md_reload_sb is too simplistic and it explicitly needs to determine
the changes made by the writing node. However, there are multiple areas
where a simple reload could fail.
Instead, read the superblock of one of the "good" rdevs and update
the necessary information:
- read the superblock into a newly allocated page, by temporarily
swapping out rdev->sb_page and calling ->load_super.
- if that fails return
- if it succeeds, call check_sb_changes
1. iterates over list of active devices and checks the matching
dev_roles[] value.
If that is 'faulty', the device must be marked as faulty
- call md_error to mark the device as faulty. Make sure
not to set CHANGE_DEVS and wakeup mddev->thread or else
it would initiate a resync process, which is the responsibility
of the "primary" node.
- clear the Blocked bit
- Call remove_and_add_spares() to hot remove the device.
If the device is 'spare':
- call remove_and_add_spares() to get the number of spares
added in this operation.
- Reduce mddev->degraded to mark the array as not degraded.
2. reset recovery_cp
- read the rest of the rdevs to update recovery_offset. If recovery_offset
is equal to MaxSector, call spare_active() to set it In_sync
This required that recovery_offset be initialized to MaxSector, as
opposed to zero so as to communicate the end of sync for a rdev.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
remove_and_add_spares() checks for all devices to activate spare.
Change it to activate a specific device if a non-null rdev
argument is passed.
remove_and_add_spares() can be used to activate spares in
slot_store() as well.
For hot_remove_disk(), check if rdev->raid_disk == -1 before
calling remove_and_add_spares()
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
When the suspended_area is deleted, the suspended processes
must be woken up in order to complete their I/O.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Previously, BITMAP_NEEDS_SYNC message is sent when the resyc
aborts, but it could abort for different reasons, and not all
of reasons require another node to take over the resync ownship.
It is better make BITMAP_NEEDS_SYNC message only be sent when
the node is leaving cluster with dirty bitmap. And we also need
to ensure dlm connection is ok.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Suspending the entire device for resync could take too long. Resync
in small chunks.
cluster's resync window (32M) is maintained in r1conf as
cluster_sync_low and cluster_sync_high and processed in
raid1's sync_request(). If the current resync is outside the cluster
resync window:
1. Set the cluster_sync_low to curr_resync_completed.
2. Check if the sync will fit in the new window, if not issue a
wait_barrier() and set cluster_sync_low to sector_nr.
3. Set cluster_sync_high to cluster_sync_low + resync_window.
4. Send a message to all nodes so they may add it in their suspension
list.
bitmap_cond_end_sync is modified to allow to force a sync inorder
to get the curr_resync_completed uptodate with the sector passed.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Add BITMAP_MAJOR_CLUSTERED as 5, in order to prevent older kernels
to assemble a clustered device.
In order to maximize compatibility, the major version is set to
BITMAP_MAJOR_CLUSTERED *only* if the bitmap is clustered.
Added MD_FEATURE_CLUSTERED in order to return error for older
kernels which would assemble MD even if the bitmap is corrupted.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
process_suspend_info - which handles the RESYNCING request - must not
reply until all writes which were initiated before the request arrived,
have completed.
As a by-product, all process_* functions now take mddev as their
first arguement making it uniform.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
In an effort to get more useful out of "possible memory
allocation deadlock" messages, print the size of the
requested allocation, and dump the stack if the xfs error
level is tuned high.
The stack dump is implemented in define_xfs_printk_level()
for error levels >= LOGLEVEL_ERR, partly because it
seems generically useful, and also because kmem.c has
no knowledge of xfs error level tunables or other such bits,
it's very kmem-specific.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The gcc undefined behavior sanitizer caught this; surely
any sane memcpy implementation will no-op if size == 0,
but behavior with a *src of NULL is technically undefined
(declared nonnull), so avoid it here.
We are actually in this situation frequently via
xlog_commit_record(), because:
struct xfs_log_iovec reg = {
.i_addr = NULL,
.i_len = 0,
.i_type = XLOG_REG_TYPE_COMMIT,
};
Reported-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The total field from struct xfs_alloc_arg is a bit of an unknown
commodity. It is documented as the total block requirement for the
transaction and is used in this manner from most call sites by virtue of
passing the total block reservation of the transaction associated with
an allocation. Several xfs_bmapi_write() callers pass hardcoded values
of 0 or 1 for the total block requirement, which is a historical oddity
without any clear reasoning.
