since exynos3250 can perform the similar function with exynos5420
compatible, this patch changes the compatible from exynos5250 to
exynos5420 for mshc.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add the Altera PCIe host controller driver.
[bhelgaas: whitespace, fold in DT and maintainer updates, OF_PCI
dependency from Arnd]
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rob Herring <robh@kernel.org> (DT binding)
Include asm-generic/msi.h to support CONFIG_GENERIC_MSI_IRQ_DOMAIN.
This fixes a compilation error:
include/linux/msi.h:123:21: fatal error: asm/msi.h: No such file or directory
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If the CLEAN_SHUTDOWN flag is not set when a cache is loaded then all cache
blocks are marked as dirty and a full writeback occurs.
__commit_transaction() is responsible for setting/clearing
CLEAN_SHUTDOWN (based the flags_mutator that is passed in).
Fix this issue, of the cache's on-disk flags being wrong, by making sure
__commit_transaction() does not reset the flags after the mutator has
altered the flags in preparation for them being serialized to disk.
before:
sb_flags = mutator(le32_to_cpu(disk_super->flags));
disk_super->flags = cpu_to_le32(sb_flags);
disk_super->flags = cpu_to_le32(cmd->flags);
after:
disk_super->flags = cpu_to_le32(cmd->flags);
sb_flags = mutator(le32_to_cpu(disk_super->flags));
disk_super->flags = cpu_to_le32(sb_flags);
Reported-by: Bogdan Vasiliev <bogdan.vasiliev@gmail.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
btree_split_beneath()'s error path had an outstanding FIXME that speaks
directly to the potential for _not_ cleaning up a previously allocated
bufio-backed block.
Fix this by releasing the previously allocated bufio block using
unlock_block().
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <thornber@redhat.com>
Cc: stable@vger.kernel.org
Commit 4c7e309340 ("dm btree remove: fix bug in redistribute3") wasn't
a complete fix for redistribute3().
The redistribute3 function takes 3 btree nodes and shares out the entries
evenly between them. If the three nodes in total contained
(MAX_ENTRIES * 3) - 1 entries between them then this was erroneously getting
rebalanced as (MAX_ENTRIES - 1) on the left and right, and (MAX_ENTRIES + 1) in
the center.
Fix this issue by being more careful about calculating the target number
of entries for the left and right nodes.
Unit tested in userspace using this program:
https://github.com/jthornber/redistribute3-test/blob/master/redistribute3_t.c
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
- Add IOMUXC LPSR (Low Power State Retention) device for i.MX7D.
- Add a few low power mode related devices and touch controller for
i.MX6UL.
- Add a number of devices for i.MX7D SDB board support, USB, Dual FEC,
and eMMC5.0.
- i.MX6 Boundary Devices updates: relicense under GPLv2/X11, add Okaya
LCD, touch and wifi support, add new boards Nitrogen6_Lite and
Nitrogen6_Max.
- Enable touch screen and NAND Flash controller for a few Vybrid
devices.
- Some random and small updates on LS1021A and MXS support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWJQUPAAoJEFBXWFqHsHzOo+cH/irx+abVdFV97q6M0VwFsQ3/
Tf4/CsdiTjM5ZDrKZEtXzP8BZl+ZO4tQXLspP+wVceQ+PVUiVvdAHu0l68iuJRrA
+Bj9VrLIzMDf7FVpzbZHZD3kd1NALGh/5i0TerkuZMNl1KH57HyGjLnjKH43n7uz
mFPeZFAQMwSjEnRJj/6217Itqi+LurARJsnXQs6uhQ7feSsA88HU3EQ8QsiZqiAu
MULAJBYaE09shlokuXIKx67t8outdb8C0Uue64nt42y8NR0m5eVVG7NJoF+23T6C
CRX5zveYa7D2QXTkihvjdRpazhLiPnwV3RCVejLOZMk0G14hD9U39jkTp+9ws1w=
=kPBq
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree changes for 4.4:
- Add IOMUXC LPSR (Low Power State Retention) device for i.MX7D.
- Add a few low power mode related devices and touch controller for
i.MX6UL.
- Add a number of devices for i.MX7D SDB board support, USB, Dual FEC,
and eMMC5.0.
- i.MX6 Boundary Devices updates: relicense under GPLv2/X11, add Okaya
LCD, touch and wifi support, add new boards Nitrogen6_Lite and
Nitrogen6_Max.
- Enable touch screen and NAND Flash controller for a few Vybrid
devices.
- Some random and small updates on LS1021A and MXS support.
