Remove the depencency on the IOMMU IDR register, as it may
not be accessible depending on the security configuraton.
This involves moving the NCB field of IDR into the platform
data.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Use ASID tags in the TLB instead of VMID tags in
preparation for changes to the secure environment.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Clean up the clock control code in the probe calls, and add
support for controlling the clock for the IOMMU bus
interconnect. With the (proper) clock driver in place, the
clock control logic in the probe function can be made much
cleaner since it does not have to deal with the placeholder
driver anymore.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Reviewed-by: Trilok Soni <tsoni@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Add clock control to the IOMMU driver. The IOMMU bus clock
(and potentially an AXI clock) need to be on to gain access
to IOMMU registers. Actively control these clocks when
needed instead of leaving them on.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
This typo was fixed in 46e3f30 (mx25: fix spi device registration typo), but a
the merge at 0e44e059 (Merge commit 'v2.6.37-rc4' into imx-for-2.6.38) resolved
the merge conflict wrongly.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
TrimSlice has MicroSD and standard MMC/SD slots.
Register sdhci devices and enable GPIOs for MMC/SD slot.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C64XX: Update regulator names for debugfs compatiblity on SMDK6410
ARM: S3C64XX: Fix build with WM1190 disabled and WM1192 enabled on SMDK6410
ARM: S3C64XX: Reduce output of s3c64xx_dma_init1()
ARM: S3C64XX: Tone down SDHCI debugging
ARM: S3C64XX: Add clock for i2c1
ARM: S3C64XX: Staticise non-exported GPIO to interrupt functions
ARM: SAMSUNG: Include devs.h in dev-uart.c to prototype devices
ARM: S3C64XX: Fix keypad setup to configure correct number of rows
ARM: S3C2440: Fix usage gpio bank j pin definitions on GTA02
ARM: S5P64X0: Fix number of GPIO lines in Bank F
ARM: S3C2440: Select missing S3C_DEV_USB_HOST on GTA02
Add a clockdomain to the GPTIMER7 interface and 2430 HSMMC2 functional
clocks - both were previously missing them.
Also, the 2430 mmchs1_fck is in core_l3_clkdm, but should be in
core_l4_clkdm; fix this.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch fixes these warnings when building kernel for OMAP3EVM
only.
CC arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.o
arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c:95: warning:
'dsp_24xx_wkdeps' defined but not used
arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c:119: warning:
'mpu_24xx_wkdeps' defined but not used
arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c:147: warning:
'core_24xx_wkdeps' defined but not used
The problem should be noticed when building for other OMAP3
platforms (only) as well.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
After commit 81b34fbecb ("OMAP2 clock:
split OMAP2420, OMAP2430 clock data into their own files"), it's
possible to remove dsp_irate_ick from the OMAP2420 and OMAP2430 clock
files. It was originally only needed due to a 2420/2430 clock tree difference,
and now that the data is in separate files, it's superfluous.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove the DPLL rate tolerance code that is called during rate
rounding. As far as I know, this code is never used, since it's been
more important for callers of the DPLL round_rate()/set_rate()
functions to obtain an exact rate than it is to save a relatively
small amount of power.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Bail out before we take the clockfw_lock spinlock if the corresponding
OMAP1 or OMAP2+ clock function is not defined. The intention is to
reduce and simplify the work that is done inside the spinlock.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The parent of the interface clocks for GPTIMER1, MPU_WDT,
SYNCTIMER_32K, SCM, WDT1, and the ICR (2430 only) were all listed as
being l4_ck. This isn't accurate; these modules exist inside the WKUP
domain, and the interface clock to these modules runs at the SYS_CLK
rate rather than the CORE L4 rate.
So, create a new clock "wu_l4_ick", similar to the OMAP3
"wkup_l4_ick", that serves as the parent for these clocks.
Also, these clocks were listed as existing inside core_l4_clkdm;
wkup_clkdm is probably more accurate.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP2420/2430 external 32-kHz low-frequency oscillator is a 32768
Hz oscillator, not a 32,000 Hz oscillator[1][2]. Fix this in the clock
tree.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
1. OMAP2420/22 Multimedia Processor Data Manual, Version P [SWPS019P],
section 5.1.4 "External 32-kHz CMOS Clock" (note that it refers to
a "32.768-kHz" clock; this presumably should be "32.768-KHz")
2. OMAP2430 Multimedia Processor ES2.1 Data Manual, Version V [SWPS023V],
section 5.1.4 "External 32-kHz CMOS Clock" (note that it refers to
a "32.768-kHz" clock; this presumably should be "32.768-KHz")
Several clocks are listed as having the core L4 clock as their parent,
when they are actually derived from the L3 clock. Fix these.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
At this point in time, there's no reason for this header file to be in
plat-omap/include/plat/voltage.h. It should not be included by device
drivers, and the code that uses it is currently all under mach-omap2/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
There's no reason for this header file to be in
plat-omap/include/plat/smartreflex.h. The hardware devices are in
OMAP2+ SoCs only. Leaving this header file in plat-omap causes
problems due to cross-dependencies with other header files that should
live in mach-omap2/.
