commit d17ba0f616 upstream.
Driver does not want to keep packets in Tx queue when link is lost.
But present code only reset NIC to flush them, but does not prevent
queuing new packets. Moreover reset sequence itself could generate
new packets via netconsole and NIC falls into endless reset loop.
This patch wakes Tx queue only when NIC is ready to send packets.
This is proper fix for problem addressed by commit 0f9e980bf5
("e1000e: fix cyclic resets at link up with active tx").
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Tested-by: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit caff422ea8 upstream.
This reverts commit 0f9e980bf5.
That change cased false-positive warning about hardware hang:
e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
e1000e 0000:00:1f.6 eth0: Detected Hardware Unit Hang:
TDH <0>
TDT <1>
next_to_use <1>
next_to_clean <0>
buffer_info[next_to_clean]:
time_stamp <fffba7a7>
next_to_watch <0>
jiffies <fffbb140>
next_to_watch.status <0>
MAC Status <40080080>
PHY Status <7949>
PHY 1000BASE-T Status <0>
PHY Extended Status <3000>
PCI Status <10>
e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
Besides warning everything works fine.
Original issue will be fixed property in following patch.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reported-by: Joseph Yasi <joe.yasi@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203175
Tested-by: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fbd6b25009 upstream.
An earlier patch I sent reduced the stack usage enough to get
below the warning limit, and I could show this was safe, but with
GCC_PLUGIN_STRUCTLEAK_BYREF_ALL, it gets worse again because large stack
variables in the same function no longer overlap:
drivers/staging/rtl8712/rtl871x_ioctl_linux.c: In function 'translate_scan.isra.2':
drivers/staging/rtl8712/rtl871x_ioctl_linux.c:322:1: error: the frame size of 1200 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Split out the largest two blocks in the affected function into two
separate functions and mark those noinline_for_stack.
Fixes: 8c5af16f79 ("staging: rtl8712: reduce stack usage")
Fixes: 81a56f6dcd ("gcc-plugins: structleak: Generalize to all variable types")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a26be06d6d upstream.
The change to mapping V4L2 to MMAL buffers 1:1 didn't handle
the condition we get with raw pixel buffers (eg YUV and RGB)
direct from the camera's stills port. That sends the pixel buffer
and then an empty buffer with the EOS flag set. The EOS buffer
wasn't handled and returned an error up the stack.
Handle the condition correctly by returning it to the component
if streaming, or returning with an error if stopping streaming.
Fixes: 9384167070 ("staging: bcm2835-camera: Remove V4L2/MMAL buffer remapping")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb8e97006d upstream.
Before commit "staging: bcm2835-camera: Remove V4L2/MMAL buffer remapping"
there was a need to ensure that there were sufficient buffers supplied from
the user to cover those being sent to the VPU (always 1).
Now the buffers are linked 1:1 between MMAL and V4L2,
therefore there is no need for that check, and indeed it is wrong
as there is no need to submit all the buffers before starting streaming.
Fixes: 9384167070 ("staging: bcm2835-camera: Remove V4L2/MMAL buffer remapping")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70ec64ccda upstream.
With the recent change to match MMAL and V4L2 buffers there
is a need to wait for all MMAL buffers to be returned during
stop_streaming.
Fixes: 9384167070 ("staging: bcm2835-camera: Remove V4L2/MMAL buffer remapping")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dedab2903 upstream.
The commit "staging: bcm2835-camera: Replace open-coded idr with a struct idr."
replaced an internal implementation of an idr with the standard functions
and a spinlock. idr_alloc(GFP_KERNEL) can sleep whilst calling kmem_cache_alloc
to allocate the new node, but this is not valid whilst in an atomic context
due to the spinlock.
There is no need for this to be a spinlock as a standard mutex is
sufficient.
Fixes: 950fd867c6 ("staging: bcm2835-camera: Replace open-coded idr with a struct idr.")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5555ebbbac upstream.