* tag 'imx-dt-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (53 commits)
ARM: dts: ls1021a: Add quirk for Erratum A009116
ARM: imx6sx-sdb: Fix typo in regulator enable GPIO property
ARM: dts: imx6: phyFLEX: fix typo in "pinctrl-names"
ARM: dts: imx6: change the core clock of spdif
ARM: dts: vf-colibri: enable NAND flash controller
ARM: dts: vf610twr: add NAND flash controller peripherial
ARM: dts: imx: add Boundary Devices Nitrogen6_Lite board
ARM: dts: imx: add Boundary Devices Nitrogen6_Max board
ARM: dts: imx6dl-nitrogen6x: change manufacturer to Boundary Devices
ARM: dts: imx6q-nitrogen6x: change manufacturer to Boundary Devices
of: Add Boundary Devices Inc. vendor prefix
ARM: dts: imx6qdl-sabrelite: relicense under GPLv2/X11
ARM: dts: imx6qdl-nitrogen6x: relicense under GPLv2/X11
ARM: dts: imx6qdl-nitrogen6x: add wifi wl1271 support
ARM: dts: imx6dql-nitrogen6x: add touchscreen support
ARM: dts: imx6qdl-sabrelite: add Okaya LCD panel
ARM: dts: imx6qdl-nitrogen6x: add Okaya LCD panel
ARM: dts: vf500-colibri: Add device tree node for touchscreen support
ARM: dts: i.MX35: fix cpu compatible value
ARM: dts: i.MX31: fix cpu compatible value
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Enable suspend and cpufreq support for i.MX6UL
- Add platform level ENET initialization support for i.MX7D
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWJP9yAAoJEFBXWFqHsHzOJvQH/3sncCMvFmOXX1hBJzb4BzE6
4Ke4AC39v1TuviNkVZooMiVlW5uf4tvyvyv47GjF88yRsHJmvt1s0T7502v4+dib
Ak6dj58uqdC4yj6RF5eZBwqHV4s3nZbESYt4Dr17rka/HqhvhH7yxFpWBzPWqLUb
YK5nlyBe8r9Mrsgr8mkFEKHmzgMhOTlomkUk3f5BL7TjrRCA+b5Czed/P0hZ7OVx
cIqALqMregcqmvH21bA6feSs1NARLfcBraWH4/YxSRFrXng8XCb1bGF6P8U78bSz
aQ6VZFWEInJBNKfQR+5N5+yfPnm25AIAHdqv1cyIODBPbFy7t5hyyzdmtEmNskM=
=naPW
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
The i.MX SoC updates for 4.4:
- Enable suspend and cpufreq support for i.MX6UL
- Add platform level ENET initialization support for i.MX7D
* tag 'imx-soc-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: add cpufreq device for imx6ul
ARM: imx: add enet init for i.MX7D platform
ARM: imx7d: add imx7d iomux-gpr field define
ARM: imx: add suspend/resume support for i.mx6ul
Signed-off-by: Olof Johansson <olof@lixom.net>
The patch adds the HWEQ function for the speaker output. User can set the
HWEQ parameters using the ALSA binary control byte-by-byte. We use the
following struct array to store the HWEQ parameters for implementing as
simple as possible.
struct rt5645_eq_param_s {
unsigned short reg;
unsigned short val;
};
It supports the variant length of the HWEQ parameters that are required.
We add the validating function in the function "rt5645_hweq_put" of the
ALSA binary control to avoid the user that puts the invalid parameters.
In the HWEQ enable function of speaker event, we also add the validating
function to prevent that the invalid parameters are applied to codec.
The HWEQ parameters should be controlled by DAPM for a specific sequence,
so the parameters will be applied to the codec in the speaker power up
event of DAPM, and will be disabled in the speaker power down event of
DAPM.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add spi DTS node to the mt8173 and mt8173-evb.
Add dts nodes for the subsystem clocks on mt8173.
This includes mmsys, imgsys, vdecsys, vencsys, vencltsys.
Add clock nodes to the scpsys binding, which are needed to
access the registers of venc and venc_lt power domains.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=laqA
-----END PGP SIGNATURE-----
Merge tag 'v4.3-next-arm64' of https://github.com/mbgg/linux-mediatek into next/arm64
Correct i2c DTS node names in mt8173.dtsi.
Add spi DTS node to the mt8173 and mt8173-evb.
Add dts nodes for the subsystem clocks on mt8173.
This includes mmsys, imgsys, vdecsys, vencsys, vencltsys.
