[ Upstream commit 1be79d89b7 ]
The TC filters used in the test do not work with veth devices because the
outer Ethertype is 802.1Q and not IPv4. The test passes with mlxsw
netdevs since the hardware always looks at "The first Ethertype that
does not point to either: VLAN, CNTAG or configurable Ethertype".
Fix this by matching on the VLAN ID instead, but on the ingress side.
The reason why this is not performed at egress is explained in the
commit cited below.
Fixes: 541ad323db ("selftests: forwarding: gre_multipath: Update next-hop statistics match criteria")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Tested-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efa7b79f67 ]
The test did not enable IPv4 forwarding during its setup phase, which
causes the test to fail on machines where IPv4 forwarding is disabled.
Fixes: 54818c4c4b ("selftests: forwarding: Test multipath tunneling")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Tested-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bba18318e7 ]
PPv2's XLGMAC can wait for 3 idle frames before triggering a link up
event. This can cause the link to be stuck low when there's traffic on
the interface, so disable this feature.
Fixes: 4bb0432628 ("net: mvpp2: phylink support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12185dfe44 ]
The following scenario was encountered during testing of logical
partition mobility on pseries partitions with bonded ibmvnic
adapters in LACP mode.
1. Driver receives a signal that the device has been
swapped, and it needs to reset to initialize the new
device.
2. Driver reports loss of carrier and begins initialization.
3. Bonding driver receives NETDEV_CHANGE notifier and checks
the slave's current speed and duplex settings. Because these
are unknown at the time, the bond sets its link state to
BOND_LINK_FAIL and handles the speed update, clearing
AD_PORT_LACP_ENABLE.
4. Driver finishes recovery and reports that the carrier is on.
5. Bond receives a new notification and checks the speed again.
The speeds are valid but miimon has not altered the link
state yet. AD_PORT_LACP_ENABLE remains off.
Because the slave's link state is still BOND_LINK_FAIL,
no further port checks are made when it recovers. Though
the slave devices are operational and have valid speed
and duplex settings, the bond will not send LACPDU's. The
simplest fix I can see is to force another speed check
in bond_miimon_commit. This way the bond will update
AD_PORT_LACP_ENABLE if needed when transitioning from
BOND_LINK_FAIL to BOND_LINK_UP.
CC: Jarod Wilson <jarod@redhat.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8eee4135a ]
"sendmsg6: rewrite IP & port (C)" fails on s390, because the code in
sendmsg_v6_prog() assumes that (ctx->user_ip6[0] & 0xFFFF) refers to
leading IPv6 address digits, which is not the case on big-endian
machines.
Since checking bitwise operations doesn't seem to be the point of the
test, replace two short comparisons with a single int comparison.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8dd26dff00 ]
DPCM uses snd_soc_dapm_dai_get_connected_widgets to build a
list of the widgets connected to a specific front end DAI so it
can search through this list for available back end DAIs. The
custom_stop_condition was added to is_connected_ep to facilitate this
list not containing more widgets than is necessary. Doing so both
speeds up the DPCM handling as less widgets need to be searched and
avoids issues with CODEC to CODEC links as these would be confused
with back end DAIs if they appeared in the list of available widgets.
custom_stop_condition was implemented by aborting the graph walk
when the condition is triggered, however there is an issue with this
approach. Whilst walking the graph is_connected_ep should update the
endpoints cache on each widget, if the walk is aborted the number
of attached end points is unknown for that sub-graph. When the stop
condition triggered, the original patch ignored the triggering widget
and returned zero connected end points; a later patch updated this
to set the triggering widget's cache to 1 and return that. Both of
these approaches result in inaccurate values being stored in various
end point caches as the values propagate back through the graph,
which can result in later issues with widgets powering/not powering
unexpectedly.
As the original goal was to reduce the size of the widget list passed
to the DPCM code, the simplest solution is to limit the functionality
of the custom_stop_condition to the widget list. This means the rest
of the graph will still be processed resulting in correct end point
caches, but only widgets up to the stop condition will be added to the
returned widget list.
Fixes: 6742064aef ("ASoC: dapm: support user-defined stop condition in dai_get_connected_widgets")
Fixes: 5fdd022c20 ("ASoC: dpcm: play nice with CODEC<->CODEC links")
Fixes: 09464974ea ("ASoC: dapm: Fix to return correct path list in is_connected_ep.")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20190718084333.15598-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15a78ba184 ]
In compat_do_replace(), a temporary buffer is allocated through vmalloc()
to hold entries copied from the user space. The buffer address is firstly
saved to 'newinfo->entries', and later on assigned to 'entries_tmp'. Then
the entries in this temporary buffer is copied to the internal kernel
structure through compat_copy_entries(). If this copy process fails,
compat_do_replace() should be terminated. However, the allocated temporary
buffer is not freed on this path, leading to a memory leak.
