Samsung S3C2416 has two SDHCI controllers compatible with other
Samsung's SoCs (S3C64XX, S5PC100 etc...).
Add required platform setup code that the devices can be used with
sdhci-s3c driver.
Signed-off-by: Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
[kgene.kim@samsung.com: change to __raw_{readl,writel} from {readl,writel}]
[kgene.kim@samsung.com: build error fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Define maps for HSMMC devices.
S3C2443 has one HSMMC device with base address 0x4A800000.
S3C2416 has HSMMC0 at 0x4AC00000 and HSMMC1 at 0x4A800000.
So suppose that S3C2443 has only HSMMC1.
Define clock for hsmmc0 device and register it.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
fsib_clk will be used when fdiv_clk failed on fsi_hdmi_set_rate.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a sched_clock() implementation to Versatile Express using the new
sched_clock() infrastructure for extending 32bit counters to full
64-bit nanoseconds.
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Prepare the ap4evb board for the MIPI DSI driver transition to support
different register layouts.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now, that the MIPI DSI driver implements runtime PM, we don't need anymore to
configure clocks statically in the platform code. This patch also adds a DSITX1
clock definition for sh7372 and attaches PHY clocks to respective devices.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh73a0 has divisor[12] setting as 1/7 on FRQCRA.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add VGA camera support to the Mackerel board
using soc_camera_platform.
The VGA camera module is hooked up using the
8-bit CEU bus, and it is constantly bursting
out frames in fixed video mode setting. The
camera module does not allow any I2C control.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The maximum transfer size of the stedma40 is (64k-1) x data-width.
If the transfer size of one element exceeds this limit
the job is split up and sent as linked transfer.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
1. pll_base address should return right value
2. uart parent clk is from pll3
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch changes the clock registration code to use the s3c_register_clocks()
followed by s3c_disable_clocks() instead of the loops it was using and cleanups
the return of s3c24xx_register_clocks() because it includes it.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the clock registration code to use the s3c_register_clocks()
followed by s3c_disable_clocks() instead of the loops it was using and cleanups
the return of s3c24xx_register_clocks() because it includes it.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the clock registration code to use the s3c_register_clocks()
followed by s3c_disable_clocks() instead of the loops it was using.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the clock registration code to use the s3c_register_clocks()
followed by s3c_disable_clocks() instead of the loops it was using.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the clock registration code to use the s3c_register_clocks()
followed by s3c_disable_clocks() instead of the loops it was using.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the clock registration code to use the s3c_register_clocks()
followed by s3c_disable_clocks() instead of the loops it was using.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the clock registration code to use the s3c_register_clocks()
followed by s3c_disable_clocks() instead of the loops it was using.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Replace some magic numbers with constants and add interrupt definitions.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit 7a5b4e16c8, simpad devices don't
boot anymore, since platform devices are registered too early. Fix by moving
the registration from map_io to arch_initcall as done on other sa1100 boards.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Before this patch, the following error would sometimes occur after a
resume on pxa3xx:
/path/to/mm/memory.c:144: bad pmd 8040542e.
The problem was that a temporary page table mapping was being improperly
restored.
The PXA3xx resume code creates a temporary mapping of resume_turn_on_mmu
to avoid a prefetch abort. The pxa3xx_resume_after_mmu code requires
that the r1 register holding the address of this mapping not be
modified, however, resume_turn_on_mmu does modify it. It is mostly
correct in that r1 receives the base table address, but it may also
get other bits in 13:0. This results in pxa3xx_resume_after_mmu
restoring the original mapping to the wrong place, corrupting memory
and leaving the temporary mapping in place.
Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The commit 6ac6b817f3 (ARM: pxa: encode
IRQ number into .nr_irqs) removed definition of ITE_LAST_IRQ which
caused the following build error:
CC arch/arm/common/it8152.o
arch/arm/common/it8152.c: In function 'it8152_init_irq':
arch/arm/common/it8152.c:86: error: 'IT8152_LAST_IRQ' undeclared (first use in this function)
arch/arm/common/it8152.c:86: error: (Each undeclared identifier is reported only once
arch/arm/common/it8152.c:86: error: for each function it appears in.)
make[2]: *** [arch/arm/common/it8152.o] Error 1
Defining the IT8152_LAST_IRQ in the arch/arm/include/hardware/it8152.c
fixes the build.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
MX27_3DS board has a MC13783 PMIC connected to the CSPI2 port.
Add support for the PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Replace the page_to_dma() and dma_to_page() macros with their PFN
equivalents. This allows us to map parts of memory which do not have
a struct page allocated to them to bus addresses. This will be used
internally by dma_alloc_coherent()/dma_alloc_writecombine().
Build tested on Versatile, OMAP1, IOP13xx and KS8695.
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The stop function sets the DMA_HALT bit, which prevents
the DMA transfer to resume after stop, for example during
audio PAUSE/PLAY cycle. Clear the HALT bit during start.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
When GENERIC_HARDIRQS_NO_DEPRECATED is enabled, a number of struct
irq_desc members stop being directly accessible, and need to be
accessed via the irq_data struct instead -- this patch fixes up the
plat-samsung sites that still access those members directly.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