Add clock nodes to the scpsys binding, which are needed to
access the registers of venc and venc_lt power domains.
* tag 'v4.3-next-arm64' of https://github.com/mbgg/linux-mediatek:
arm64: dts: mt8173: Add clocks for SCPSYS unit
arm64: dts: mt8173: Add subsystem clock controller device nodes
arm64: dts: Add spi bus dts
arm64: mt8173.dtsi: correct i2c node names
Signed-off-by: Olof Johansson <olof@lixom.net>
The regualtor-compatible binding is deprecated, instead the node name
is used.
Mediatek timer driver supports as well mt8127, mt8135 and mt8173. Add
these SOCs to the bindings list.
Power domains venc and venc_lt need clocks two extra clocks to access
their registers. We update the bindings documentation about this.
Update SMP bindings documentation by adding support for mt6589 and mt81xx SOCs.
Update mt8127.dtsi and mt8135.dtsi to enable SMP support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Lj7i
-----END PGP SIGNATURE-----
Merge tag 'v4.3-next-dts' of https://github.com/mbgg/linux-mediatek into next/dt
Delete regulator-compatible usage in mt8135-evbp1.dts.
The regualtor-compatible binding is deprecated, instead the node name
is used.
Mediatek timer driver supports as well mt8127, mt8135 and mt8173. Add
these SOCs to the bindings list.
Power domains venc and venc_lt need clocks two extra clocks to access
their registers. We update the bindings documentation about this.
Update SMP bindings documentation by adding support for mt6589 and mt81xx SOCs.
Update mt8127.dtsi and mt8135.dtsi to enable SMP support.
* tag 'v4.3-next-dts' of https://github.com/mbgg/linux-mediatek:
ARM: dts: mt8127: enable basic SMP bringup for mt8127
ARM: dts: mt8135: enable basic SMP bringup for mt8135
devicetree: bindings: add new SMP enable method Mediatek SoC
dt-bindings: soc: Add clocks for Mediatek SCPSYS unit
dt-bindings: add more MediaTek SoC to mtk-timer binding
ARM: dts: mt8135-evbp1: remove regulator-compatible usage
Signed-off-by: Olof Johansson <olof@lixom.net>
This fixes the corner-case where the pmic is initialized by the bootloader, but
not the pmic watchdog.
Add support for active wakeup to the scpsys. This allows to keep the power of
a scpsys domain during suspend state.
With version v4.3 new subsystem clocks are added to the clock dirver. In late
init the kernel turns off all unused clocks. This can provoke a hang if
the kernel tries to access the venc and venc_lt power domain registers.
Add the necessary parent clocks for this power domains to
the scpsys so that no random hang happens.
The bootloader of mt6589, mt8135 and mt1827 does not turn on the arm-arch-timer.
As there is no opensource bootloader in the near future for this architectures
we enable the arch timer at kernel boot. We need the arch timer for SMP boot.
Add support for SMP on mt6589, mt8127 and mt8135.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWI4fcAAoJELQ5Ylss8dNDANYP/1hhCHTT3ssT0eURn+gGJX/e
f5J0dgX9KfJK7Ds0fznD6iMMHgp+EgK7WXI6vsO0VcbvokfS2KowS3NbeRKTnbTS
gmPOWvbFooHVIhzTom3serxyc9AgpnAG7WaRNxVD0CgaufeOlgbFtmOIdxze2cdE
S1ucq3JWJcpiCUaI3S9zRc3kkY9W/wpTEKNY98S4K3blKnWWT0sHSQxSGjoKy3wk
f1qhVjX82FeFizVSf5Ca6iqyXSFiO9gXQWvfVnS2kZE+gO/sh4df8tg8psxVqfqK
//3INxXhqkgkN4O3W+y3nUfSAQ5fElknnhiHaxAsl0PXFGMHROT3xtNR21syVkDh
dge/Eu34KyROPj68UbE2MnqnQbbSl2KbHsapT4ls8LiDWJPisjhhOmWL459eIS5X
+ycQniAxOpTgSIjYJnBwCBesru8OdfGNWRqm+SpGHyrClNtJt66/pK4AWEN2fgX4
eI8CeZ13uiuiQNmROOKRmTzSoG7ZBQMFK4g5Cy1Dl5bkGiJaednv6HnZoWqPZ4PG
isiOdsmiPsGB5GgvTpue996Nfc2kfHx2emr8+kxM8wejRWQJqmwLwTkX9bZ3dpFQ
7RGK46qN34tbJH/bgrck99Zgfg7OxChTQqVL0oTEjCCABK41clDFbguJiCV8SENw
uxtnI++cVFcUwxv7Qz0t
=iuHl
-----END PGP SIGNATURE-----
Merge tag 'v4.3-next-soc' of https://github.com/mbgg/linux-mediatek into next/soc
Do the initial setting of the pmic wrap interrupt before requesting the interrupt.