To fix the bug, free the buffer before returning from compat_do_replace().
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8bea8a5e5 ]
Because CONFIG_OF defined for MIPS, cacheinfo attempts to fill information
from DT, ignoring data filled by architecture routine. This leads to error
reported
cacheinfo: Unable to detect cache hierarchy for CPU 0
Way to fix this provided in
commit fac5148257 ("drivers: base: cacheinfo: fix x86 with
CONFIG_OF enabled")
Utilize same mechanism to report that cacheinfo set by architecture
specific function
Signed-off-by: Vladimir Kondratiev <vladimir.kondratiev@linux.intel.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a07e332453 ]
i8253 clocksource needs a free running timer. This could only
be used, if i8253 clockevent is set up as periodic.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65f11c7278 ]
Enable force feedback for the Thrustmaster Dual Trigger 2 in 1 Rumble Force
gamepad. Compared to other Thrustmaster devices, left and right rumble
motors here are swapped.
Signed-off-by: Ilya Trukhanov <lahvuun@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 60208a2672 upstream.
When mmc-pwrseq property is passed mmc_pwrseq_alloc() can return
-EPROBE_DEFER because driver for power sequence provider is not probed
yet. Do not show error message when this situation happens.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 405b93eb76 ]
The current ARFS code relies on certain fields to be set in the SKB
(e.g. transport_header) and extracts IP addresses and ports by custom
code that parses the packet. The necessary SKB fields, however, are not
always set at that point, which leads to an out-of-bounds access. Use
skb_flow_dissect_flow_keys() to get the necessary information reliably,
fix the out-of-bounds access and reuse the code.
Fixes: 18c908e477 ("net/mlx5e: Add accelerated RFS support")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 466df6eb4a ]
Only support changing tx/rx pause frame setting if the net device
is the vport group manager.
Fixes: 3c2d18ef22 ("net/mlx5e: Support ethtool get/set_pauseparam")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3a0233ddec ]
At this point nr_frags has been incremented but the frag does not yet
have a page assigned so freeing the skb results in a crash. Reset
nr_frags before freeing the skb to prevent this.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8874ecae29 ]
We set the field 'addr_trial_end' to 'jiffies', instead of the current
value 0, at the moment the node address is initialized. This guarantees
we don't inadvertently enter an address trial period when the node
address is explicitly set by the user.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 227f2f030e ]
We should also enable team's vlan tx offload in hw_enc_features,
pass the vlan packets to the slave devices with vlan tci, let the
slave handle vlan tunneling offload implementation.
Fixes: 3268e5cb49 ("team: Advertise tunneling offload features")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a1794de8b9 ]
As the annotation says in sctp_do_8_2_transport_strike():
"If the transport error count is greater than the pf_retrans
threshold, and less than pathmaxrtx ..."
It should be transport->error_count checked with pathmaxrxt,
instead of asoc->pf_retrans.
Fixes: 5aa93bcf66 ("sctp: Implement quick failover draft from tsvwg")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6d5afe2039 ]
If the stream outq is not empty, need to kfree nstr_list.
Fixes: d570a59c5b ("sctp: only allow the out stream reset when the stream outq is empty")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 48ec7014c5 ]
In mlx4_en_config_rss_steer(), 'rss_map->indir_qp' is allocated through
kzalloc(). After that, mlx4_qp_alloc() is invoked to configure RSS
indirection. However, if mlx4_qp_alloc() fails, the allocated
'rss_map->indir_qp' is not deallocated, leading to a memory leak bug.
To fix the above issue, add the 'qp_alloc_err' label to free
'rss_map->indir_qp'.
Fixes: 4931c6ef04 ("net/mlx4_en: Optimized single ring steering")
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d595b03de2 ]
As commit 30d8177e8a ("bonding: Always enable vlan tx offload")
said, we should always enable bonding's vlan tx offload, pass the
vlan packets to the slave devices with vlan tci, let them to handle
vlan implementation.
Now if encapsulation protocols like VXLAN is used, skb->encapsulation
may be set, then the packet is passed to vlan device which based on
bonding device. However in netif_skb_features(), the check of
hw_enc_features:
if (skb->encapsulation)
features &= dev->hw_enc_features;
clears NETIF_F_HW_VLAN_CTAG_TX/NETIF_F_HW_VLAN_STAG_TX. This results
in same issue in commit 30d8177e8a like this:
vlan_dev_hard_start_xmit
-->dev_queue_xmit
-->validate_xmit_skb
-->netif_skb_features //NETIF_F_HW_VLAN_CTAG_TX is cleared
-->validate_xmit_vlan
-->__vlan_hwaccel_push_inside //skb->tci is cleared
...