In the default event case switchdev_work is being leaked because
nothing is queued for work. Fix this by kfree'ing switchdev_work
before returning NOTIFY_DONE.
Addresses-Coverity: ("Resource leak")
Fixes: 44baaa43d7 ("staging: fsl-dpaa2/ethsw: Add Freescale DPAA2 Ethernet Switch driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1287533d3d upstream.
When building BPF code using "clang -target bpf -c", clang does not
define __linux__.
To build BPF IR decoders the include linux/lirc.h is needed which
includes linux/types.h. Currently this workaround is needed:
https://git.linuxtv.org/v4l-utils.git/commit/?id=dd3ff81f58c4e1e6f33765dc61ad33c48ae6bb07
This check might otherwise be useful to stop users from using a non-linux
compiler, but if you're doing that you are going to have a lot more
trouble anyway.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21149/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c2eb5b285 upstream.
The VMCI handle array has an integer overflow in
vmci_handle_arr_append_entry when it tries to expand the array. This can be
triggered from a guest, since the doorbell link hypercall doesn't impose a
limit on the number of doorbell handles that a VM can create in the
hypervisor, and these handles are stored in a handle array.
In this change, we introduce a mandatory max capacity for handle
arrays/lists to avoid excessive memory usage.
Signed-off-by: Vishnu Dasa <vdasa@vmware.com>
Reviewed-by: Adit Ranadive <aditr@vmware.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit feb09b2933 upstream.
This patch follows Alan Stern's recent patch:
"p54: Fix race between disconnect and firmware loading"
that overhauled carl9170 buggy firmware loading and driver
unbinding procedures.
Since the carl9170 code was adapted from p54 it uses the
same functions and is likely to have the same problem, but
it's just that the syzbot hasn't reproduce them (yet).
a summary from the changes (copied from the p54 patch):
* Call usb_driver_release_interface() rather than
device_release_driver().
* Lock udev (the interface's parent) before unbinding the
driver instead of locking udev->parent.
* During the firmware loading process, take a reference
to the USB interface instead of the USB device.
* Don't take an unnecessary reference to the device during
probe (and then don't drop it during disconnect).
and
* Make sure to prevent use-after-free bugs by explicitly
setting the driver context to NULL after signaling the
completion.
Cc: <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1909a671db upstream.
syzkallar found a 32-byte memory leak in a rarely executed error
case. The transaction complete work item was not freed if put_user()
failed when writing the BR_TRANSACTION_COMPLETE to the user command
buffer. Fixed by freeing it before put_user() is called.
Reported-by: syzbot+182ce46596c3f2e1eb24@syzkaller.appspotmail.com
Signed-off-by: Todd Kjos <tkjos@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9e08a0738 upstream.
With CONFIG_LKDTM=y and make OBJCOPY=llvm-objcopy, llvm-objcopy errors:
llvm-objcopy: error: --set-section-flags=.text conflicts with
--rename-section=.text=.rodata
Rather than support setting flags then renaming sections vs renaming
then setting flags, it's simpler to just change both at the same time
via --rename-section. Adding the load flag is required for GNU objcopy
to mark .rodata Type as PROGBITS after the rename.
This can be verified with:
$ readelf -S drivers/misc/lkdtm/rodata_objcopy.o
...
Section Headers:
[Nr] Name Type Address Offset
Size EntSize Flags Link Info Align
...
[ 1] .rodata PROGBITS 0000000000000000 00000040
0000000000000004 0000000000000000 A 0 0 4
...
Which shows that .text is now renamed .rodata, the alloc flag A is set,
the type is PROGBITS, and the section is not flagged as writeable W.
Cc: stable@vger.kernel.org
Link: https://sourceware.org/bugzilla/show_bug.cgi?id=24554
Link: https://github.com/ClangBuiltLinux/linux/issues/448
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Suggested-by: Alan Modra <amodra@gmail.com>
Suggested-by: Jordan Rupprect <rupprecht@google.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c12954965 upstream.