This fixes the corner-case where the pmic is initialized by the bootloader, but
not the pmic watchdog.
Add support for active wakeup to the scpsys. This allows to keep the power of
a scpsys domain during suspend state.
With version v4.3 new subsystem clocks are added to the clock dirver. In late
init the kernel turns off all unused clocks. This can provoke a hang if
the kernel tries to access the venc and venc_lt power domain registers.
Add the necessary parent clocks for this power domains to
the scpsys so that no random hang happens.
The bootloader of mt6589, mt8135 and mt1827 does not turn on the arm-arch-timer.
As there is no opensource bootloader in the near future for this architectures
we enable the arch timer at kernel boot. We need the arch timer for SMP boot.
Add support for SMP on mt6589, mt8127 and mt8135.
* tag 'v4.3-next-soc' of https://github.com/mbgg/linux-mediatek:
ARM: mediatek: add smp bringup code
ARM: mediatek: enable gpt6 on boot up to make arch timer working
soc: mediatek: Fix random hang up issue while kernel init
soc: mediatek: add scpsys support active_wakeup
soc: mediatek: Move the initial setting of pmic wrap interrupt before requesting irq.
Signed-off-by: Olof Johansson <olof@lixom.net>
A bunch of defconfig changes to enable support for new drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=g7fp
-----END PGP SIGNATURE-----
Merge tag 'sunxi-defconfig-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/defconfig
Allwinner defconfig changes for 4.4
A bunch of defconfig changes to enable support for new drivers.
* tag 'sunxi-defconfig-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi_defconfig: enable MODULE_UNLOAD
can: Allwinner A10/A20 CAN Controller support - Defconfig
can: Allwinner A10/A20 CAN Controller support - Defconfig
ARM: sunxi_defconfig: Enable LRADC keys (KEYBOARD_SUN4I_LRADC)
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for the Allwinner R8 SoC used in the CHIP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o6P8
-----END PGP SIGNATURE-----
Merge tag 'sunxi-core-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/soc
Allwinner core changes for 4.4
Add support for the Allwinner R8 SoC used in the CHIP.
* tag 'sunxi-core-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi: Add R8 support
Signed-off-by: Olof Johansson <olof@lixom.net>
Rockchip Kconfig options, fixing a possible null-pointer and a
typo in the dt-bindings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJWIlknAAoJEPOmecmc0R2BrTkH/3w+1ZZuvtfQmzBkPwJGJ9vJ
zZFZLZqD0NADib8sOhFnJxTfxrhoE/Bfijqk4wPfjdKta2GABfljGbLDanQB8Yr9
Ip+fyflQ6cd925dEuPccHMbumZep+QuSIGYjOGFIuRbbjCdOY5MB+I2Yhvognwus
Xh4FtjS7CL6ruotmyOcMtnpNDCAvc8NSwO7xBqxYRPcgd+DY8+86cD/dUpvmD4Kr
pGtUXkfQpAjBhV9P6RuP63gO42JD1VMb7c6idd+B/tzbJxI08CTDolwqvyujVkHf
KeRvu7g8qKKUwL5ffOImR4tR/T2o1wDLwfxuUJXW+mIVJa72qA+h90aNOhM2iC8=
=Qk94
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rockchip-drivers2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/drivers
Some fixes for the new power-domain driver, including restricting
Rockchip Kconfig options, fixing a possible null-pointer and a
typo in the dt-bindings.