--> bond_start_xmit
--> bond_xmit_hash //BOND_XMIT_POLICY_ENCAP34
--> __skb_flow_dissect // nhoff point to IP header
--> case htons(ETH_P_8021Q)
// skb_vlan_tag_present is false, so
vlan = __skb_header_pointer(skb, nhoff, sizeof(_vlan),
//vlan point to ip header wrongly
Fixes: b2a103e6d0 ("bonding: convert to ndo_fix_features")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4a4d2d372f ]
Commit 04f05230c5 ("bnx2x: Remove configured vlans as
part of unload sequence."), introduced a regression in driver
that as a part of VF's reload flow, VLANs created on the VF
doesn't get re-configured in hardware as vlan metadata/info
was not getting cleared for the VFs which causes vlan PING to stop.
This patch clears the vlan metadata/info so that VLANs gets
re-configured back in the hardware in VF's reload flow and
PING/traffic continues for VLANs created over the VFs.
Fixes: 04f05230c5 ("bnx2x: Remove configured vlans as part of unload sequence.")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Sudarsana Kalluru <skalluru@marvell.com>
Signed-off-by: Shahed Shaikh <shshaikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24d2c52174 upstream.
The function is only called from another __init function, so
it should be moved to .init too.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49e6979e7e upstream.
trackpoint_detect() should be static inline while
CONFIG_MOUSE_PS2_TRACKPOINT is not set, otherwise, we build fails:
drivers/input/mouse/alps.o: In function `trackpoint_detect':
alps.c:(.text+0x8e00): multiple definition of `trackpoint_detect'
drivers/input/mouse/psmouse-base.o:psmouse-base.c:(.text+0x1b50): first defined here
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 55e3d9224b ("Input: psmouse - allow disabing certain protocol extensions")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 656c8e9cc1 upstream.
Change ct id hash calculation to only use invariants.
Currently the ct id hash calculation is based on some fields that can
change in the lifetime on a conntrack entry in some corner cases. The
current hash uses the whole tuple which contains an hlist pointer which
will change when the conntrack is placed on the dying list resulting in
a ct id change.
This patch also removes the reply-side tuple and extension pointer from
the hash calculation so that the ct id will will not change from
initialization until confirmation.
Fixes: 3c79107631 ("netfilter: ctnetlink: don't use conntrack/expect object addresses as id")
Signed-off-by: Dirk Morris <dmorris@metaloft.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6143d10d2 upstream.
The initial support for dynamic ftrace trampolines in modules made use
of an indirect branch which loaded its target from the beginning of
a special section (e71a4e1beb ("arm64: ftrace: add support for far
branches to dynamic ftrace")). Since no instructions were being patched,
no cache maintenance was needed. However, later in be0f272bfc ("arm64:
ftrace: emit ftrace-mod.o contents through code") this code was reworked
to output the trampoline instructions directly into the PLT entry but,
unfortunately, the necessary cache maintenance was overlooked.
Add a call to __flush_icache_range() after writing the new trampoline
instructions but before patching in the branch to the trampoline.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: James Morse <james.morse@arm.com>
Cc: <stable@vger.kernel.org>
Fixes: be0f272bfc ("arm64: ftrace: emit ftrace-mod.o contents through code")
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcb44433bb upstream.
Storage devices which report supporting discard commands like
WRITE_SAME_16 with unmap, but reject discard commands sent to the
storage device. This is a clear storage firmware bug but it doesn't
change the fact that should a program cause discards to be sent to a
multipath device layered on this buggy storage, all paths can end up
failed at the same time from the discards, causing possible I/O loss.
The first discard to a path will fail with Illegal Request, Invalid
field in cdb, e.g.:
kernel: sd 8:0:8:19: [sdfn] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
kernel: sd 8:0:8:19: [sdfn] tag#0 Sense Key : Illegal Request [current]
kernel: sd 8:0:8:19: [sdfn] tag#0 Add. Sense: Invalid field in cdb
kernel: sd 8:0:8:19: [sdfn] tag#0 CDB: Write same(16) 93 08 00 00 00 00 00 a0 08 00 00 00 80 00 00 00
kernel: blk_update_request: critical target error, dev sdfn, sector 10487808
The SCSI layer converts this to the BLK_STS_TARGET error number, the sd
device disables its support for discard on this path, and because of the
BLK_STS_TARGET error multipath fails the discard without failing any
path or retrying down a different path. But subsequent discards can
cause path failures. Any discards sent to the path which already failed
a discard ends up failing with EIO from blk_cloned_rq_check_limits with
an "over max size limit" error since the discard limit was set to 0 by
the sd driver for the path. As the error is EIO, this now fails the
path and multipath tries to send the discard down the next path. This
cycle continues as discards are sent until all paths fail.
