This patch implements a generic CPU idle driver for ARM64 machines.
It relies on the DT idle states infrastructure to initialize idle
states count and respective parameters. Current code assumes the driver
is managing idle states on all possible CPUs but can be easily
generalized to support heterogenous systems and build cpumasks at
runtime using MIDRs or DT cpu nodes compatible properties.
Suspend back-ends (eg PSCI) must register a suspend initializer with
the CPU idle driver so that the suspend backend call can be detected,
and the driver code can call the back-end infrastructure to complete the
suspend backend initialization.
Idle state index 0 is always initialized as a simple wfi state, ie always
considered present and functional on all ARM64 platforms.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Conflicts:
drivers/cpuidle/Kconfig
drivers/cpuidle/Makefile
This patch implements the cpu_suspend cpu operations method through
the PSCI CPU_SUSPEND API. The PSCI implementation translates the idle state
index passed by the cpu_suspend core call into a valid PSCI state according to
the PSCI states initialized at boot by the PSCI suspend backend.
Entry point is set to cpu_resume physical address, that represents the
default kernel execution address following a CPU reset.
Idle state indices missing a DT node description are initialized to power
state standby WFI so that if called by the idle driver they provide the
default behaviour.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
On most common ARM systems, the low-power states a CPU can be put into are
not discoverable in HW and require device tree bindings to describe
the respective power domains, power down protocol and idle states parameters.
In order to enable DT based idle states and configure idle drivers, this
patch implements the bulk infrastructure required to parse the device tree
idle states bindings and initialize the corresponding CPUidle driver states
data.
Code that initializes idle states checks the CPU idle driver cpumask so
that multiple CPU idle drivers can be initialized through it in the
kernel. The CPU idle driver cpumask defines which idle states should be
considered valid for the driver, ie idle states that are valid on a set
of cpus the idle driver manages.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Conflicts:
drivers/cpuidle/Kconfig
The primary aim of this patchset is to remove the pgprot_default and
prot_sect_default global variables and rely strictly on predefined
values. The original goal was to be able to run SMP kernels on UP
hardware by not setting the Shareability bit. However, it is unlikely to
see UP ARMv8 hardware and even if we do, the Shareability bit is no
longer assumed to disable cacheable accesses.
A side effect is that the device mappings now have the Shareability
attribute set. The hardware, however, should ignore it since Device
accesses are always Outer Shareable.
Following the removal of the two global variables, there is some PROT_*
macro reshuffling and cleanup, including the __PAGE_* macros (replaced
by PAGE_*).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
(cherry picked from commit a501e32430)
Signed-off-by: Mark Brown <broonie@linaro.org>
Conflicts:
arch/arm64/include/asm/io.h
arch/arm64/include/asm/pgtable.h
Add support for early IO or memory mappings which are needed before the
normal ioremap() is usable. This also adds fixmap support for permanent
fixed mappings such as that used by the earlyprintk device register
region.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(cherry picked from commit bf4b558eba)
Signed-off-by: Mark Brown <broonie@linaro.org>
Conflicts:
arch/arm64/Kconfig
arch/arm64/mm/ioremap.c
This patch creates a generic implementation of early_ioremap() support
based on the existing x86 implementation. early_ioremp() is useful for
early boot code which needs to temporarily map I/O or memory regions
before normal mapping functions such as ioremap() are available.
Some architectures have optional MMU. In the no-MMU case, the remap
functions simply return the passed in physical address and the unmap
functions do nothing.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(cherry picked from commit 9e5c33d7ae)
Signed-off-by: Mark Brown <broonie@linaro.org>
Conflicts:
mm/Kconfig
mm/Makefile
Many architectures provide an asm/fixmap.h which defines support for
compile-time 'special' virtual mappings which need to be made before
paging_init() has run. This support is also used for early ioremap on
x86. Much of this support is identical across the architectures. This
patch consolidates all of the common bits into asm-generic/fixmap.h
which is intended to be included from arch/*/include/asm/fixmap.h.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jonas Bonn <jonas.bonn@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(cherry picked from commit d57c33c5da)
Signed-off-by: Mark Brown <broonie@linaro.org>
When calling our low-level barrier macros directly, we can often suffice
with more relaxed behaviour than the default "all accesses, full system"
option.
