The flag isn't used, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If no parameter needs to be modified, make preview_config() and
preview_setup_hw() return immediately. This speeds up interrupt handling
in the common case.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Brightness and contrast are handled through V4L2 controls. Their
configuration bit in the preview engine update attributes table is set
to -1 to reflect that. However, the VIDIOC_OMAP3ISP_PRV_CFG ioctl
handler doesn't handle -1 correctly as a configuration bit value, and
erroneously considers that the parameter has been selected for update by
the ioctl caller. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When propagating the frame number through the pipeline, the frame number
must be incremented at frame start by the appropriate IRQ handler. This
was properly handled for the CSI2 and CCP2 receivers, but not when the
CCDC parallel interface is used.
ADD frame number incrementation to the HS/VS interrupt handler. As the
HS/VS interrupt is also generated for frames received by the CSI2 and
CCP2 receivers, remove explicit propagation handling from the serial
receivers.
Reported-by: Kruno Mrak <kruno.mrak@matrix-vision.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Tested-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
iommu_domain_free() was called in isp_remove() before omap3isp_put().
omap3isp_put() must not save the context if the IOMMU no longer is there.
Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The OMAP3 ISP preview engine will violate the L4 bus protocol if we try
to write some of its internal registers after it failed to stop
properly. This generates an external abort on non-linefetch fault,
triggering a fatal kernel oops.
We can't always prevent preview engine stop failures (they can for
instance be caused by a sensor crash), but we can improve the system
reliability by refusing to start streaming on a pipeline that contains
the preview engine if it failed to stop. The driver will then eventually
reset the ISP (when all applications will have closed their file handles
related to OMAP3 ISP device nodes), making the ISP usable again.
Fixes: NB#291334 - camera: Recover gracefully from ISP crash instead of oopsing
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Reviewed-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The get_unmapped_area() operation was forgotten during conversion to
videobuf2. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Properly validate the user-supplied index against the number of inputs.
The code used the pin local variable instead of the index by mistake.
Reported-by: Jozef Vesely <vesely@gjh.sk>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In case of short marker, the number of received packets was not
incremented doing a zero divide when computing the filling rate.
Reported-by: Hans Petter Selasky <hans.petter.selasky@bitfrost.no>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the embed percpu first chunk allocator, x86 uses either PAGE_SIZE
or PMD_SIZE for atom_size. PMD_SIZE is used when CPU supports PSE so
that percpu areas are aligned to PMD mappings and possibly allow using
PMD mappings in vmalloc areas in the future. Using larger atom_size
doesn't waste actual memory; however, it does require larger vmalloc
space allocation later on for !first chunks.
With reasonably sized vmalloc area, PMD_SIZE shouldn't be a problem
but x86_32 at this point is anything but reasonable in terms of
address space and using larger atom_size reportedly leads to frequent
percpu allocation failures on certain setups.
As there is no reason to not use PMD_SIZE on x86_64 as vmalloc space
is aplenty and most x86_64 configurations support PSE, fix the issue
by always using PMD_SIZE on x86_64 and PAGE_SIZE on x86_32.
v2: drop cpu_has_pse test and make x86_64 always use PMD_SIZE and
x86_32 PAGE_SIZE as suggested by hpa.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Yanmin Zhang <yanmin.zhang@intel.com>
Reported-by: ShuoX Liu <shuox.liu@intel.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <4F97BA98.6010001@intel.com>
Cc: stable@vger.kernel.org
The H_REGISTER_VPA hcall implementation in HV Power KVM needs to pin some
guest memory pages into host memory so that they can be safely accessed
from usermode. It does this used get_user_pages_fast(). When the VPA is
unregistered, or the VCPUs are cleaned up, these pages are released using
put_page().
However, the get_user_pages() is invoked on the specific memory are of the
VPA which could lie within hugepages. In case the pinned page is huge,
we explicitly find the head page of the compound page before calling
put_page() on it.