The xfs_iomap_write_direct() caller, for example, passes 0 for the total
block requirement. This has been determined to cause problems in the
form of ABBA deadlocks of AGF buffers due to incorrect AG selection in
the block allocator. Specifically, the xfs_alloc_space_available()
function incorrectly selects an AG that doesn't actually have sufficient
space for the allocation. This occurs because the args.total field is 0
and thus the remaining free space check on the AG doesn't actually
consider the size of the allocation request. This locks the AGF buffer,
the allocation attempt proceeds and ultimately fails (in
xfs_alloc_fix_minleft()), and xfs_alloc_vexent() moves on to the next
AG. In turn, this can lead to incorrect AG locking order (if the
allocator wraps around, attempting to lock AG 0 after acquiring AG N)
and thus deadlock if racing with another operation. This problem has
been reproduced via generic/299 on smallish (1GB) ramdisk test devices.
To avoid this problem, replace the undocumented hardcoded total
parameters from the iomap and utility callers to pass the block
reservation used for the associated transaction. This is consistent with
other xfs_bmapi_write() callers throughout XFS. The assumption is that
the total field allows the selection of an AG that can handle the entire
operation rather than simply the allocation/range being requested (e.g.,
resulting btree splits, etc.). This addresses the aforementioned
generic/299 hang by ensuring AG selection only occurs when the
allocation can be satisfied by the AG.
Reported-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Currently, we depends on Linux XATTR value for on disk
definition. Which causes trouble on other platforms and
maybe also if this value was to change.
Fix it by creating a custom definition independent from
those in Linux (although with the same values), so it is OK
with the be16 fields used for holding these attributes.
This patch reflects a change in xfsprogs.
Signed-off-by: Jan Tulak <jtulak@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Remove a hard dependency of Linux XATTR_LIST_MAX value by using
a prefixed version. This patch reflects the same change in xfsprogs.
Signed-off-by: Jan Tulak <jtulak@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Just fix two typos in code comments.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Add a tracepoint in xfs_zero_eof() to facilitate tracking and debugging
EOF zeroing events. This has proven useful in the context of other
direct I/O tracepoints to ensure EOF zeroing occurs within appropriate
file ranges.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
XFS supports and typically allows concurrent asynchronous direct I/O
submission to a single file. One exception to the rule is that file
extending dio writes that start beyond the current EOF (e.g.,
potentially create a hole at EOF) require exclusive I/O access to the
file. This is because such writes must zero any pre-existing blocks
beyond EOF that are exposed by virtue of now residing within EOF as a
result of the write about to be submitted.
Before EOF zeroing can occur, the current file i_size must be stabilized
to avoid data corruption. In this scenario, XFS upgrades the iolock to
exclude any further I/O submission, waits on in-flight I/O to complete
to ensure i_size is up to date (i_size is updated on dio write
completion) and restarts the various checks against the state of the
file. The problem is that this protection sequence is triggered only
when the iolock is currently held shared. While this is true for async
dio in most cases, the caller may upgrade the lock in advance based on
arbitrary circumstances with respect to EOF zeroing. For example, the
iolock is always acquired exclusively if the start offset is not block
aligned. This means that even though the iolock is already held
exclusive for such I/Os, pending I/O is not drained and thus EOF zeroing
can occur based on an unstable i_size.
This problem has been reproduced as guest data corruption in virtual
machines with file-backed qcow2 virtual disks hosted on an XFS
filesystem. The virtual disks must be configured with aio=native mode
and the must not be truncated out to the maximum file size (as some virt
managers will do).
Update xfs_file_aio_write_checks() to unconditionally drain in-flight
dio before EOF zeroing can occur. Rather than trigger the wait based on
iolock state, use a new flag and upgrade the iolock when necessary. Note
that this results in a full restart of the inode checks even when the
iolock was already held exclusive when technically it is only required
to recheck i_size. This should be a rare enough occurrence that it is
preferable to keep the code simple rather than create an alternate
restart jump target.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Since the onset of v5 superblocks, the LSN of the last modification has
been included in a variety of on-disk data structures. This LSN is used
to provide log recovery ordering guarantees (e.g., to ensure an older
log recovery item is not replayed over a newer target data structure).
While this works correctly from the point a filesystem is formatted and
mounted, userspace tools have some problematic behaviors that defeat
this mechanism. For example, xfs_repair historically zeroes out the log
unconditionally (regardless of whether corruption is detected). If this
occurs, the LSN of the filesystem is reset and the log is now in a
problematic state with respect to on-disk metadata structures that might
have a larger LSN. Until either the log catches up to the highest
previously used metadata LSN or each affected data structure is modified
and written out without incident (which resets the metadata LSN), log
recovery is susceptible to filesystem corruption.