Fix this by training DM core to disable DISCARD if the underlying
storage already did so.
Also, fix branching in dm_done() and clone_endio() to reflect the
mutually exclussive nature of the IO operations in question.
Cc: stable@vger.kernel.org
Reported-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[Salvatore Bonaccorso: backported to 4.19: Adjust for context changes in
drivers/md/dm-core.h]
Signed-off-by: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0e062ebb3 upstream.
One more CFL ID added to spec.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180803232721.20038-1-rodrigo.vivi@intel.com
Signed-off-by: Wan Yusof, Wan Fahim AsqalaniX <wan.fahim.asqalanix.wan.yusof@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6caf0be40a upstream.
On Motorola Mapphone devices such as Droid 4 there are five USB ports
that do not use the same layout as Gobi 1K/2K/etc devices listed in
qcserial.c. So we should use qcaux.c or option.c as noted by
Dan Williams <dan.j.williams@intel.com>.
As the Motorola USB serial ports have an interrupt endpoint as shown
with lsusb -v, we should use option.c instead of qcaux.c as pointed out
by Johan Hovold <johan@kernel.org>.
The ff/ff/ff interfaces seem to always be UARTs on Motorola devices.
For the other interfaces, class 0x0a (CDC Data) should not in general
be added as they are typically part of a multi-interface function as
noted earlier by Bjørn Mork <bjorn@mork.no>.
However, looking at the Motorola mapphone kernel code, the mdm6600 0x0a
class is only used for flashing the modem firmware, and there are no
other interfaces. So I've added that too with more details below as it
works just fine.
The ttyUSB ports on Droid 4 are:
ttyUSB0 DIAG, CQDM-capable
ttyUSB1 MUX or NMEA, no response
ttyUSB2 MUX or NMEA, no response
ttyUSB3 TCMD
ttyUSB4 AT-capable
The ttyUSB0 is detected as QCDM capable by ModemManager. I think
it's only used for debugging with ModemManager --debug for sending
custom AT commands though. ModemManager already can manage data
connection using the USB QMI ports that are already handled by the
qmi_wwan.c driver.
To enable the MUX or NMEA ports, it seems that something needs to be
done additionally to enable them, maybe via the DIAG or TCMD port.
It might be just a NVRAM setting somewhere, but I have no idea what
NVRAM settings may need changing for that.
The TCMD port seems to be a Motorola custom protocol for testing
the modem and to configure it's NVRAM and seems to work just fine
based on a quick test with a minimal tcmdrw tool I wrote.
The voice modem AT-capable port seems to provide only partial
support, and no PM support compared to the TS 27.010 based UART
wired directly to the modem.
The UARTs added with this change are the same product IDs as the
Motorola Mapphone Android Linux kernel mdm6600_id_table. I don't
have any mdm9600 based devices, so I have only tested these on
mdm6600 based droid 4.
Then for the class 0x0a (CDC Data) mode, the Motorola Mapphone Android
Linux kernel driver moto_flashqsc.c just seems to change the
port->bulk_out_size to 8K from the default. And is only used for
flashing the modem firmware it seems.
I've verified that flashing the modem with signed firmware works just
fine with the option driver after manually toggling the GPIO pins, so
I've added droid 4 modem flashing mode to the option driver. I've not
added the other devices listed in moto_flashqsc.c in case they really
need different port->bulk_out_size. Those can be added as they get
tested to work for flashing the modem.
After this patch the output of /sys/kernel/debug/usb/devices has
the following for normal 22b8:2a70 mode including the related qmi_wwan
interfaces:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22b8 ProdID=2a70 Rev= 0.00
S: Manufacturer=Motorola, Incorporated
S: Product=Flash MZ600
C:* #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=8a(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=8b(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=8c(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=08(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=8d(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=09(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
In 22b8:900e "qc_dload" mode the device shows up as:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22b8 ProdID=900e Rev= 0.00
S: Manufacturer=Motorola, Incorporated
S: Product=Flash MZ600
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
And in 22b8:4281 "ram_downloader" mode the device shows up as:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22b8 ProdID=4281 Rev= 0.00
S: Manufacturer=Motorola, Incorporated
S: Product=Flash MZ600
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=fc Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Lars Melin <larsm17@gmail.com>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5dac665cf4 upstream.