Thanks to Benoît Cousson <b-cousson@ti.com> for suggesting the removal
of the smartreflex.h include from the OMAP3xxx hwmod data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
These CM_AUTOIDLE bits are now set by the clock code via the common PM
code in mach-omap2/pm.c.
N.B.: The pm24xx.c code that this patch removes didn't ensure that the
CM_AUTOIDLE bits were set for several 2430-only modules, such as
GPIO5, MDM_INTC, MMCHS1/2, the modem oscillator clock, and USBHS.
Similarly, the pm34xx.c code that this patch removes didn't ensure
that the CM_AUTOIDLE bits were set for USIM and the AM3517 UART4.
Those cases should now be handled.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Mark each interface clock with a corresponding CM_AUTOIDLE bit with
a clkops that has the allow_idle/deny_idle function pointers populated.
This allows the OMAP clock framework to enable and disable autoidle for
these clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Mark each interface clock with a corresponding CM_AUTOIDLE bit with
a clkops that has the allow_idle/deny_idle function pointers populated.
This allows the OMAP clock framework to enable and disable autoidle for
these clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
OMAP2430 and OMAP3xxx have modem autoidle bits that are actually
attached to clocks with CM_FCLKEN bits; add the code and data to
handle these.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Mark each interface clock with a corresponding CM_AUTOIDLE bit with
a clkops that has the allow_idle/deny_idle function pointers populated.
This allows the OMAP clock framework to enable and disable autoidle for
these clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Add sdrc_ick to the OMAP2420 clock data so the clock code can control
the CM_AUTOIDLE bit associated with this clock.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Add interface clock type code with autoidle enable/disable support.
The clkops structures created in this file will be used for all
OMAP2/3 interface clocks with autoidle support. They will enable the
clock framework to control interface clock autoidle directly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Place some comments in the OMAP oscillator clock control code to note that
its autoidle mode should eventually be controlled via the new OMAP clockfw
autoidle control interface.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
OMAP2xxx devices have two on-chip APLLs. These APLLs can
automatically enter idle when not in use. Connect the APLL autoidle
code to the clock code, so that the clock framework can handle this
process. As part of this patch, remove the code in mach-omap2/pm24xx.c
that previously handled APLL autoidle control.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Add the necessary code and data to allow the clock framework to enable
and disable the OMAP2 DPLL autoidle state. This is so the direct
register access can be moved out of the mach-omap2/pm24xx.c code, and other
code that needs to control this (e.g., CPUIdle) can do so via an API.
As part of this patch, remove the pm24xx.c code that formerly wrote
directly to the autoidle bits.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Some drivers wish to know whether the device that they control can
ever lose context, for example, when the device's enclosing
powerdomain loses power. They can use this information to determine
whether it is necessary to save and restore device context, or whether
it can be skipped. Implement the powerdomain portion of this by
adding the function pwrdm_can_ever_lose_context(). This is not for
use directly from driver code, but instead is intended to be called
from driver-subarch integration code (i.e., arch/arm/*omap* code).
Currently, the result from this function should be passed into the
driver code via struct platform_data, but at some point this should
be part of some common or OMAP-specific device code.
While here, update file copyrights.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The bank power state bitfields in the powerdomain data are
encoded incorrectly. These fields are intended to be bitfields,
representing a set of power states that the memory banks support.
However, when only one power state was supported by a given bank,
the field was incorrectly set to the bit shift -- not the mask.
While here, update some file copyrights.
The OMAP4 autogeneration scripts have been updated accordingly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Mark the WKUP powerdomain as being always on -- at least, as long as the
chip has power. This will be used to enable the powerdomain code to
determine whether a given powerdomain is ever able to power off. While
here, update the file copyright.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Enable new platforms and tegra drivers in tegra_defconfig. Also enable
some of the common devices several platforms, and GUID partition tables
to make it possible to boot a tegra_defconfig kernel with a ChromiumOS
filesystem.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
This patch adds the config infrastructure, the pinmux and basic
board setup code for PAZ00 (name of board inside the AC100/AZ).
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This is the final patch to enable audio support on Harmony. It additionally
relies on the latest ASoC branch being merged in, which provides the header
defining the gpio_base field in the WM8903 platform data.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch is the portion of the audio-related setup that relies additionally
on the latest Tegra I2C driver being merged.
* Define platform data for WM8903 audio codec
* Register WM8903 as an I2C device
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Register the base i2c busses on harmony. Devices coming at a later date,
but this allows for hand-probing of some of them at least.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Register the base i2c devices on seaboard. A few more are pending,
but it's a start.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
This change includes everything required to enable audio on Harmony, except
those parts which rely on code not currently in Tegra's for-next branch, i.e.
except those parts which rely on merges of the Tegra I2C driver or latest
ASoC subsystem.
* Define GPIO names for audio-related GPIOs
* Set up platform data and platform device for ASoC machine driver
* Register audio-related platform devices
* Initialize audio-related clocks
* Correctly configure pinmux and GPIO enables for audio-related pins
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This ensures they're kept in sync between platform_data definitions and
the GPIO table initialization.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch enables lcd and backlight drivers in NURI board.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the parent clock for watchdog timer for EXYNOS4.
Signed-off-by: Inderpal Singh <inderpal.s@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