At least with the latest kernel, this is not correct. put_page() already
handles finding the correct head page of a compound, and also deals with
various counts on the individual tail page which are important for
transparent huge pages. We don't support transparent hugepages on Power,
but even so, bypassing this count maintenance can lead (when the VM ends)
to a hugepage being released back to the pool with a non-zero mapcount on
one of the tail pages. This can then lead to a bad_page() when the page
is released from the hugepage pool.
This removes the explicit compound_head() call to correct this bug.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This reverts commit 785f857d1c.
The commit causes a problem with the wrong D3 state after suspend
because the call of hda_set_power_state() involves with the power-up
sequence, which changes the power_count, and this confuses the resume
sequence that checks the power_count as well.
Originally, this go-to-D3 sequence should be a simple task without the
power-up sequence. But, it'd need some proper sanity checks in the
case of power-saved state, so it's not too easy to write now in the
3.4-rc cycle.
In short, the safest option now is to revert this affecting commit.
Of course, we need to clean up and robustify the power-saving code
better for 3.5 kernel.
Reported-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Include the header to pickup the definitions of the exported symbols.
Quiets the following sparse warnings:
warning: symbol 'vb2_dma_contig_memops' was not declared. Should it be static?
warning: symbol 'vb2_dma_contig_init_ctx' was not declared. Should it be static?
warning: symbol 'vb2_dma_contig_cleanup_ctx' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function vb2_dma_contig_vaddr returns a void * not an integer.
Quiets the sparse noise:
warning: Using plain integer as NULL pointer
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The vb2_get_vma() function is called by videobuf2-dma-contig. Export it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The commit 3b4c34aac7
"s5p-fimc: Add support for VIDIOC_PREPARE_BUF/CREATE_BUFS ioctls"
added a handler for VIDIOC_CREATE_BUFS ioctl, but the queue_setup
callback wasn't updated to properly interpret the pixel format.
In this situation memory corruption may happen with VIDIOC_CREATE_BUFS
ioctl. Update the queue_setup op to fix this.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The call for alc_auto_parse_customize_define() must be done after the
fixup pre-probe initialization. Otherwise SKU_IGNORE fixup won't work
properly (e.g. HP RP5800 with ALC662 codec).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When setting TRY crop on the sub-device the mutex was erroneously acquired
rather than released on exit path. This bug is present in kernels starting
from v3.2.
Cc: stable@vger.kernel.org
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changeset 5bfaadde broke zig-zag for DVB-S drivers that don't
implement get_tune_settings() callback.
Fix the code, in order to allow it to work as before, otherwise
some channels may not be tuned anymore.
Fix Fedora Bugzilla:
https://bugzilla.redhat.com/show_bug.cgi?id=814404
Cc: stable@kernel.org # for Kernel v3.3
Reported-by: Michael Heijenga <database.worker@googlemail.com>
Tested-by: Michael Heijenga <database.worker@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
snd_hdsp uses its own ioctls to acquire config- and status information.
Expose the corresponding ioctl handler via ioctl_compat, so that 32bit applications can use it on 64bit kernels.
Signed-off-by: Andre Schramm <andre.schramm@iosono-sound.com>
Reviewed-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable Coldfire QSPI support when SPI_COLDFIRE_QSPI is built as a module.
This version of the patch combines changes to the config files and device.c
and uses IF_ENABLED (thanks to Sam Ravnborg for the suggestion).
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
When the kernel validates set TCP/UDP port actions, it looks at
the ports in the existing flow to make sure that the L4 header exists.
However, these actions always use the IPv4 version of the struct.
Following patch fixes this by checking for flow ip protocol first.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Neither compare_ether_addr() nor compare_ether_addr_64bits()
(as it can fall back to the former) have comparison semantics
like memcmp() where the sign of the return value indicates sort
order. We had a bug in the wireless code due to a blind memcmp
replacement because of this.