This problem is ultimately addressed and repaired in the associated
userspace tools. The kernel is still responsible to detect the problem
and notify the user that something is wrong. Check the superblock LSN at
mount time and fail the mount if it is invalid. From that point on,
trigger verifier failure on any metadata I/O where an invalid LSN is
detected. This results in a filesystem shutdown and guarantees that we
do not log metadata changes with invalid LSNs on disk. Since this is a
known issue with a known recovery path, present a warning to instruct
the user how to recover.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
This patch adds comm name and pid to warning messages printed by
kmem_alloc(), kmem_zone_alloc() and xfs_buf_allocate_memory().
This will help telling which memory allocations (e.g. kernel worker
threads, OOM victim tasks, neither) are stalling because these functions
are passing __GFP_NOWARN which suppresses not only backtrace but comm name
and pid.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
A local format symlink inode is converted to extent format when an
extended attribute is set on an inode as part of the attribute fork
creation. This means a block is allocated, the local symlink target name
is copied to the block and the block is logged. Currently,
xfs_bmap_local_to_extents() handles logging the remote block data based
on the size of the data fork prior to the conversion. This is not
correct on v5 superblock filesystems, which add an additional header to
remote symlink blocks that is nonexistent in local format inodes.
As a result, the full length of the remote symlink block content is not
logged. This can lead to corruption should a crash occur and log
recovery replay this transaction.
Since a callout is already used to initialize the new remote symlink
block, update the local-to-extents conversion mechanism to make the
callout also responsible for logging the block. It is already required
to set the log buffer type and format the block appropriately based on
the superblock version. This ensures the remote symlink is always logged
correctly. Note that xfs_bmap_local_to_extents() is only called for
symlinks so there are no other callouts that require modification.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The iomap codepath (via get_blocks()) acquires and release the inode
lock in the case of a direct write that requires block allocation. This
is because xfs_iomap_write_direct() allocates a transaction, which means
the ilock must be dropped and reacquired after the transaction is
allocated and reserved.
xfs_iomap_write_direct() invokes xfs_iomap_eof_align_last_fsb() before
the transaction is created and thus before the ilock is reacquired. This
can lead to calls to xfs_iread_extents() and reads of the in-core extent
list without any synchronization (via xfs_bmap_eof() and
xfs_bmap_last_extent()). xfs_iread_extents() assert fails if the ilock
is not held, but this is not currently seen in practice as the current
callers had already invoked xfs_bmapi_read().
What has been seen in practice are reports of crashes down in the
xfs_bmap_eof() codepath on direct writes due to seemingly bogus pointer
references from xfs_iext_get_ext(). While an explicit reproducer is not
currently available to confirm the cause of the problem, crash analysis
and code inspection from David Jeffrey had identified the insufficient
locking.
xfs_iomap_eof_align_last_fsb() is called from other contexts with the
inode lock already held, so we cannot acquire it therein.
__xfs_get_blocks() acquires and drops the ilock with variable flags to
cover the event that the extent list must be read in. The common case is
that __xfs_get_blocks() acquires the shared ilock. To provide locking
around the last extent alignment call without adding more lock cycles to
the dio path, update xfs_iomap_write_direct() to expect the shared ilock
held on entry and do the extent alignment under its protection. Demote
the lock, if necessary, from __xfs_get_blocks() and push the
xfs_qm_dqattach() call outside of the shared lock critical section.
Also, add an assert to document that the extent list is always expected
to be present in this path. Otherwise, we risk a call to
xfs_iread_extents() while under the shared ilock. This is safe as all
current callers have executed an xfs_bmapi_read() call under the current
iolock context.
Reported-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
We need to properly identify whether a hugepage is an explicit or
a transparent hugepage in follow_huge_addr(). We used to depend
on hugepage shift argument to do that. But in some case that can
result in wrong results. For ex:
On finding a transparent hugepage we set hugepage shift to PMD_SHIFT.
But we can end up clearing the thp pte, via pmdp_huge_get_and_clear.
We do prevent reusing the pfn page via the usage of
kick_all_cpus_sync(). But that happens after we updated the pte to 0.
Hence in follow_huge_addr() we can find hugepage shift set, but transparent
huge page check fail for a thp pte.
NOTE: We fixed a variant of this race against thp split in commit
691e95fd73
("powerpc/mm/thp: Make page table walk safe against thp split/collapse")
Without this patch, we may hit the BUG_ON(flags & FOLL_GET) in
follow_page_mask occasionally.