Since the role_store() uses strncmp(), it's possible to refer
out-of-memory if the sysfs data size is smaller than strlen("host").
This patch fixes it by using sysfs_streq() instead of strncmp().
Fixes: cc995c9ec1 ("usb: gadget: udc: renesas_usb3: add support for usb role swap")
Cc: <stable@vger.kernel.org> # v4.12+
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 303911cfc5 upstream.
The syzbot fuzzer has found two (!) races in the USB character device
registration and deregistration routines. This patch fixes the races.
The first race results from the fact that usb_deregister_dev() sets
usb_minors[intf->minor] to NULL before calling device_destroy() on the
class device. This leaves a window during which another thread can
allocate the same minor number but will encounter a duplicate name
error when it tries to register its own class device. A typical error
message in the system log would look like:
sysfs: cannot create duplicate filename '/class/usbmisc/ldusb0'
The patch fixes this race by destroying the class device first.
The second race is in usb_register_dev(). When that routine runs, it
first allocates a minor number, then drops minor_rwsem, and then
creates the class device. If the device creation fails, the minor
number is deallocated and the whole routine returns an error. But
during the time while minor_rwsem was dropped, there is a window in
which the minor number is allocated and so another thread can
successfully open the device file. Typically this results in
use-after-free errors or invalid accesses when the other thread closes
its open file reference, because the kernel then tries to release
resources that were already deallocated when usb_register_dev()
failed. The patch fixes this race by keeping minor_rwsem locked
throughout the entire routine.
Reported-and-tested-by: syzbot+30cf45ebfe0b0c4847a1@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1908121607590.1659-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9ddd50911 upstream.
The max9611 driver reads the die temperature at probe time to validate
the communication channel. Use the actual read value to perform the test
instead of the read function return value, which was mistakenly used so
far.
The temperature reading test was only successful because the 0 return
value is in the range of supported temperatures.
Fixes: 69780a3bbc ("iio: adc: Add Maxim max9611 ADC driver")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e2a589a3f upstream.
`dt3k_ns_to_timer()` determines the prescaler and divisor to use to
produce a desired timing period. It is influenced by a rounding mode
and can round the divisor up, down, or to the nearest value. However,
the code for rounding up currently does the same as rounding down! Fix
ir by using the `DIV_ROUND_UP()` macro to calculate the divisor when
rounding up.
Also, change the types of the `divider`, `base` and `prescale` variables
from `int` to `unsigned int` to avoid mixing signed and unsigned types
in the calculations.
Also fix a typo in a nearby comment: "improvment" => "improvement".
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190812120814.21188-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4d98bc3fc upstream.
In `dt3k_ns_to_timer()` the following lines near the end of the function
result in a signed integer overflow:
prescale = 15;
base = timer_base * (1 << prescale);
divider = 65535;
*nanosec = divider * base;
(`divider`, `base` and `prescale` are type `int`, `timer_base` and
`*nanosec` are type `unsigned int`. The value of `timer_base` will be
either 50 or 100.)
The main reason for the overflow is that the calculation for `base` is
completely wrong. It should be:
base = timer_base * (prescale + 1);
which matches an earlier instance of this calculation in the same
function.
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20190812111517.26803-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5eeaf10eec upstream.
Since commit commit 328e566479 ("KVM: arm/arm64: vgic: Defer
touching GICH_VMCR to vcpu_load/put"), we leave ICH_VMCR_EL2 (or
its GICv2 equivalent) loaded as long as we can, only syncing it
back when we're scheduled out.
There is a small snag with that though: kvm_vgic_vcpu_pending_irq(),
which is indirectly called from kvm_vcpu_check_block(), needs to
evaluate the guest's view of ICC_PMR_EL1. At the point were we
call kvm_vcpu_check_block(), the vcpu is still loaded, and whatever
changes to PMR is not visible in memory until we do a vcpu_put().
Things go really south if the guest does the following:
mov x0, #0 // or any small value masking interrupts
msr ICC_PMR_EL1, x0
[vcpu preempted, then rescheduled, VMCR sampled]
mov x0, #ff // allow all interrupts
msr ICC_PMR_EL1, x0
wfi // traps to EL2, so samping of VMCR
[interrupt arrives just after WFI]
Here, the hypervisor's view of PMR is zero, while the guest has enabled
its interrupts. kvm_vgic_vcpu_pending_irq() will then say that no
interrupts are pending (despite an interrupt being received) and we'll
block for no reason. If the guest doesn't have a periodic interrupt
firing once it has blocked, it will stay there forever.
To avoid this unfortuante situation, let's resync VMCR from
kvm_arch_vcpu_blocking(), ensuring that a following kvm_vcpu_check_block()
will observe the latest value of PMR.
