As a part of the work to move xfs global stats from procfs to sysfs,
this patch creates the symlink from proc/fs/xfs/stat to sys/fs/xfs/stats.
Signed-off-by: Bill O'Donnell <billodo@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Currently, xfs global stats are in procfs. This patch introduces
(replicates) the global stats in sysfs. Additionally a stats_clear file
is introduced in sysfs.
Signed-off-by: Bill O'Donnell <billodo@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The LinkSprite pcDuino v3 Nano's two USB host ports are powered by a
single RT9701GB regulator, which has its enable input tied to the A20's
PD2 pin, pulled up to 3v3 via a 10k resistor.
However, the script.bin that shipped with the device listed PH11 and PH3
as Vbus control pins for the two USB ports. Neither of these are
actually connected to anything.
Siarhei Siamashka spotted this problem while reviewing the other
LinkSprite boards. This patch fixes it by only defining a single
regulator, controlled by PD2. Testing shows that the USB ports are now
(correctly) only powered up once the USB PHY driver is loaded.
Reported-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Adam Sampson <ats@offog.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pull scheduler fix from Thomas Gleixner:
"Fix a long standing state race in finish_task_switch()"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Fix TASK_DEAD race in finish_task_switch()
Pull perf fix from Thomas Glexiner:
"Fix build breakage on powerpc in perf tools"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Fix build break on powerpc due to sample_reg_masks
Pull maintainer email update from Thomas Gleixner:
"Change Matt Fleming's email address in the maintainers file"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
MAINTAINERS: Change Matt Fleming's email address
Pull irq fixes from Thomas Gleixner:
"Three trivial commits:
- Fix a kerneldoc regression
- Export handle_bad_irq to unbreak a driver in next
- Add an accessor for the of_node field so refactoring in next does
not depend on merge ordering"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqdomain: Add an accessor for the of_node field
genirq: Fix handle_bad_irq kerneldoc comment
genirq: Export handle_bad_irq
Add a separate pinctrl node for the UART3 CTS and RTS pins shared between
the A10s and A13.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
The uart3 pins are shared between the A10s and A13, move the pinctrl node
to the common DTSI to avoid duplication.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
The R8 is very close to the A13, but it still has a few differences,
notably a composite output, which the A13 lacks.
Add a DTSI based on the A13's to hold those differences.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Enable the otg/drc usb controller on the pcDuino1/2 board. Note
that the pcDuino1 FEX file from the vendor contains the following
information in the [usbc0] section:
usb_id_gpio = port:PH04<0><1><default><default>
usb_det_vbus_gpio = port:PH05<0><0><default><default>
usb_drv_vbus_gpio = port:PB09<1><0><default><0>
While the pcDuino2 FEX has:
usb_id_gpio = port:PH04<0><1><default><default>
usb_det_vbus_gpio = port:PH05<0><0><default><default>
usb_drv_vbus_gpio = port:PD02<1><0><default><0>
The ID pin is indeed PH4. The PD2 pin can be used to switch power
on/off for the USB Type A receptacle on pcDuino2, but it has nothing
to do with the MicroUSB OTG receptacle. The VBUS pin of the MicroUSB
receptacle is always connected to 5V according to the schematics
(both pcDuino1 and pcDuino2) and confirmed by doing some tests on
pcDuino2. The PH5 pin is just one of the pins on the J8 expansion
header and has nothing to do with USB OTG. The PB9 pin is pulled
up and connected to the N_VBUSEN pin of AXP209 PMIC, while the
VBUS pin of AXP209 only has a capacitor between it and the
ground (this pin is not used for anything else).
To sum it up. Only the ID pin (PH4) has a real use. And 5V voltage
is always served to the MicroUSB OTG receptacle no matter what is
the state of the PB9/PD2 pins.
This patch has been tested on pcDuino2 to work fine in a host role
with a USB keyboard connected via an OTG cable. It also works fine
in a device role (cdc_ether) with a regular Micro-B cable connected
to a desktop PC.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is a set of three bug fixes, two of which are regressions from recent
updates (the 3ware one from 4.1 and the device handler fixes from 4.2).