A cursory look suggests that the wireless bug was the only one
due to this semantic difference.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The V4L querystd implementation appears to want to narrow down the
list of available standards by starting with a hardware-supported list
and then attempting to detect which among those are actually
available. Prior to this change in the pvrusb2 driver we started with
all possible standards. With this change in place we instead narrow
to just the standards that we know the hardware can actually support.
For example, this removes the ATSC standards from the list if we
aren't dealing with a hybrid device...
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Get rid of pvrusb2-local implementation for enumeration of video
standards - with video_ioctl2 this happens automatically now in the
v4l core.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the transition to ioctl2, the pvrusb2 driver's own standards
enumeration is no longer used. Instead a generic algorithm internal
to v4l is used (which is a great idea - since the pvrusb2
implementation itself was generic anyway). This change ensures that
the v4l algorithm works with the correct set of hardware supported
standards. This resolves a FIXME left behind from the videodev_ioctl2
transition.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Other aspects of the pvrusb2 driver - including in particular those
dealing with video standards - all use internal control IDs for
uniform access by the interfaces. By exporting the querystd result as
another control ID, uniform access to it becomes available through the
sysfs interface.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move full implementation of pvr2_hdw_get_detected_std() actually
include pvr2_hdw_get_detected_std().
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note: there is one FIXME remaining: the tvnorms field of struct
video_device should be set up correctly. I have used V4L2_STD_ALL for
now, but I'm sure this can be improved. This field is used by
video_ioctl2 to implement ENUMSTD.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In any statically initialized data structure, the compiler is going to
zero any part which is not already explicitly initialized. While we
can take that knowledge overboard and simply avoid initializing
anything that needs to be zero, it's at least a good idea not to
bother zeroing parts that we don't otherwise care about - like
"reserved" fields which may change in the future. Avoiding
initialization of those fields now also avoids possible conflict down
the road.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This allows v4l2 control UI-s to update the inactive state (ie grey-ing
out of controls) for slave controls when the master control changes.
[Use __uvc_find_control() to find slave controls, as they're always
located in the same entity as the corresponding master control]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note the unused in this patch slave_ids addition to the mappings will get
used in a follow up patch to generate control change events for the slave
ctrls when their flags change due to the master control changing value.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This avoids the need for doing a forward declaration of __uvc_ctrl_get
(which is a static function) in later patches in this series.
Note to reviewers this patch does not change a single line of code, it
just moves the function up in uvc_ctrl.c a bit.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a preparation patch for adding ctrl event support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The locking policy is such that the erase_complete_block spinlock is
nested within the alloc_sem mutex. This fixes a case in which the
acquisition order was erroneously reversed. This issue was caught by
the following lockdep splat:
=======================================================
[ INFO: possible circular locking dependency detected ]
3.0.5 #1
-------------------------------------------------------