The PixArt OEM mice are known for disconnecting every minute in
runlevel 1 or 3 if they are not always polled. So add quirk
ALWAYS_POLL for this Alienware branded Primax mouse as well.
Daniel Schepler (@dschepler) reported and tested the quirk.
Reference: https://github.com/sriemer/fix-linux-mouse/issues/15
Signed-off-by: Sebastian Parschauer <s.parschauer@gmx.de>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7379e6baed upstream.
The interrupt handler `pci230_interrupt()` causes a null pointer
dereference for a PCI260 card. There is no analog output subdevice for
a PCI260. The `dev->write_subdev` subdevice pointer and therefore the
`s_ao` subdevice pointer variable will be `NULL` for a PCI260. The
following call near the end of the interrupt handler results in the null
pointer dereference for a PCI260:
comedi_handle_events(dev, s_ao);
Fix it by only calling the above function if `s_ao` is valid.
Note that the other uses of `s_ao` in the calls
`pci230_handle_ao_nofifo(dev, s_ao);` and `pci230_handle_ao_fifo(dev,
s_ao);` will never be reached for a PCI260, so they are safe.
Fixes: 39064f2328 ("staging: comedi: amplc_pci230: use comedi_handle_events()")
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8336be66d upstream.
The interrupt handler `dt282x_interrupt()` causes a null pointer
dereference for those supported boards that have no analog output
support. For these boards, `dev->write_subdev` will be `NULL` and
therefore the `s_ao` subdevice pointer variable will be `NULL`. In that
case, the following call near the end of the interrupt handler results
in a null pointer dereference:
comedi_handle_events(dev, s_ao);
Fix it by only calling the above function if `s_ao` is valid.
(There are other uses of `s_ao` by the interrupt handler that may or may
not be reached depending on values of hardware registers. Trust that
they are reliable for now.)
Note:
commit 4f6f009b20 ("staging: comedi: dt282x: use comedi_handle_events()")
propagates an earlier error from
commit f21c74fa4c ("staging: comedi: dt282x: use cfc_handle_events()").
Fixes: 4f6f009b20 ("staging: comedi: dt282x: use comedi_handle_events()")
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2681795b5e upstream.
Writing 4CC commands with tps6598x_write_4cc() already has
a pointer arg, don't reference it when using as arg to
tps6598x_block_write(). Correcting this enforces the constness
of the pointer to propagate to tps6598x_block_write(), so add
the const qualifier there to avoid the warning.
Fixes: 0a4c005bd1 ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers")
Signed-off-by: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05da75fc65 upstream.
Portinfo bit field is 3 bits wide, not 2 bits. This led to
a wrong driver configuration for some tps6598x configurations.
Fixes: 0a4c005bd1 ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers")
Signed-off-by: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2357839c5 upstream.
The old commit 6e4b74e469 ("usb: renesas: fix scheduling in atomic
context bug") fixed an atomic issue by using workqueue for the shdmac
dmaengine driver. However, this has a potential race condition issue
between the work pending and usbhsg_ep_free_request() in gadget mode.
When usbhsg_ep_free_request() is called while pending the queue,
since the work_struct will be freed and then the work handler is
called, kernel panic happens on process_one_work().
To fix the issue, if we could call cancel_work_sync() at somewhere
before the free request, it could be easy. However,
the usbhsg_ep_free_request() is called on atomic (e.g. f_ncm driver
calls free request via gether_disconnect()).
For now, almost all users are having "USB-DMAC" and the DMAengine
driver can be used on atomic. So, this patch adds a workaround for
a race condition to call the DMAengine APIs without the workqueue.
This means we still have TODO on shdmac environment (SH7724), but
since it doesn't have SMP, the race condition might not happen.
Fixes: ab330cf388 ("usb: renesas_usbhs: add support for USB-DMAC")
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfc4fdebc5 upstream.