This has been found by booting an arm64 Linux guest with the pseudo NMI
feature, and thus using interrupt priorities to mask interrupts instead
of the usual PSTATE masking.
Cc: stable@vger.kernel.org # 4.12
Fixes: 328e566479 ("KVM: arm/arm64: vgic: Defer touching GICH_VMCR to vcpu_load/put")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d584a3c85 upstream.
When fall-through warnings was enabled by default, commit d93512ef0f0e
("Makefile: Globally enable fall-through warning"), the following
warnings was starting to show up:
In file included from ../arch/arm64/include/asm/kvm_emulate.h:19,
from ../arch/arm64/kvm/regmap.c:13:
../arch/arm64/kvm/regmap.c: In function ‘vcpu_write_spsr32’:
../arch/arm64/include/asm/kvm_hyp.h:31:3: warning: this statement may fall
through [-Wimplicit-fallthrough=]
asm volatile(ALTERNATIVE(__msr_s(r##nvh, "%x0"), \
^~~
../arch/arm64/include/asm/kvm_hyp.h:46:31: note: in expansion of macro ‘write_sysreg_elx’
#define write_sysreg_el1(v,r) write_sysreg_elx(v, r, _EL1, _EL12)
^~~~~~~~~~~~~~~~
../arch/arm64/kvm/regmap.c:180:3: note: in expansion of macro ‘write_sysreg_el1’
write_sysreg_el1(v, SYS_SPSR);
^~~~~~~~~~~~~~~~
../arch/arm64/kvm/regmap.c:181:2: note: here
case KVM_SPSR_ABT:
^~~~
In file included from ../arch/arm64/include/asm/cputype.h:132,
from ../arch/arm64/include/asm/cache.h:8,
from ../include/linux/cache.h:6,
from ../include/linux/printk.h:9,
from ../include/linux/kernel.h:15,
from ../include/asm-generic/bug.h:18,
from ../arch/arm64/include/asm/bug.h:26,
from ../include/linux/bug.h:5,
from ../include/linux/mmdebug.h:5,
from ../include/linux/mm.h:9,
from ../arch/arm64/kvm/regmap.c:11:
../arch/arm64/include/asm/sysreg.h:837:2: warning: this statement may fall
through [-Wimplicit-fallthrough=]
asm volatile("msr " __stringify(r) ", %x0" \
^~~
../arch/arm64/kvm/regmap.c:182:3: note: in expansion of macro ‘write_sysreg’
write_sysreg(v, spsr_abt);
^~~~~~~~~~~~
../arch/arm64/kvm/regmap.c:183:2: note: here
case KVM_SPSR_UND:
^~~~
Rework to add a 'break;' in the swich-case since it didn't have that,
leading to an interresting set of bugs.
Cc: stable@vger.kernel.org # v4.17+
Fixes: a892819560 ("KVM: arm64: Prepare to handle deferred save/restore of 32-bit registers")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
[maz: reworked commit message, fixed stable range]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cbedfe1134 ]
Commit d66acc39c7 ("bitops: Optimise get_order()") introduced a
compilation warning because "rx_frag_size" is an "ushort" while
PAGE_SHIFT here is 16.
The commit changed the get_order() to be a multi-line macro where
compilers insist to check all statements in the macro even when
__builtin_constant_p(rx_frag_size) will return false as "rx_frag_size"
is a module parameter.
In file included from ./arch/powerpc/include/asm/page_64.h:107,
from ./arch/powerpc/include/asm/page.h:242,
from ./arch/powerpc/include/asm/mmu.h:132,
from ./arch/powerpc/include/asm/lppaca.h:47,
from ./arch/powerpc/include/asm/paca.h:17,
from ./arch/powerpc/include/asm/current.h:13,
from ./include/linux/thread_info.h:21,
from ./arch/powerpc/include/asm/processor.h:39,
from ./include/linux/prefetch.h:15,
from drivers/net/ethernet/emulex/benet/be_main.c:14:
drivers/net/ethernet/emulex/benet/be_main.c: In function 'be_rx_cqs_create':
./include/asm-generic/getorder.h:54:9: warning: comparison is always
true due to limited range of data type [-Wtype-limits]
(((n) < (1UL << PAGE_SHIFT)) ? 0 : \
^
drivers/net/ethernet/emulex/benet/be_main.c:3138:33: note: in expansion
of macro 'get_order'
adapter->big_page_size = (1 << get_order(rx_frag_size)) * PAGE_SIZE;
^~~~~~~~~
Fix it by moving all of this multi-line macro into a proper function,
and killing __get_order() off.