* tag 'v4.4-rockchip-drivers2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: rockchip: Restrict to ARCH_ROCKCHIP
Signed-off-by: Olof Johansson <olof@lixom.net>
More DT patches for 4.4, mostly with new boards coming in (CHIP, BananaPi
M2, pcduino2), further consolidation for the q8-based designs and a bunch
of random patches enhancing support for existing boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vcTX
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Allwinner DT changes for 4.4, round 2
More DT patches for 4.4, mostly with new boards coming in (CHIP, BananaPi
M2, pcduino2), further consolidation for the q8-based designs and a bunch
of random patches enhancing support for existing boards
* tag 'sunxi-dt-for-4.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (27 commits)
ARM: dts: sun6i: Add a dts file for the Sinovoip BPI-M2 board
ARM: dts: sun6i: Add mmc2_pins_a pinmux setting to sun6i-a31.dtsi
ARM: dts: sunxi: Fix interrupt-cells for [r]pio on A23/A31/A33/A80
ARM: dts: sun8i: Add NMI interrupt controller node
ARM: dts: sun6i: hummingbird: Enable AXP221 DC5LDO regulator as "vdd-cpus"
ARM: dts: sun6i: hummingbird: Use axp22x.dtsi for AXP221 regulators
ARM: dts: sun6i: hummingbird: Fix VDD-CPU and VDD-GPU regulator names
ARM: dts: sun7i: Add regulator configuration for pcDuino v3 Nano
ARM: dts: sun6i: Turn on gmac on Colombus
ARM: dts: sun8i: Make et-q8-v1.6.dts a symlink to q8-tablet.dts
ARM: dts: sun8i: Make ippo-q8h-v*.dts a symlink to q8-tablet.dts
ARM: dts: sun8i: Add sun8i-a23-q8-tablet.dts file
ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsi
ARM: dts: sunxi: Enable PWM controller on Q8 format tablets
ARM: dts: sun5i: Add PWM channel 0 pinmux setting for A13/A10s
ARM: dts: sun5i: Add PWM controller node for A13 / A10s
ARM: sun5i: Add C.H.I.P DTS
ARM: dts: sunxi: Add dtsi for AXP22x PMIC
ARM: dts: sun7i: Correct USB regulators on pcDuino v3 Nano
ARM: sun5i: dt: Add UART3 CTS and RTS pins
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Update the v7 defconfig witth usefull config for the Seagate NAS
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlYiY+EACgkQCwYYjhRyO9WANACfdPTeOBofTpIFChzcNlg823Su
BIYAn1XQ+oxXKt/mmh0xWRJGcIEKQJPP
=+DPM
-----END PGP SIGNATURE-----
Merge tag 'mvebu-config-4.4-1' of git://git.infradead.org/linux-mvebu into next/defconfig
mvebu config for 4.4 (part 1)
Update the v7 defconfig witth usefull config for the Seagate NAS
* tag 'mvebu-config-4.4-1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: enable options for Seagate NAS in mvebu_v7_defconfig
Signed-off-by: Olof Johansson <olof@lixom.net>
This cycle is bigger than usual :
- magician was greatly enhanced (new IPs discovered, ...)
- almost all legacy board files have been updated to the
new PWM API (mostly for backlight control)
- some minor fixes in raumfeld, z2 and mioa701
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wWU6
-----END PGP SIGNATURE-----
Merge tag 'pxa-for-4.4' of https://github.com/rjarzmik/linux into next/cleanup
This is the pxa changes for v4.4 cycle.
This cycle is bigger than usual :
- magician was greatly enhanced (new IPs discovered, ...)
- almost all legacy board files have been updated to the
new PWM API (mostly for backlight control)
- some minor fixes in raumfeld, z2 and mioa701
* tag 'pxa-for-4.4' of https://github.com/rjarzmik/linux: (44 commits)
ARM: pxa: remove incorrect __init annotation on pxa27x_set_pwrmode
ARM: pxa: raumfeld: make some variables static
ARM: pxa: magician: Remove pdata for pasic3-leds
ARM: pxa: magician: Add support for PXA27x UDC
ARM: pxa: magician: Add support for MAX1587A Vcore regulator
ARM: pxa: magician: Change comments to be more informative
ARM: pxa: magician: Move platform_add_devices() to the end of magician_init()
ARM: pxa: magician: Add missing regulator for PWM backlight
ARM: pxa: magician: Add debug message for backlight brightness function
ARM: pxa: magician: Remove definition of the STUART port
ARM: pxa: magician: Fix wrongly enabled USB host ports
ARM: pxa: magician: Fix support for Intel Strata NOR Flash
ARM: pxa: magician: Fix redundant GPIO request for pxaficp_ir
ARM: pxa: magician: Fix platform data for both PXA27x I2C controllers
ARM: pxa: magician: Fix and add charging detection functions
ARM: pxa: magician: Optimize Samsung LCD refresh to 50Hz
ARM: pxa: magician: Rename charger cable detection EGPIOs
ARM: pxa: magician: Optimize powerup delays for Samsung LCD
ARM: pxa: magician: Rename abstract LCD GPIOs
ARM: pxa: magician: Add new discovered EGPIO pins
...
Signed-off-by: Olof Johansson <olof@lixom.net>