Use a 10000us AHB idle timeout in dwc2_core_reset() and make it
consistent with the other "wait for AHB master IDLE state" ocurrences.
This fixes a problem for me where dwc2 would not want to initialize when
updating to 4.19 on a MIPS Lantiq VRX200 SoC. dwc2 worked fine with
4.14.
Testing on my board shows that it takes 180us until AHB master IDLE
state is signalled. The very old vendor driver for this SoC (ifxhcd)
used a 1 second timeout.
Use the same timeout that is used everywhere when polling for
GRSTCTL_AHBIDLE instead of using a timeout that "works for one board"
(180us in my case) to have consistent behavior across the dwc2 driver.
Cc: linux-stable <stable@vger.kernel.org> # 4.19+
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d29fcf7078 upstream.
On spin lock release in rx_submit, gether_disconnect get a chance to
run, it makes port_usb NULL, rx_submit access NULL port USB, hence null
pointer crash.
Fixed by releasing the lock in rx_submit after port_usb is used.
Fixes: 2b3d942c48 ("usb ethernet gadget: split out network core")
Cc: <stable@vger.kernel.org>
Signed-off-by: Kiruthika Varadarajan <Kiruthika.Varadarajan@harman.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e41e2257f upstream.
The syzbot fuzzer found a bug in the p54 USB wireless driver. The
issue involves a race between disconnect and the firmware-loader
callback routine, and it has several aspects.
One big problem is that when the firmware can't be loaded, the
callback routine tries to unbind the driver from the USB _device_ (by
calling device_release_driver) instead of from the USB _interface_ to
which it is actually bound (by calling usb_driver_release_interface).
The race involves access to the private data structure. The driver's
disconnect handler waits for a completion that is signalled by the
firmware-loader callback routine. As soon as the completion is
signalled, you have to assume that the private data structure may have
been deallocated by the disconnect handler -- even if the firmware was
loaded without errors. However, the callback routine does access the
private data several times after that point.
Another problem is that, in order to ensure that the USB device
structure hasn't been freed when the callback routine runs, the driver
takes a reference to it. This isn't good enough any more, because now
that the callback routine calls usb_driver_release_interface, it has
to ensure that the interface structure hasn't been freed.
Finally, the driver takes an unnecessary reference to the USB device
structure in the probe function and drops the reference in the
disconnect handler. This extra reference doesn't accomplish anything,
because the USB core already guarantees that a device structure won't
be deallocated while a driver is still bound to any of its interfaces.
To fix these problems, this patch makes the following changes:
Call usb_driver_release_interface() rather than
device_release_driver().
Don't signal the completion until after the important
information has been copied out of the private data structure,
and don't refer to the private data at all thereafter.
Lock udev (the interface's parent) before unbinding the driver
instead of locking udev->parent.
During the firmware loading process, take a reference to the
USB interface instead of the USB device.
Don't take an unnecessary reference to the device during probe
(and then don't drop it during disconnect).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+200d4bb11b23d929335f@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f2640ed7b upstream.
This reverts commit 2e9fe53910.
Reading LSR unconditionally but processing the error flags only if
UART_IIR_RDI bit was set before in IIR may lead to a loss of transmission
error information on UARTs where the transmission error flags are cleared
by a read of LSR. Information are lost in case an error is detected right
before the read of LSR while processing e.g. an UART_IIR_THRI interrupt.
Signed-off-by: Oliver Barta <o.barta89@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: 2e9fe53910 ("serial: 8250: Don't service RX FIFO if interrupts are disabled")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8377eff54 upstream.
This adds the vid:pid of the isodebug v1 isolated JTAG/SWD+UART. Only the
second channel is available for use as a serial port.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@unjo.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63d7ef3610 upstream.
Per the 802.11 specification, vendor IEs are (at minimum) only required
to contain an OUI. A type field is also included in ieee80211.h (struct
ieee80211_vendor_ie) but doesn't appear in the specification. The
remaining fields (subtype, version) are a convention used in WMM
headers.