[akpm@linux-foundation.org: remove __get_order() altogether]
[cai@lca.pw: v2]
Link: http://lkml.kernel.org/r/1564000166-31428-1-git-send-email-cai@lca.pw
Link: http://lkml.kernel.org/r/1563914986-26502-1-git-send-email-cai@lca.pw
Fixes: d66acc39c7 ("bitops: Optimise get_order()")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Jakub Jelinek <jakub@redhat.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Bill Wendling <morbo@google.com>
Cc: James Y Knight <jyknight@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7bc36e3ce9 ]
Fixes gcc '-Wunused-but-set-variable' warning:
fs/ocfs2/xattr.c: In function ocfs2_xattr_bucket_find:
fs/ocfs2/xattr.c:3828:6: warning: variable last_hash set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Link: http://lkml.kernel.org/r/20190716132110.34836-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df9576def0 ]
When running ltp's oom test with kmemleak enabled, the below warning was
triggerred since kernel detects __GFP_NOFAIL & ~__GFP_DIRECT_RECLAIM is
passed in:
WARNING: CPU: 105 PID: 2138 at mm/page_alloc.c:4608 __alloc_pages_nodemask+0x1c31/0x1d50
Modules linked in: loop dax_pmem dax_pmem_core ip_tables x_tables xfs virtio_net net_failover virtio_blk failover ata_generic virtio_pci virtio_ring virtio libata
CPU: 105 PID: 2138 Comm: oom01 Not tainted 5.2.0-next-20190710+ #7
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.10.2-0-g5f4c7b1-prebuilt.qemu-project.org 04/01/2014
RIP: 0010:__alloc_pages_nodemask+0x1c31/0x1d50
...
kmemleak_alloc+0x4e/0xb0
kmem_cache_alloc+0x2a7/0x3e0
mempool_alloc_slab+0x2d/0x40
mempool_alloc+0x118/0x2b0
bio_alloc_bioset+0x19d/0x350
get_swap_bio+0x80/0x230
__swap_writepage+0x5ff/0xb20
The mempool_alloc_slab() clears __GFP_DIRECT_RECLAIM, however kmemleak
has __GFP_NOFAIL set all the time due to d9570ee3bd ("kmemleak:
allow to coexist with fault injection"). But, it doesn't make any sense
to have __GFP_NOFAIL and ~__GFP_DIRECT_RECLAIM specified at the same
time.
According to the discussion on the mailing list, the commit should be
reverted for short term solution. Catalin Marinas would follow up with
a better solution for longer term.
The failure rate of kmemleak metadata allocation may increase in some
circumstances, but this should be expected side effect.
Link: http://lkml.kernel.org/r/1563299431-111710-1-git-send-email-yang.shi@linux.alibaba.com
Fixes: d9570ee3bd ("kmemleak: allow to coexist with fault injection")
Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Qian Cai <cai@lca.pw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bbbab097a ]
Currently the retry counter is not being decremented, leading to a
potential infinite spin if the scalar_reads don't change state.
Addresses-Coverity: ("Infinite loop")
Fixes: 280e54c9f6 ("drm/exynos: scaler: Reset hardware before starting the operation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ca7ad6c77 ]
add_gpu_components() adds found GPU nodes from the DT to the match list,
regardless of the status of the nodes. This is a problem, because if the
nodes are disabled, they should not be on the match list because they will
not be matched. This prevents display from initing if a GPU node is
defined, but it's status is disabled.
Fix this by checking the node's status before adding it to the match list.