jffs2_gcd_mtd6/299 is trying to acquire lock:
(&c->alloc_sem){+.+.+.}, at: [<c01f7714>] jffs2_garbage_collect_pass+0x314/0x890
but task is already holding lock:
(&(&c->erase_completion_lock)->rlock){+.+...}, at: [<c01f7708>] jffs2_garbage_collect_pass+0x308/0x890
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&(&c->erase_completion_lock)->rlock){+.+...}:
[<c008bec4>] validate_chain+0xe6c/0x10bc
[<c008c660>] __lock_acquire+0x54c/0xba4
[<c008d240>] lock_acquire+0xa4/0x114
[<c046780c>] _raw_spin_lock+0x3c/0x4c
[<c01f744c>] jffs2_garbage_collect_pass+0x4c/0x890
[<c01f937c>] jffs2_garbage_collect_thread+0x1b4/0x1cc
[<c0071a68>] kthread+0x98/0xa0
[<c000f264>] kernel_thread_exit+0x0/0x8
-> #0 (&c->alloc_sem){+.+.+.}:
[<c008ad2c>] print_circular_bug+0x70/0x2c4
[<c008c08c>] validate_chain+0x1034/0x10bc
[<c008c660>] __lock_acquire+0x54c/0xba4
[<c008d240>] lock_acquire+0xa4/0x114
[<c0466628>] mutex_lock_nested+0x74/0x33c
[<c01f7714>] jffs2_garbage_collect_pass+0x314/0x890
[<c01f937c>] jffs2_garbage_collect_thread+0x1b4/0x1cc
[<c0071a68>] kthread+0x98/0xa0
[<c000f264>] kernel_thread_exit+0x0/0x8
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&(&c->erase_completion_lock)->rlock);
lock(&c->alloc_sem);
lock(&(&c->erase_completion_lock)->rlock);
lock(&c->alloc_sem);
*** DEADLOCK ***
1 lock held by jffs2_gcd_mtd6/299:
#0: (&(&c->erase_completion_lock)->rlock){+.+...}, at: [<c01f7708>] jffs2_garbage_collect_pass+0x308/0x890
stack backtrace:
[<c00155dc>] (unwind_backtrace+0x0/0x100) from [<c0463dc0>] (dump_stack+0x20/0x24)
[<c0463dc0>] (dump_stack+0x20/0x24) from [<c008ae84>] (print_circular_bug+0x1c8/0x2c4)
[<c008ae84>] (print_circular_bug+0x1c8/0x2c4) from [<c008c08c>] (validate_chain+0x1034/0x10bc)
[<c008c08c>] (validate_chain+0x1034/0x10bc) from [<c008c660>] (__lock_acquire+0x54c/0xba4)
[<c008c660>] (__lock_acquire+0x54c/0xba4) from [<c008d240>] (lock_acquire+0xa4/0x114)
[<c008d240>] (lock_acquire+0xa4/0x114) from [<c0466628>] (mutex_lock_nested+0x74/0x33c)
[<c0466628>] (mutex_lock_nested+0x74/0x33c) from [<c01f7714>] (jffs2_garbage_collect_pass+0x314/0x890)
[<c01f7714>] (jffs2_garbage_collect_pass+0x314/0x890) from [<c01f937c>] (jffs2_garbage_collect_thread+0x1b4/0x1cc)
[<c01f937c>] (jffs2_garbage_collect_thread+0x1b4/0x1cc) from [<c0071a68>] (kthread+0x98/0xa0)
[<c0071a68>] (kthread+0x98/0xa0) from [<c000f264>] (kernel_thread_exit+0x0/0x8)
This was introduce in '81cfc9f jffs2: Fix serious write stall due to erase'.
Cc: stable@kernel.org [2.6.37+]
Signed-off-by: Josh Cartwright <joshc@linux.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
I'm seeing an oops in mtd_dataflash.c with Linux 3.3. What appears to
be happening is that otp_select_filemode calls mtd_read_fact_prot_reg
with -1 for offset and length and a NULL buffer to test if OTP
operations are supported. This finds its way down to otp_read in
mtd_dataflash.c and causes an oops when memcpying the returned data
into the NULL buf.
None of the checks in otp_read catches the negative length and offset.
Changing the length of the dummy read to 0 prevents the oops.
Cc: stable@kernel.org [3.3+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Just like with ctrl events, drivers may want to get called back on
listener add / remove for other event types too. Rather then special
casing all of this in subscribe / unsubscribe event it is better to
use ops for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver was severely broken. This patch makes it work again, and updates
it to the latest V4L2 frameworks (except for videobuf2). It passes the
v4l2-compliance tests and it now handles suspend/resume correctly.
Several custom controls are replaced by new standard controls, only the
USB_ALTERNATE control remains.
Tested with the Hanse HVS-CM500PC USB microscope.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The et61x251 has been deprecated for a couple of releases now, as all
devices it supports are also supported by gspca_etoms, and it has not
seen any maintenance in years. So now it is time to remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