Thus, we should not reject vendor-specific IEs that have only the
minimum length (3 bytes) -- we should skip over them (since we only want
to match longer IEs, that match either WMM or WPA formats). We can
reject elements that don't have the minimum-required 3 byte OUI.
While we're at it, move the non-standard subtype and version fields into
the WMM structs, to avoid this confusion in the future about generic
"vendor header" attributes.
Fixes: 685c9b7750 ("mwifiex: Abort at too short BSS descriptor element")
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 685c9b7750 upstream.
Currently mwifiex_update_bss_desc_with_ie() implicitly assumes that
the source descriptor entries contain the enough size for each type
and performs copying without checking the source size. This may lead
to read over boundary.
Fix this by putting the source size check in appropriate places.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e88559470 upstream.
Add documentation for Spectre vulnerability and the mitigation mechanisms:
- Explain the problem and risks
- Document the mitigation mechanisms
- Document the command line controls
- Document the sysfs files
Co-developed-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Co-developed-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 993773d11d upstream.
The index to access the threads tls array is controlled by userspace
via syscall: sys_ptrace(), hence leading to a potential exploitation
of the Spectre variant 1 vulnerability.
The index can be controlled from:
ptrace -> arch_ptrace -> do_get_thread_area.
Fix this by sanitizing the user supplied index before using it to access
the p->thread.tls_array.
Signed-off-by: Dianzhang Chen <dianzhangchen0@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1561524630-3642-1-git-send-email-dianzhangchen0@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31a2fbb390 upstream.
The index to access the threads ptrace_bps is controlled by userspace via
syscall: sys_ptrace(), hence leading to a potential exploitation of the
Spectre variant 1 vulnerability.
The index can be controlled from:
ptrace -> arch_ptrace -> ptrace_get_debugreg.
Fix this by sanitizing the user supplied index before using it access
thread->ptrace_bps.
Signed-off-by: Dianzhang Chen <dianzhangchen0@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1561476617-3759-1-git-send-email-dianzhangchen0@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 599ee18f07 upstream.
In commit 292c34c102 ("perf pmu: Fix core PMU alias list for X86
platform"), we fixed the issue of CPU events being aliased to uncore
events.
Fix this same issue for ARM64, since the said commit left the (broken)
behaviour untouched for ARM64.
Signed-off-by: John Garry <john.garry@huawei.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Hendrik Brueckner <brueckner@linux.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Shaokun Zhang <zhangshaokun@hisilicon.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxarm@huawei.com
Cc: stable@vger.kernel.org
Fixes: 292c34c102 ("perf pmu: Fix core PMU alias list for X86 platform")
Link: http://lkml.kernel.org/r/1560521283-73314-2-git-send-email-john.garry@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbc3117d4c upstream.
In reboot tests on several devices we were seeing a "use after free"
when slub_debug or KASAN was enabled. The kernel complained about:
Unable to handle kernel paging request at virtual address 6b6b6c2b
...which is a classic sign of use after free under slub_debug. The
stack crawl in kgdb looked like:
0 test_bit (addr=<optimized out>, nr=<optimized out>)
1 bfq_bfqq_busy (bfqq=<optimized out>)
2 bfq_select_queue (bfqd=<optimized out>)
3 __bfq_dispatch_request (hctx=<optimized out>)
4 bfq_dispatch_request (hctx=<optimized out>)
5 0xc056ef00 in blk_mq_do_dispatch_sched (hctx=0xed249440)
6 0xc056f728 in blk_mq_sched_dispatch_requests (hctx=0xed249440)
7 0xc0568d24 in __blk_mq_run_hw_queue (hctx=0xed249440)
8 0xc0568d94 in blk_mq_run_work_fn (work=<optimized out>)
9 0xc024c5c4 in process_one_work (worker=0xec6d4640, work=0xed249480)
10 0xc024cff4 in worker_thread (__worker=0xec6d4640)
Digging in kgdb, it could be found that, though bfqq looked fine,
bfqq->bic had been freed.