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEbBAABAgAGBQJWGgjcAAoJEDeqqVYsXL0MDjIH+N1poa/RB6jU163q1bMnJlp6
6ygEqLtrJH7FNjadiRuYjsZaSWfuabbEyj0zV8t6S7Z2wWQmXG7Qfkic3W0CZa9u
qCa3aPmRB06Al9nwmEDlgilBfFP5hWkWldiPF7uEBqcCsBtzT3cxxUnyoCS1fy28
USMHSQ4fnQDFdaTafXqDCRrMjXIJLeRY1Gg7YuiG7l6h4YK5qPC+0cCpiIeDyDyI
WjTr/SbFzIyDg0r/SNwjZqbhY2+s4a2/4GcAmjpBMWvg2GnXDGt6vxibRvrwZfHf
PtUvsVS7eJhAOAKs67KOJavP6kvheXkj/QTZWq5Y/DqDrd/14qIgjOPpIHYyig==
=20ji
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of three bug fixes, two of which are regressions from
recent updates (the 3ware one from 4.1 and the device handler fixes
from 4.2)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
3w-9xxx: don't unmap bounce buffered commands
scsi_dh: Use the correct module name when loading device handler
libiscsi: Fix iscsi_check_transport_timeouts possible infinite loop
The LinkSprite pcDuino2 board is almost identical to the older
LinkSprite pcDuino1 board according to the schematic pdf files.
So we just include the existing "sun4i-a10-pcduino.dts" file and
make the necessary adjustments.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pcDuino1 board does not use any power switches at all for its
two USB host ports and the VBUS pins are always connected to 5V.
The pcDuino2 board uses the RT9701GB power switch for its single
USB host port, but the USB_EN pin (PD2) is pulled up with a 10K
resistor. So that the USB power is still enabled by default,
resulting in the same behaviour as pcDuino1 if nobody touches
the PD2 pin. This minor difference is going to be handled in a
follow-up patch, introducing a separate dts file for pcDuino2.
The primary reason for this fix is that the current dts file
unnecessarily meddles with the PH3 and PH6 pins. But the PH6 pin
is available on the Arduino-compatible expansion header and may
have a better use for other purposes. This patch fixes the
problem and now the PH6 pin can be used with the GPIO sysfs
interface. Tested on a pcDuino2 board with a multimeter:
echo 230 > /sys/class/gpio/export
echo "out" > /sys/class/gpio/gpio230/direction
echo 0 > /sys/class/gpio/gpio230/value
echo 1 > /sys/class/gpio/gpio230/value
USB still works as expected too.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the otg/drc usb controller on the Bananapi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sun7i-a20-bananapi.dts doesn't contain regulator nodes for the AXP209 PMU
driver, so add them to allow for voltage-scaling with cpufreq-dt. Also
add board-specific OPP to use slightly higher voltages at lower
frequencies since Kevin Hilman reported that not all BananaPi boards run
stable at the default voltages inherited by sun7i-a20.dtsi.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Very careless bug earler in 4.3-rc, now fixed :-)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=qdcM
-----END PGP SIGNATURE-----
Merge tag 'md/4.3-rc4-fix' of git://neil.brown.name/md
Pull md bugfix from Neil Brown:
"One bug fix for raid1/raid10.
Very careless bug earler in 4.3-rc, now fixed :-)"
* tag 'md/4.3-rc4-fix' of git://neil.brown.name/md:
crash in md-raid1 and md-raid10 due to incorrect list manipulation
In former commits, asynchronous transactions are supported for physical
controls. This commit adds a pair of MIDI ports for them.
This driver already adds diferrent number of ALSA MIDI ports for physical
MIDI ports, and the number of in/out ports are different. As seeing as
'amidi' program in alsa-utils package, a pair of in/out MIDI ports is
expected with the same name. Therefore, this commit adds a pair of new
ports to the first.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In previous commit, asynchronous transaction for incoming MIDI messages
from physical controls is supported. The physical controls may be
controlled by receiving MIDI messages at a certain address.
This commit supports asynchronous transaction for this purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Digi 00x series has two types of model; rack and console. The console
models have physical controls. The model can transmit control messages.