This patch updates the users of dsb() to specify the option which they
actually require.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 98f7685ee6)
Signed-off-by: Mark Brown <broonie@linaro.org>
Conflicts:
arch/arm64/kvm/sys_regs.c
Some users of xchg() don't bother using the return value, which results
in a compiler warning like the following (from kgdb):
In file included from linux/arch/arm64/include/asm/atomic.h:27:0,
from include/linux/atomic.h:4,
from include/linux/spinlock.h:402,
from include/linux/seqlock.h:35,
from include/linux/time.h:5,
from include/uapi/linux/timex.h:56,
from include/linux/timex.h:56,
from include/linux/sched.h:19,
from include/linux/pid_namespace.h:4,
from kernel/debug/debug_core.c:30:
kernel/debug/debug_core.c: In function ‘kgdb_cpu_enter’:
linux/arch/arm64/include/asm/cmpxchg.h:75:3: warning: value computed is not used [-Wunused-value]
((__typeof__(*(ptr)))__xchg((unsigned long)(x),(ptr),sizeof(*(ptr))))
^
linux/arch/arm64/include/asm/atomic.h:132:30: note: in expansion of macro ‘xchg’
#define atomic_xchg(v, new) (xchg(&((v)->counter), new))
kernel/debug/debug_core.c:504:4: note: in expansion of macro ‘atomic_xchg’
atomic_xchg(&kgdb_active, cpu);
^
This patch makes use of the same trick as we do for cmpxchg, by assigning
the return value to a dummy variable in the xchg() macro itself.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit e1dfda9ced)
Signed-off-by: Mark Brown <broonie@linaro.org>
arm64 sets CONFIG_64BIT=y and hence uses the "long counter" atomic64_t
definition from include/linux/types.h. Make atomic64_read() return "long",
not "long long".
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit ba6bf8c85c)
Signed-off-by: Mark Brown <broonie@linaro.org>
The ARMv8 architecture allows execute-only user permissions by clearing
the PTE_UXN and PTE_USER bits. The kernel, however, can still access
such page, so execute-only page permission does not protect against
read(2)/write(2) etc. accesses. Systems requiring such protection must
implement/enable features like SECCOMP.
This patch changes the arm64 __P100 and __S100 protection_map[] macros
to the new __PAGE_EXECONLY attributes. A side effect is that
pte_valid_user() no longer triggers for __PAGE_EXECONLY since PTE_USER
isn't set. To work around this, the check is done on the PTE_NG bit via
the pte_valid_ng() macro. VM_READ is also checked now for page faults.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit bc07c2c6e9)
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch removes the aux_context structure (and the containing file)
to allow the placement of the _aarch64_ctx end magic based on the
context stored on the signal stack.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 0e0276d1e1)
Signed-off-by: Mark Brown <broonie@linaro.org>
The synchronisation with the boot thread already happens in __cpu_up()
via wait_for_completion_timeout(). In addition, __cpu_up() calls are
protected by the cpu_add_remove_lock mutex and already serialised.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 6400111399)
Signed-off-by: Mark Brown <broonie@linaro.org>
Clock providers should be initialized before clocksource_of_init.
If not, Clock source initialization can be fail to get the clock.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit bc3ee18a7a)
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to support earlycon on arm64, we need to enable earlycon fixmap
support.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 92cc15fcb5)
Signed-off-by: Mark Brown <broonie@linaro.org>
Conflicts:
arch/arm64/Kconfig
Recently, the default DMA ops have been changed to non-coherent for
alignment with 32-bit ARM platforms (and DT files). This patch adds bus
notifiers to be able to set the coherent DMA ops (with no cache
maintenance) for devices explicitly marked as coherent via the
"dma-coherent" DT property.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 6ecba8eb51)
Signed-off-by: Mark Brown <broonie@linaro.org>
Presently, paging_init() calls init_mem_pgprot() to initialize pgprot
values used by macros such as PAGE_KERNEL, PAGE_KERNEL_EXEC, etc.
The new fixmap and early_ioremap support also needs to use these macros
before paging_init() is called. This patch moves the init_mem_pgprot()
call out of paging_init() and into setup_arch() so that pgprot_default
gets initialized in time for fixmap and early_ioremap.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(cherry picked from commit 0bf757c73d)
Signed-off-by: Mark Brown <broonie@linaro.org>
The Kconfig for CONFIG_STRICT_DEVMEM is missing despite being
used in mmap.c. Add it.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit d253b4406d)
Signed-off-by: Mark Brown <broonie@linaro.org>
Conflicts:
arch/arm64/Kconfig.debug
This reverts commit 82b2f495fb. The
__boot_cpu_mode variable is flushed in head.S after being written,
therefore the additional cache flushing is no longer required.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 0a997ecc08)
Signed-off-by: Mark Brown <broonie@linaro.org>
DMA_ATTR_WRITE_COMBINE is currently ignored. Set the pgprot
appropriately for non coherent opperations.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 214fdbe74a)
Signed-off-by: Mark Brown <broonie@linaro.org>
The current dma_ops do not specify an mmap function so maping
falls back to the default implementation. There are at least
two issues with using the default implementation:
1) The pgprot is always pgprot_noncached (strongly ordered)
memory even with coherent operations
2) dma_common_mmap calls virt_to_page on the remapped non-coherent
address which leads to invalid memory being mapped.