Through further digging, I postulated that perhaps it is illegal to
access a "bic" (AKA an "icq") after bfq_exit_icq() had been called
because the "bic" can be freed at some point in time after this call
is made. I confirmed that there certainly were cases where the exact
crashing code path would access the "bic" after bfq_exit_icq() had
been called. Sspecifically I set the "bfqq->bic" to (void *)0x7 and
saw that the bic was 0x7 at the time of the crash.
To understand a bit more about why this crash was fairly uncommon (I
saw it only once in a few hundred reboots), you can see that much of
the time bfq_exit_icq_fbqq() fully frees the bfqq and thus it can't
access the ->bic anymore. The only case it doesn't is if
bfq_put_queue() sees a reference still held.
However, even in the case when bfqq isn't freed, the crash is still
rare. Why? I tracked what happened to the "bic" after the exit
routine. It doesn't get freed right away. Rather,
put_io_context_active() eventually called put_io_context() which
queued up freeing on a workqueue. The freeing then actually happened
later than that through call_rcu(). Despite all these delays, some
extra debugging showed that all the hoops could be jumped through in
time and the memory could be freed causing the original crash. Phew!
To make a long story short, assuming it truly is illegal to access an
icq after the "exit_icq" callback is finished, this patch is needed.
Cc: stable@vger.kernel.org
Reviewed-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d07a9a4f66 upstream.
Dell headset mode platform with ALC236.
It doesn't recording after system resume from S3.
S3 mode was deep. s2idle was not has this issue.
S3 deep will cut of codec power. So, the register will back to default
after resume back.
This patch will solve this issue.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca95c7bf3d upstream.
Extension Unit (XU) is used to have a compatible layout with
Processing Unit (PU) on UAC1, and the usb-audio driver code assumed it
for parsing the descriptors. Meanwhile, on UAC2, XU became slightly
incompatible with PU; namely, XU has a one-byte bmControls bitmap
while PU has two bytes bmControls bitmap. This incompatibility
results in the read of a wrong address for the last iExtension field,
which ended up with an incorrect string for the mixer element name, as
recently reported for Focusrite Scarlett 18i20 device.
This patch corrects this misalignment by introducing a couple of new
macros and calling them depending on the descriptor type.
Fixes: 23caaf19b1 ("ALSA: usb-mixer: Add support for Audio Class v2.0")
Reported-by: Stefan Sauer <ensonic@hora-obscura.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b09a2ab2ba upstream.
There was a typo at the lower frequency limit for a DVB-C
card, causing the driver to fail while tuning channels at the
VHF range.
https://bugzilla.kernel.org/show_bug.cgi?id=202083
Fixes: f1b1eabff0 ("media: dvb: represent min/max/step/tolerance freqs in Hz")
Reported-by: Ari Kohtamäki <ari.kohtamaki@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa33cdbf3e upstream.
In some cases, using the 'truncate' command to extend a UDF file results
in a mismatch between the length of the file's extents (specifically, due
to incorrect length of the final NOT_ALLOCATED extent) and the information
(file) length. The discrepancy can prevent other operating systems
(i.e., Windows 10) from opening the file.
Two particular errors have been observed when extending a file:
1. The final extent is larger than it should be, having been rounded up
to a multiple of the block size.
B. The final extent is not shorter than it should be, due to not having
been updated when the file's information length was increased.
[JK: simplified udf_do_extend_final_block(), fixed up some types]
Fixes: 2c948b3f86 ("udf: Avoid IO in udf_clear_inode")
CC: stable@vger.kernel.org
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Link: https://lore.kernel.org/r/1561948775-5878-1-git-send-email-steve@digidescorp.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5858bdad4d upstream.