These control messages are transferred by asynchronous transactions to
registered address.
This commit supports the asynchronous transaction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds MIDI functionality to capture/playback MIDI messages
from/to physical MIDI ports. These messages are transferred in isochronous
packets.
When no substreams request AMDTP streams to run, this driver starts the
streams at current sampling rate. When other substreams start at different
sampling rate, the streams are stopped temporarily, then start again at
requested sampling rate. This operation can generate missing MIDI bytes,
thus it's preferable to start PCM substreams at favorite sampling rate in
advance.
Digi 002/003 console also has a set of MIDI port for physical controls.
These ports are added in later commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In Digi 002/003 protocol, MIDI messages are transferred in the last data
channel of data blocks. Although this data channel has a label of 0x80,
it's not fully MIDI conformant data channel especially because the Counter
field always zero independently of included MIDI bytes. The 4th byte of
the data channel in LSB tells the number of included MIDI bytes. This byte
also includes the number of MIDI port. Therefore, the data format in this
data channel is:
* 1st: 0x80 as label
* 2nd: MIDI bytes
* 3rd: 0 or MIDI bytes
* 4th: the number of MIDI byte and the number of MIDI port
This commit adds support of MIDI messages in data block processing layer.
Like AM824 data format, this data channel has a capability to transfer
more MIDI messages than the capability of phisical MIDI bus. Therefore, a
throttle for data rate is required to prevent devices' internal buffer to
overflow.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Original code for 'DoubleOhThree' encoding was written with '__u8' type,
while the type is usually used to export something to userspace.
This commit replaces the type with 'u8'.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch enables interrupt transfer mode for MIDI ports on newer
Boss/Roland devices such as the GT-100/001 which support interrupt
transfer on both IN and OUT MIDI endpoints. Previously this wasn't being
enabled for these devices as the code was specifically looking for the
scenario where the IN endpoint supported interrupt transfer and the OUT
endpoint was bulk transfer. Newer devices support interrupt transfer for
both endpoints.
This has been tested on Boss devices GT-001, BR-80 and JS-8 and Roland
VS-20.
It would benefit from some regresison testing with other devices if
possible.
Signed-off-by: Keith A. Milner <maillist@superlative.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In firewire-lib, isochronous packet streaming is stopped when detecting
wrong value for FMT field of CIP headers. Although this is appropriate
to IEC 61883-1 and 6, some BeBoB based devices with vendors' customization
use invalid value to FMT field of CIP headers in the beginning of
streaming.
$ journalctl
snd-bebob fw1.0: Detect unexpected protocol: 01000000 8000ffff
I got this log with M-Audio FireWire 1814. In this line, the value of FMT
field is 0x00, while it should be 0x10 in usual AMDTP.
Except for the beginning, these devices continue to transfer packets with
valid value for FMT field, except for the beginning. Therefore, in this
case, firewire-lib should continue to process packets. The former
implementation of firewire-lib performs it.
This commit loosens the handling of wrong value, to continue packet
processing in the case.
Fixes: 414ba022a5 ('ALSA: firewire-lib: add support arbitrary value for fmt/fdf fields in CIP header')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The structures of type snd_bebob_clock_spec, snd_bebob_rate_spec,
snd_bebob_meter_spec, and snd_bebob_spec are never modified after they are
initialized. Make them all const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some regulators can supply multiple voltages. To take changing voltages
into account, the scale needs to be calculated on every read access.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix some indentation issues and separate returns by empty lines (IIO
style). Also rename the channel mask in _read_raw() to mask.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A return variable is not required in _write_raw(), and dropping it reduces
complexity, as well.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Make use of ARRAY_SIZE to prevent buffer issues.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The regulator framework requests to balance regulator_enable() calls with
regulator_disable() calls. To meet this requirement, set channels to 0 on
remove, which implies a regulator_disable() call in case that channel was
enabled.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This device simply uses its Vcc as reference voltage, so the same scale
applies for all channels. Also offset doesn't appear to be different for
any channel. Represent this by switching these two attributes to
info_mask_shared_by_type.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
0° Kelvin is actually −273.15°C, not -272.15°C. Fix the temperature offset.