Fix both these issue by implementing a custom mmap function which
correctly accounts for remapped addresses and sets vm_pg_prot
appropriately.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
[catalin.marinas@arm.com: replaced "arm64_" with "__" prefix for consistency]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 6e8d7968e9)
Signed-off-by: Mark Brown <broonie@linaro.org>
Without this, the following scenario is incorrectly determined
to be invalid.
addr 0x7f_ffffe000 size 8192 addr_limit 0x80_00000000
This behavior was observed while trying to vmsplice the stack
as part of a CRIU dump of a process on a system started with the
norandmaps kernel parameter.
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 31b1e940c5)
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the DTS entries for the APM X-Gene SoC 15Gbps Multi-purpose
PHY driver. The PHY for SATA controller 2 and 3 are enabled by default.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Tuan Phan <tphan@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
(cherry picked from commit 71b70ee935)
Signed-off-by: Mark Brown <broonie@linaro.org>
asm-generic offers an atomic-add based rwsem implementation, which
can avoid the need for heavier, spinlock-based synchronisation on the
fast path.
This patch makes use of the optimised implementation for arm64 CPUs.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit c209f79940)
Signed-off-by: Mark Brown <broonie@linaro.org>
asm-generic/rwsem.h used to live under arch/powerpc. During its
liberation to common code, a few references to its former home where
preserved, in particular the definition of RWSEM_ACTIVE_MASK is
predicated on CONFIG_PPC64.
This patch updates the ifdefs and comments to architecturally neutral
versions.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit e172800e5d)
Signed-off-by: Mark Brown <broonie@linaro.org>
Make smp_spin_table_cpu_postboot() static, because this function
is used only in this file.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 7184659bed)
Signed-off-by: Mark Brown <broonie@linaro.org>
Make local symbols static, because these are used only in this
file.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 242c04bc4b)
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 8adbf57fc4 ("irqchip: gic: use dmb ishst instead of dsb when
raising a softirq") added an explicit dmb(...) call to the GIC driver.
This patch adds a simple dmb() macro to arm64, which expands to a DMB SY
instruction.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit d152d22a18)
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently we flush the entire dcache at boot within __cpu_setup, but
this is unnecessary as the booting protocol demands that the dcache is
invalid and off upon entering the kernel. The presence of the cache
flush only serves to hide bugs in bootloaders, and is not safe in the
presence of SMP.
In an SMP boot scenario the CPUs enter coherency outside of the kernel,
and the primary CPU enables its caches before bringing up secondary
CPUs. Therefore if any secondary CPU has an entry in its cache (in
violation of the boot protocol), the primary CPU might snoop it even if
the secondary CPU's cache is disabled. The boot-time cache flush only
serves to hide a firmware bug, and slows down a cpu boot unnecessarily.
This patch removes the unnecessary boot-time cache flush.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
[catalin.marinas@arm.com: make __flush_dcache_all local only]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit bff705950e)
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit fb4a96029c (arm64: kernel: fix per-cpu offset restore on
resume) uses per_cpu_offset() unconditionally during CPU wakeup,
however, this is only defined for the SMP case.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Dave P Martin <Dave.Martin@arm.com>
(cherry picked from commit b57fc9e806)
Signed-off-by: Mark Brown <broonie@linaro.org>
psci_init() is written to return err code if something goes wrong. However,
the single user, setup_arch(), doesn't care about it. Moreover, every error
path is supplied with a clear message which is enough for pleasant debugging.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 64b4f60f49)
Signed-off-by: Mark Brown <broonie@linaro.org>
Since 652af89979 "arm64: factor out spin-table
boot method" psci prefix's been introduced. We have a common pr_fmt, so clean
them up.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 288ac26cc2)
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove some unnecessary bits that were apparently carried over from
another architecture's implementation:
- No need to get_page() the vdso text/data - these are part of the
kernel image.