The directory may have been removed when entering
fscrypt_ioctl_set_policy(). If so, the empty_dir() check will return
error for ext4 file system.
ext4_rmdir() sets i_size = 0, then ext4_empty_dir() reports an error
because 'inode->i_size < EXT4_DIR_REC_LEN(1) + EXT4_DIR_REC_LEN(2)'. If
the fs is mounted with errors=panic, it will trigger a panic issue.
Add the check IS_DEADDIR() to fix this problem.
Fixes: 9bd8212f98 ("ext4 crypto: add encryption policy and password salt support")
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Hongjie Fang <hongjiefang@asrmicro.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b962261484 ]
rpc_clnt_add_xprt take a reference to struct rpc_xprt_switch, but forget
to release it before return, may lead to a memory leak.
Signed-off-by: Lin Yi <teroincn@163.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 909105199a ]
We can end up in nfs4_opendata_alloc during task exit, in which case
current->fs has already been cleaned up. This leads to a crash in
current_umask().
Fix this by only setting creation opendata if we are actually doing an open
with O_CREAT. We can drop the check for NULL nfs4_open_createattrs, since
O_CREAT will never be set for the recovery path.
Suggested-by: Trond Myklebust <trondmy@hammerspace.com>
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48620e3416 ]
The comment is correct, but the code ends up moving the bits four
places too far, into the VTUOp field.
Fixes: 11ea809f1a (net: dsa: mv88e6xxx: support 256 databases)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9476274093 ]
Left shifting the signed int value 1 by 31 bits has undefined behaviour
and the shift amount oq_no can be as much as 63. Fix this by using
BIT_ULL(oq_no) instead.
Addresses-Coverity: ("Bad shift operation")
Fixes: f21fb3ed36 ("Add support of Cavium Liquidio ethernet adapters")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f6a862205 ]
A similar fix to Patch "ip_tunnel: allow not to count pkts on tstats by
setting skb's dev to NULL" is also needed by ip6_tunnel.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74b67efa8d ]
The copy_from_user() function returns the number of bytes remaining
to be copied but we want to return a negative error code. Otherwise
the callers treat it as a successful copy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190618131843.GA29463@mwanda
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf18cecca9 ]
Some transceivers may comply with SFF-8472 even though they do not
implement the Digital Diagnostic Monitoring (DDM) interface described in
the spec. The existence of such area is specified by the 6th bit of byte
92, set to 1 if implemented.
Currently, without checking this bit, bnx2x fails trying to read sfp
module's EEPROM with the follow message:
ethtool -m enP5p1s0f1
Cannot get Module EEPROM data: Input/output error
Because it fails to read the additional 256 bytes in which it is assumed
to exist the DDM data.
This issue was noticed using a Mellanox Passive DAC PN 01FT738. The EEPROM
data was confirmed by Mellanox as correct and similar to other Passive
DACs from other manufacturers.
Signed-off-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Acked-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9642fa73d0 ]
Stopping external metadata arrays during resync/recovery causes
retries, loop of interrupting and starting reconstruction, until it
hit at good moment to stop completely. While these retries
curr_mark_cnt can be small- especially on HDD drives, so subtraction
result can be smaller than 0. However it is casted to uint without
checking. As a result of it the status bar in /proc/mdstat while stopping
is strange (it jumps between 0% and 99%).
The real problem occurs here after commit 72deb455b5 ("block: remove
CONFIG_LBDAF"). Sector_div() macro has been changed, now the
divisor is casted to uint32. For db = -8 the divisior(db/32-1) becomes 0.
Check if db value can be really counted and replace these macro by
div64_u64() inline.
Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0e370b95a ]
We don't have a reproducible error case, yet our BSP team suggested that
the mmc_switch_status() command in mmc_select_hs400() should come after
the callback into the driver completing HS400 setup. It makes sense to
me because we want the status of a fully setup HS400, so it will
increase the reliability of the mmc_switch_status() command.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: ba6c7ac3a2 ("mmc: core: more fine-grained hooks for HS400 tuning")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