Also improve the comment explaining the calculation.
Reported-by: Janusz Użycki <j.uzycki@elpromaelectronics.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Marek Vasut <marex@denx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Previous offset wasn't applied in the correct order and invalid.
This patchset fixes this issue, and also has the correct scale value
applied to the offset.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Before recent TCP listener patches, we were updating listener
sk->sk_rxhash before the cloning of master socket.
children sk_rxhash was therefore correct after the normal 3WHS.
But with lockless listener, we no longer dirty/change listener sk_rxhash
as it would be racy.
We need to correctly update the child sk_rxhash, otherwise first data
packet wont hit correct cpu if RFS is used.
Fixes: 079096f103 ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a clone of commit 2ab957492d ("ip_forward: Drop frames with
attached skb->sk") for ipv6.
This commit has exactly the same reasons as the above mentioned commit,
namely to prevent panics during netfilter reload or a misconfigured stack.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRE point-to-point interfaces should also support ipv6 multicast. Setting
up default multicast routes on interface creation was forgotten. Add it.
Bugzilla: <https://bugzilla.kernel.org/show_bug.cgi?id=103231>
Cc: Julien Muchembled <jm@jmuchemb.eu>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Nicolas Dumazet <ndumazet@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: push switchdev prepare phase in FDB ops
This patchset pushes the switchdev prepare phase for the FDB add and del
operations down to the DSA drivers. Currently only mv88e6xxx is affected.
Since the dump requires a bit of refactoring in the driver, it'll come in a
future patchset.
Changes in v2:
* forward declare switchdev structs instead of fixing the dsa.h include.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency with the FDB add operation, propagate the
switchdev_obj_port_fdb structure in the DSA drivers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the prepare phase is pushed down to the DSA drivers, propagate
it to the port_fdb_add function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Push the prepare phase for FDB operations down to the DSA drivers, with
a new port_fdb_prepare function. Currently only mv88e6xxx is affected.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-10-08
Here's another set of Bluetooth & 802.15.4 patches for the 4.4 kernel.
802.15.4:
- Many improvements & fixes to the mrf24j40 driver
- Fixes and cleanups to nl802154, mac802154 & ieee802154 code
Bluetooth:
- New chipset support in btmrvl driver
- Fixes & cleanups to btbcm, btmrvl, bpa10x & btintel drivers
- Support for vendor specific diagnostic data through common API
- Cleanups to the 6lowpan code
- New events & message types for monitor channel
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring 4-tuple RSS hsahing for UDP
[E.g., by using `ethtool -N <interface> rx-flow-hash udp4 sdfn']
on a 57710/57711 adapter would cause it to assert as HW does not
support such a configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: couple of fixes
Just a couple of small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When calculating the shift needed in order to access a bit array element
in a byte, we should multiply the index by the element size and not
assume it is fixed at 2-bits.
Fixes: 93c1edb27f ("mlxsw: Introduce Mellanox switch driver core")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we have two processes to do:
P1#: ifconfig eth0 down; which will call bnx2_close, then will
, and set Null to stats_blk
P2#: ifconfig eth0; which will call bnx2_get_stats64, it will
use stats_blk.
In one case:
--P1#-- --P2#--
stats_blk(no null)
bnx2_free_mem
->bp->stats_blk = NULL
GET_64BIT_NET_STATS
then it will cause 'NULL Pointer' Problem.
it is as well with 'ethtool -S ethx'.
Allocate the statistics block at probe time so that this problem is
impossible
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
selinux needs few changes to accommodate fact that SYNACK messages
can be attached to a request socket, lacking sk_security pointer
(Only syncookies are still attached to a TCP_LISTEN socket)
Adds a new sk_listener() helper, and use it in selinux and sch_fq
Fixes: ca6fb06518 ("tcp: attach SYNACK messages to request sockets instead of listener")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported by: kernel test robot <ying.huang@linux.intel.com>
Cc: Paul Moore <paul@paul-moore.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Eric Paris <eparis@parisplace.org>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