- No need for ClearPageReserved on the vdso text.
- No need to vmap the first text page to check the ELF header - this
can be done through &vdso_start.
Also some minor cleanup:
- Use kcalloc for vdso_pagelist array allocation.
- Don't print on allocation failure, slab/slub will do that for us.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 16fb1a9bec)
Signed-off-by: Mark Brown <broonie@linaro.org>
arm64_swiotlb_alloc/free_coherent name can be misleading
somtimes with CMA support being enabled after this
patch (c2104debc235b745265b64d610237a6833fd53)
Change this name to be more generic:
__dma_alloc/free_coherent
Signed-off-by: Ritesh Harjani <ritesh.harjani@gmail.com>
[catalin.marinas@arm.com: renamed arm64_swiotlb_dma_ops to coherent_swiotlb_dma_ops]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit bb10eb7b4d)
Signed-off-by: Mark Brown <broonie@linaro.org>
Change the soft_restart() routine to call cpu_reset() at its identity mapped
physical address.
The cpu_reset() routine must be called at its identity mapped physical address
so that when the MMU is turned off the instruction pointer will be at the correct
location in physical memory.
Signed-off-by: Geoff Levand <geoff@infradead.org> for Huawei, Linaro
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 09024aa61e)
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch changes the idmap page table creation during boot to cover
the whole kernel image, allowing functions like cpu_reset() to be safely
called with the physical address.
This patch also simplifies the create_block_map asm macro to no longer
take an idmap argument and always use the phys/virt/end parameters. For
the idmap case, phys == virt.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit ea8c2e1124)
Signed-off-by: Mark Brown <broonie@linaro.org>
processor debug state PSTATE.D is unmasked in smp call
clear_os_lock for secondary cpus. So debug state is still
masked in normal kernel context. With this patch, unmask
debug state on secondary boot for the cpus in normal kernel
context. Now kgdb tests passed with multicore.
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@caviumnetworks.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit d8ed442a00)
Signed-off-by: Mark Brown <broonie@linaro.org>
Conflicts:
arch/arm64/kernel/smp.c
The patch moves the PCI I/O space (currently at 64K) before the
earlyprintk mapping and extends it to 16MB.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 22bd1c91fe)
Signed-off-by: Mark Brown <broonie@linaro.org>
Conflicts:
Documentation/arm64/memory.txt
As commit a9468f30b5 "ARM: 7333/2: jump label: detect %c
support for ARM", this patch detects the same thing for ARM64
because some ARM64 GCC versions have the same issue.
Some versions of ARM64 GCC which do support asm goto, do not
support the %c specifier. Since we need the %c to support jump
labels on ARM64, detect that too in the asm goto detection script
to avoid build errors with these versions.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit f3c003f72d)
Signed-off-by: Mark Brown <broonie@linaro.org>
Add HAVE_ARCH_KGDB for arm64 Kconfig
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@caviumnetworks.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 9529247db9)
Signed-off-by: Mark Brown <broonie@linaro.org>
Conflicts:
arch/arm64/Kconfig
typecast instruction_pointer macro to unsigned long to
resolve following compiler warnings like
warning: format '%lx' expects argument of type 'long unsigned int',
but argument 2 has type 'u64' [-Wformat]
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@caviumnetworks.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 58dcc204f1)
Signed-off-by: Mark Brown <broonie@linaro.org>
Add KGDB software step debugging support for EL1 debug
in AArch64 mode.
KGDB registers step debug handler with debug monitor.
On receiving 'step' command from GDB tool, target enables
software step debugging and step address is updated in ELR.
Software Step debugging is disabled when 'continue' command
is received
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@caviumnetworks.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 44679a4f14)
Signed-off-by: Mark Brown <broonie@linaro.org>
Add KGDB debug support for kernel debugging.
With this patch, basic KGDB debugging is possible.GDB register
layout is updated and GDB tool can establish connection with
target and can set/clear breakpoints.
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@caviumnetworks.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit bcf5763b0d)
Signed-off-by: Mark Brown <broonie@linaro.org>
Conflicts:
arch/arm64/kernel/Makefile
Add macros to enable and disable to manage PSTATE.D
for debugging. The macros local_dbg_save and local_dbg_restore
are moved to irqflags.h file
KGDB boot tests fail because of PSTATE.D is masked.
unmask it for debugging support
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@caviumnetworks.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit c7db4ff5d2)
Signed-off-by: Mark Brown <broonie@linaro.org>