In the long term, we may want to switch ppc64 64k page size config to
enable CONFIG_ARCH_WANT_GENERAL_HUGETLB
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
After commit e2b3d202d1
("powerpc: Switch 16GB and 16MB explicit hugepages to a
different page table format"), we don't need to support
is_hugepd() for 64K page size.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When I ran xfstest/073 case, the remount process was blocked to wait
transactions to be zero. I found there was a io error happened, and
the setfilesize transaction was not released properly. We should add
the changes to cancel the io error in this case.
Reproduction steps:
1. dd if=/dev/zero of=xfs1.img bs=1M count=2048
2. mkfs.xfs xfs1.img
3. losetup -f ./xfs1.img /dev/loop0
4. mount -t xfs /dev/loop0 /home/test_dir/
5. mkdir /home/test_dir/test
6. mkfs.xfs -dfile,name=image,size=2g
7. mount -t xfs -o loop image /home/test_dir/test
8. cp a file bigger than 2g to /home/test_dir/test
9. mount -t xfs -o remount,ro /home/test_dir/test
[ dchinner: moved io error detection to xfs_setfilesize_ioend() after
transaction context restoration. ]
Signed-off-by: Zhao Hongjiang <zhaohongjiang@huawei.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Nothing too crazy here, a couple of regression fixes + runpm/fbcon
race fix.
* 'linux-4.3' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/bios: fix OF loading
drm/nouveau/fbcon: take runpm reference when userspace has an open fd
drm/nouveau/nouveau: Disable AGP for SiS 761
drm/nouveau/display: allow up to 16k width/height for fermi+
drm/nouveau/bios: translate devinit pri/sec i2c bus to internal identifiers
Currently OF bios load fails for a few reasons:
- checksum failure
- bios size too small
- no PCIR header
- bios length not a multiple of 4
In this change, we resolve all of the above by ignoring any checksum
failures (since OF VBIOS tends not to have a checksum), and faking the
PCIR data when loading from OF.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We need to do this in order to prevent accesses to the device while it's
powered down. Userspace may have an mmap of the fb, and there's no good
way (that I know of) to prevent it from touching the device otherwise.
This fixes some nasty races between runpm and plymouth on some systems,
which result in the GPU getting very upset and hanging the boot.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
SiS 761 chipset does not support AGP cards but has AGP capability (for
the onboard video). At least PC Chips A31G board using this chipset has
an AGP-like AGPro slot that's wired to the PCI bus. Enabling AGP will
fail (GPU lockup and software fbcon, X11 hangs).
Add support for matching just the host bridge in nvkm_device_agp_quirks
and add entry for SiS 761 with mode 0 (AGP disabled).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Actviate HDMI output of the RCar DU (and LVDS while we are here).
Enable the HDMI encoder chip found on Lager/Koelsch boards.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the PCIe controller and clock for the Porter board.
This patch is analogous to the commit 485f3ce67c ("ARM: shmobile:
henninger: Enable PCIe Controller & PCIe bus clock") as there are no
differences between the boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Porter board dependent part of the QSPI device node.
Add device nodes for Spansion S25FL512S SPI flash and the MTD partitions
on it.
This patch is mostly analogous to the commit f59838d448 ("ARM:
shmobile: henninger: add QSPI DT support") as there are no differences
between the boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Some newer Intel Skylake based Dell laptops with Win8 precision touchpad
fail when initial feature reports are fetched from it. Below is an example
output with some additional debug included:
i2c_hid i2c-DLL0704:01: Fetching the HID descriptor
i2c_hid i2c-DLL0704:01: __i2c_hid_command: cmd=20 00
i2c_hid i2c-DLL0704:01: HID Descriptor: 1e 00 00 01 99 02 21 00 24 ...
...
i2c_hid i2c-DLL0704:01: i2c_hid_get_report
i2c_hid i2c-DLL0704:01: __i2c_hid_command: cmd=22 00 38 02 23 00
i2c_hid i2c-DLL0704:01: report (len=4): 04 00 08 05
i2c_hid i2c-DLL0704:01: report id 13
i2c_hid i2c-DLL0704:01: i2c_hid_get_report
i2c_hid i2c-DLL0704:01: __i2c_hid_command: cmd=22 00 3d 02 23 00
i2c_hid i2c-DLL0704:01: failed to retrieve report from device.
i2c_hid i2c-DLL0704:01: report id 7
i2c_hid i2c-DLL0704:01: i2c_hid_get_report
i2c_hid i2c-DLL0704:01: __i2c_hid_command: cmd=22 00 37 02 23 00
i2c_hid i2c-DLL0704:01: report (len=259): 03 01 07 fc 28 fe 84 40 ...