Fixes: dc3ea265b8 (drm/msm: Drop the gpu binding)
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190626180015.45242-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 770b7d96cf ]
We encountered a use-after-free bug when unloading the driver:
[ 3562.116059] BUG: KASAN: use-after-free in ib_mad_post_receive_mads+0xddc/0xed0 [ib_core]
[ 3562.117233] Read of size 4 at addr ffff8882ca5aa868 by task kworker/u13:2/23862
[ 3562.118385]
[ 3562.119519] CPU: 2 PID: 23862 Comm: kworker/u13:2 Tainted: G OE 5.1.0-for-upstream-dbg-2019-05-19_16-44-30-13 #1
[ 3562.121806] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu2 04/01/2014
[ 3562.123075] Workqueue: ib-comp-unb-wq ib_cq_poll_work [ib_core]
[ 3562.124383] Call Trace:
[ 3562.125640] dump_stack+0x9a/0xeb
[ 3562.126911] print_address_description+0xe3/0x2e0
[ 3562.128223] ? ib_mad_post_receive_mads+0xddc/0xed0 [ib_core]
[ 3562.129545] __kasan_report+0x15c/0x1df
[ 3562.130866] ? ib_mad_post_receive_mads+0xddc/0xed0 [ib_core]
[ 3562.132174] kasan_report+0xe/0x20
[ 3562.133514] ib_mad_post_receive_mads+0xddc/0xed0 [ib_core]
[ 3562.134835] ? find_mad_agent+0xa00/0xa00 [ib_core]
[ 3562.136158] ? qlist_free_all+0x51/0xb0
[ 3562.137498] ? mlx4_ib_sqp_comp_worker+0x1970/0x1970 [mlx4_ib]
[ 3562.138833] ? quarantine_reduce+0x1fa/0x270
[ 3562.140171] ? kasan_unpoison_shadow+0x30/0x40
[ 3562.141522] ib_mad_recv_done+0xdf6/0x3000 [ib_core]
[ 3562.142880] ? _raw_spin_unlock_irqrestore+0x46/0x70
[ 3562.144277] ? ib_mad_send_done+0x1810/0x1810 [ib_core]
[ 3562.145649] ? mlx4_ib_destroy_cq+0x2a0/0x2a0 [mlx4_ib]
[ 3562.147008] ? _raw_spin_unlock_irqrestore+0x46/0x70
[ 3562.148380] ? debug_object_deactivate+0x2b9/0x4a0
[ 3562.149814] __ib_process_cq+0xe2/0x1d0 [ib_core]
[ 3562.151195] ib_cq_poll_work+0x45/0xf0 [ib_core]
[ 3562.152577] process_one_work+0x90c/0x1860
[ 3562.153959] ? pwq_dec_nr_in_flight+0x320/0x320
[ 3562.155320] worker_thread+0x87/0xbb0
[ 3562.156687] ? __kthread_parkme+0xb6/0x180
[ 3562.158058] ? process_one_work+0x1860/0x1860
[ 3562.159429] kthread+0x320/0x3e0
[ 3562.161391] ? kthread_park+0x120/0x120
[ 3562.162744] ret_from_fork+0x24/0x30
...
[ 3562.187615] Freed by task 31682:
[ 3562.188602] save_stack+0x19/0x80
[ 3562.189586] __kasan_slab_free+0x11d/0x160
[ 3562.190571] kfree+0xf5/0x2f0
[ 3562.191552] ib_mad_port_close+0x200/0x380 [ib_core]
[ 3562.192538] ib_mad_remove_device+0xf0/0x230 [ib_core]
[ 3562.193538] remove_client_context+0xa6/0xe0 [ib_core]
[ 3562.194514] disable_device+0x14e/0x260 [ib_core]
[ 3562.195488] __ib_unregister_device+0x79/0x150 [ib_core]
[ 3562.196462] ib_unregister_device+0x21/0x30 [ib_core]
[ 3562.197439] mlx4_ib_remove+0x162/0x690 [mlx4_ib]
[ 3562.198408] mlx4_remove_device+0x204/0x2c0 [mlx4_core]
[ 3562.199381] mlx4_unregister_interface+0x49/0x1d0 [mlx4_core]
[ 3562.200356] mlx4_ib_cleanup+0xc/0x1d [mlx4_ib]
[ 3562.201329] __x64_sys_delete_module+0x2d2/0x400
[ 3562.202288] do_syscall_64+0x95/0x470
[ 3562.203277] entry_SYSCALL_64_after_hwframe+0x49/0xbe
The problem was that the MAD PD was deallocated before the MAD CQ.
There was completion work pending for the CQ when the PD got deallocated.
When the mad completion handling reached procedure
ib_mad_post_receive_mads(), we got a use-after-free bug in the following
line of code in that procedure:
sg_list.lkey = qp_info->port_priv->pd->local_dma_lkey;
(the pd pointer in the above line is no longer valid, because the
pd has been deallocated).
We fix this by allocating the PD before the CQ in procedure
ib_mad_port_open(), and deallocating the PD after freeing the CQ
in procedure ib_mad_port_close().
Since the CQ completion work queue is flushed during ib_free_cq(),
no completions will be pending for that CQ when the PD is later
deallocated.
Note that freeing the CQ before deallocating the PD is the practice
in the ULPs.
Fixes: 4be90bc60d ("IB/mad: Remove ib_get_dma_mr calls")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20190801121449.24973-1-leon@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5366d309a ]
Driver shouldn't allow to use UMR to register a MR when
umr_modify_atomic_disabled is set. Otherwise it will always end up with a
failure in the post send flow which sets the UMR WQE to modify atomic access
right.
Fixes: c8d75a980f ("IB/mlx5: Respect new UMR capabilities")
Signed-off-by: Guy Levi <guyle@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20190731081929.32559-1-leon@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