i2c_hid i2c-DLL0704:01: report id 4
i2c_hid i2c-DLL0704:01: i2c_hid_get_report
i2c_hid i2c-DLL0704:01: __i2c_hid_command: cmd=22 00 34 02 23 00
We manage to fetch few reports but then the touchpad dies:
i2c_designware i2c_designware.1: i2c_dw_handle_tx_abort: lost arbitration
i2c_hid i2c-DLL0704:01: failed to retrieve report from device.
it eventually pulls the whole I2C bus low:
i2c_designware i2c_designware.1: controller timed out
i2c_hid i2c-DLL0704:01: failed to set a report to device.
Fix this by preventing initial feature report retrieval for Win8 devices.
Instead we fetch reports as needed in mt_feature_mapping(). This prevents
fetching reports which might cause problems with the device in question.
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The kernel NMI watchdog acts as both a hardlockup and softlockup detector.
However, the kernel parameter nmi_watchdog can only enable or disable the
hardlockup detector. Clarify that in the documentation.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
On some places, people could use Private: to tag the private fields
of an struct. So, be case-insensitive when parsing "private:"
meta-tag.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The #kernelnewbies irc channel is no longer hosted on
irc.openprojects.net but on irc.oftc.net.
Removed pointer to different regional servers since oftc already uses
geo-IP load balancing.
The "description" quoted from the website no longer exists,
therefore removed the reference, quotes and carets.
The paragraph also contains a pointer to the kernelnewbies.org website.
Therefore changing the title to:
"Kernel Newbies IRC Channel and Website."
Signed-off-by: Richard Sailer <richard@weltraumpflege.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This patch fix spelling typos in Documentation/virtual/kvm.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
bc is mentioned lower in a dedicated section.
Yet it is useful to have all dependencies listed in
"Current Minimal Requirements" section.
Signed-off-by: Benoit Lemarchand <benoit.lemarchand@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
In apply_slack(), find_last_bit() is applied to a bitmask consisting
of precisely BITS_PER_LONG bits. Since mask is non-zero, we might as
well eliminate the function call and use __fls() directly. On x86_64,
this shaves 23 bytes of the only caller, mod_timer().
This also gets rid of Coverity CID 1192106, but that is a false
positive: Coverity is not aware that mask != 0 implies that
find_last_bit will not return BITS_PER_LONG.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/1443771931-6284-1-git-send-email-linux@rasmusvillemoes.dk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The probe of a mtd device can fail when a partition parser returns
error. The failure due to partition parsing can be quite mysterious when
multiple partitioning schemes are compiled in and any of them can fail
the probe.
Add debug prints which show what parsers were tried and what they
returned.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
asm/ioctls.h contains definition for termios, not just the _IO* macros.
This error was found with a tool in development used to generate
automated pretty-printing functions for ioctl decoding in strace.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1444141657-14898-2-git-send-email-gabriel@lse.epita.fr
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We have to define internally used function as static, otherwise the following
warning will be generated:
arch/x86/kernel/apic/io_apic.c:532:6: warning: no previous prototype for 'eoi_ioapic_pin' [-Wmissing-prototypes]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jiang Liu <jiang.liu@linux.intel.com>
Link: http://lkml.kernel.org/r/1444400685-98611-1-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The following warning is issued on unfixed code.
arch/x86/platform/intel-mid/intel-mid.c:64:22: warning: symbol 'intel_mid_ops' was not declared. Should it be static?
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: http://lkml.kernel.org/r/1444400741-98669-1-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch is the next step toward per-fs xfs stats. The patch makes
the show and clear routines able to handle any stats structure
associated with a kobject.
Instead of a single global xfsstats structure, add kobject and a pointer
to a per-cpu struct xfsstats. Modify the macros that manipulate the stats
accordingly: XFS_STATS_INC, XFS_STATS_DEC, and XFS_STATS_ADD now access
xfsstats->xs_stats.
The sysfs functions need to get from the kobject back to the xfsstats
structure which contains it, and pass the pointer to the ->xs_stats
percpu structure into the show & clear routines.
Signed-off-by: Bill O'Donnell <billodo@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
As a part of the series to move xfs global stats from procfs to sysfs,
this patch consolidates the sysfs ops functions and removes redundancy.
Signed-off-by: Bill O'Donnell <billodo@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
As a part of the work to move xfs global stats from procfs to sysfs,
this patch removes the now unused procfs code that was xfs stat specific.
Signed-off-by: Bill O'Donnell <billodo@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
